Manual.ly Logo

Einhell TE-TC 18/115 Li Manual

0.0 · 0 Ratings

PDF manual · 219 Pages

English

M: OA-GPT-5-NAN
page

/ 219

Loading...
e3d80edde6692fe616aa3bac707d81c30911 page 11
GB
- 17 -
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 16)
1. Danger! - Read the operating instructions to
reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust
which is injurious to health can be generated
when working on wood and other materials.
Never use the device to work on any materi-
als containing asbestos!
4. Caution! Wear safety goggles. Sparks ge-
nerated during working or splinters, chips and
dust emitted by the device can cause loss of
sight.
5. Store the batteries only in dry rooms with
an ambient temperature of +10°C to +40°C.
Place only fully charged batteries in storage
(charged at least 40%).
6. Danger! Risk of injury through cutting.
7. Caution! Segmented diamond cutting
wheels must not be used.
1. Safety regulations
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
fi re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
2. Layout and items supplied
2.1 Layout
1. Miter stop
2. Parallel stop
3. Wheel guard
4. Cutting table
5. Water container
6. Water container cover
7. Cutting wheel safety guard
8. Fastening screw for wheel guard
9. Fastening button for wheel guard
10. Fastening clasp
11. Water drain screw
12. On/Off switch
13. Fastening screw for splitter
14. Diamond cutting wheel
15. Outer fl ange
16. Scale
17. Housing
18. Splitter
19. Ring spanner
20. Counterholder
21. Battery (not supplied)
22. Battery catch
23. Battery safety cover
24. Mount for battery pack
25. Charger (not supplied)
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, foils or small parts. There is a danger of
swallowing or suff ocating!
•
Cordless tile cutting machine
•
Cutting wheel guard with splitter
•
Diamond cutting wheel
•
Parallel stop
•
Cross stop
Anl_TE_TC_18_115_Li_SPK13.indb 17Anl_TE_TC_18_115_Li_SPK13.indb 17 12.08.2021 16:47:0612.08.2021 16:47:06

Chat with your Einhell TE-TC 18/115 Li manual using AI

Get instant AI answers from your Einhell TE-TC 18/115 Li manual

Ask anything about the Einhell TE-TC 18/115 Li. Answers come from this manual, with the pages they are based on.

TE-TC 18/115 Li Maintenance Schedule

After every use
Clean the device immediately after use

Wipe with a clean cloth or blow out with low-pressure compressed air to keep safety devices and motor housing free of dust.

Show in the manual (page 11)
Regularly
Clean equipment with moist cloth

Use a damp cloth and mild soap. Do not use solvents and ensure no water enters the device interior.

Show in the manual (page 11)
During operation
Check wearing parts and fastenings

While running, check wearing parts and tighten any loose fasteners or verify accessory installation.

When excessive sparking occurs
Have carbon brushes checked by electrician

If excessive sparking occurs, only a qualified electrician may inspect or replace the carbon brushes.

Show in the manual (page 11)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend TE-TC 18/115 Li?

Yes No

Frequently Asked Questions

A

The machine is sold as a stationary 'solo' unit and does not include a battery or charger. It must be used only with Einhell Power X-Change Li‑Ion batteries and charged with compatible Power X chargers.

Is this answer helpful?

A

The cutter uses a 115 mm diameter diamond cutting wheel with a 22.2 mm bore. Only continuous diamond cutting wheels suited for wet tile cutting are permitted; segmented diamond wheels are explicitly forbidden.

Is this answer helpful?

A

Fill the water reservoir to the MAX mark before cutting and monitor the level during use so the diamond segment remains submerged for cooling. Refill directly into the trough and drain via the water drain screw when finished.

Is this answer helpful?

A

Wear safety goggles, a dust mask, hearing protection, and gloves. Always remove the battery before maintenance or blade changes, ensure guards are installed, and avoid cutting materials the machine isn't designed for (e.g., wood or metal).

Is this answer helpful?

A

Remove the battery, drain the water if needed, lift the wheel guard, block the motor shaft with the counterholder, loosen the nut with the ring spanner, replace the blade observing rotation direction, and retighten before restoring guards.

Is this answer helpful?

A

The cutter delivers a maximum cutting height of approximately 24 mm at 90° and 16 mm at 45°. Cut length is effectively unlimited, governed by the workpiece and proper feed control.

Is this answer helpful?

A

Clean the unit after each use, keep air vents and guards free of debris, check wear parts and fastenings regularly, avoid full battery discharge, and store batteries charged (~40% minimum) in dry conditions between +10°C and +40°C.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Cordless convenience with Power X-Change compatibility for portable, workshop-free use.
  • Water-cooled diamond blade reduces dust and extends blade life for cleaner cuts.
  • Tilting table supports jolly and miter cuts up to 45° for versatile tile profiling.
  • Compact and lightweight (≈3.4 kg) while still offering a 305×335 mm cutting table.
  • Clear scale, parallel and miter stops enable repeatable, accurate cuts for DIYers.
VS

Disadvantages

  • Sold as a body-only unit—batteries and charger are not included, adding to total cost.
  • Not designed for heavy professional or industrial use; warranty may be void for commercial use.
  • Noise and vibration levels are significant; hearing protection and care are required.
  • Only specific diamond blades allowed; segmented blades are forbidden, limiting blade choices.
  • Requires regular water management and cleaning to avoid motor or electrical damage.
M: OA-GPT-5-NAN

Product Specification

Battery

18V, Li-Ion

No-load speed

3800 rpm

Disc diameter

4.53 in

Cutting capacity

0.94 in (90°), 0.63 in (45°)

Miter cuts

45°/45° left/right

Tool mounting

Bore 0.87 in

Special features

Angle stop, Wet cutting function, Parallel stop

Dimensions (WxD)

13.19x12.01 in

Weight

7.72 lb

Scope of delivery

without charger and battery, incl. diamond cutting disc

M: OA-GPT-54-NAN

Product Description

Einhell TE-TC 18/115 Cordless Tile Cutter, stationary solo Manual

The Einhell TE-TC 18/115 cordless tile cutter is a compact, battery-powered stationary cutting machine designed for precise cutting of small to medium tiles. Lightweight at about 3.4 kg and powered by an 18 V Power X-Change lithium-ion battery (sold separately), it features a 115 mm diamond cutting wheel, a water-cooled trough, and a tilting work surface for jolly and miter cuts up to 45°. The cutter’s table measures 305 x 335 mm and it delivers cutting heights of 24 mm at 90° and 16 mm at 45°. With an idle speed of 3,800 rpm and clear scale markings, the unit balances portability and accuracy for DIYers and hobbyists handling ceramic and glazed tiles.

Key features and operation

This cordless tile cutter includes a parallel stop and miter stop for repeatable cuts, a wheel guard with splitter for safety, and a water reservoir with a removable cover to cool the diamond blade and reduce dust. It supports unlimited cut length relative to the workpiece feed and allows jolly cuts by tilting the cutting surface. The cutter is designed to accept Power X-Change batteries and must be used only with compatible chargers. LED charger status indicators and guidance for battery care are provided: keep batteries charged above 40% in storage and avoid full deep discharge to extend life.

The machine requires correct assembly before use: mount the diamond wheel with proper flange orientation, install the splitter so it aligns behind the blade, and secure the wheel guard. Always remove the battery before maintenance, blade changes, or adjustments. During operation, keep the water level at or below the MAX mark so the diamond section is covered, and feed the tile at a rate appropriate to the blade capacity to avoid chipping or kickback.

Safety and maintenance

The manual emphasizes personal protective equipment: eye protection, dust mask, hearing protection, and gloves. Noise and vibration levels are specified (approx. 80.6 dB(A) sound pressure, 93.6 dB(A) sound power), so hearing protection is recommended. Only undamaged, correctly mounted diamond cutting wheels are permitted; segmented blades are forbidden. Regular cleaning after each use, checking fastenings and wear parts (such as carbon brushes and the cutting wheel), and preventing water ingress into the motor are stressed. Replacement parts and service contacts are available via Einhell Service; a 24-month warranty applies to consumer purchases under specified conditions.

Notes

  • The machine is not intended for cutting wood or metal; misuse voids warranty.
  • Always remove the battery before assembly, maintenance, or transport.
  • Use only Power X-Change batteries and Power X chargers.
  • Keep water level sufficient to cool the diamond edge during cuts.
  • For prolonged battery life, recharge before the battery is fully discharged.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly