Manual.ly Logo

DAP Audio GIG-124CFX Manual

0.0 · 0 Ratings

PDF manual · 24 Pages

English

M: OA-GPT-54-NAN
page

/ 24

Loading...
52c477751fe235a56f280bbda7469fd8554d page 4
3
GIG-244CFX
Order code: D2288
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the system.
Never let the power-cord come into contact with other cables! Handle the power-cord and all
connections with the mains with particular caution!
Never remove warning or informative labels from the unit.
Never use anything to cover the ground contact.
Never leave any cables lying around.
Do not insert objects into air vents.
Do not connect this system to a dimmer pack.
Do not switch the system on and off in short intervals, as this would reduce the system’s life.
Do not open the device and do not modify the device.
Do not drive the inputs with a signal level bigger, than required to drive the equipment to full output.
Do not plug Mics into the console (or stage box) while Phantom Power is on. Also mute the monitor /
Pa system when turning Phantom Power on or off. Allow the system to adjust for a couple of seconds,
before setting the input gains.
Only use system indoor, avoid contact with water or other liquids.
Avoid flames and do not put close to flammable liquids or gases.
Always disconnect power from the mains, when system is not used. Only handle the power-cord by
the plug. Never pull out the plug by tugging the power-cord.
Always operate the unit with the AC ground wire connected to the electrical system ground.
Make sure you don’t use the wrong kind of cables or defective cables.
Make sure that the signals into the mixer are balanced, otherwise hum could be created.
Make sure you use DI boxes to balance unbalanced signals; All incoming signals should be clear.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power-cord is never crimped or damaged. Check the system and the power-
cord from time to time.
Please turn off the power switch, when changing the power cord or signal cable, or select the input
mode switch.
Extreme frequency boosts in connection with a high input signal level may lead to overdriving your
equipment. Should this occur, it is necessary to reduce the input signal level by using the INPUT
control.
To emphasize a frequency range, you don’t necessarily have to move its respective control upward;
try lowering surrounding frequency ranges instead. This way, you avoid causing the next piece of
equipment in your sound path to overdrive. You also preserve valuable dynamic reserve
(“headroom”)
Avoid ground loops! Always be sure to connect the power amps and the mixing console to the
same electrical circuit to ensure the same phase!
If system is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your system. Leave the
system switched off until it has reached room temperature.
If your Dap Audio device fails to work properly, discontinue use immediately. Pack the unit securely
(preferably in the original packing material)and return it to your Dap Audio dealer for service.
Repairs, servicing and electric connection must be carried out by a qualified technician.
For replacement use fuses of same type and rating only.
WARRANTY: Till one year after date of purchase.

Chat with your DAP Audio GIG-124CFX manual using AI

Get instant AI answers from your DAP Audio GIG-124CFX manual

Ask anything about the DAP Audio GIG-124CFX. Answers come from this manual, with the pages they are based on.

GIG-124CFX Maintenance Schedule

Regular
Clean the device exterior

Disconnect from mains and wipe with a damp cloth. Do not immerse in liquid or use alcohol/solvents.

Show in the manual (page 21)
Regular
Clean audio connectors

Disconnect from mains and wipe connectors with a damp cloth. Ensure they are fully dry before reconnecting.

Show in the manual (page 21)
Regular
Inspect cables

Check power and signal cables regularly for damage to prevent issues like hum loops or disconnections.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend GIG-124CFX?

Yes No

Frequently Asked Questions

A

It is designed for stage reliability with low-noise mic preamps, clip monitoring, and fast channel-level control. Multiple inputs (mic, balanced line, and stereo) plus AUX sends and built-in DSP effects make it easy to handle vocals, instruments, and playback in one compact mixer.

Is this answer helpful?

A

It offers 18 mic input channels via XLR with low-noise preamps and switchable +48V phantom power, plus 16 balanced line inputs. Stereo channels also provide additional line input options (including 6.35mm and Cinch depending on the channel).

Is this answer helpful?

A

Use the XLR mic inputs for low-impedance microphones. Turn on +48V phantom power only when your microphones require it, and avoid connecting unbalanced microphones with phantom enabled. Use the PHANTOM LED as a confirmation that +48V is active.

Is this answer helpful?

A

Yes. A dedicated +48V switch activates phantom power for the mic inputs. The setup guidance also warns not to connect incompatible microphones to the mic inputs while +48V is enabled.

Is this answer helpful?

A

Yes. A USB port allows connecting the mixer to a PC or laptop for audio playback and recording, and channel switching options let you route USB versus line or media player sources on the relevant stereo channels.

Is this answer helpful?

A

No. If a channel provides both MIC and LINE (or multiple line types), you must use one input pair only. Connecting multiple pairs simultaneously can cause interference and level reduction, resulting in unwanted noise or loss of clarity.

Is this answer helpful?

A

The built-in 24-bit DSP includes 100 presets such as Echo, Echo+Verb, Tremolo, Plate, Chorus, Rotary, Small Room, Flanger+Verb, and Large Hall. Select a preset with the effects program control and control level through the FX send and FX return paths, with mute support including a footswitch.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • 18 XLR mic channels with low-noise preamps and switchable +48V phantom power.
  • Ultra-low-noise discrete mic preamps with +48V phantom power for microphones
  • Large input flexibility: 18 mic channels plus 16 balanced line inputs and stereo options
  • 18+ inputs versatility: 16 balanced line inputs plus multiple stereo input options.
  • Professional control features: 3-band EQ with sweepable MID, compressor, clip and signal LEDs
VS

Disadvantages

  • Safety and wiring requirements are strict: correct grounding and balanced signal practices are important.
  • Must follow routing rules carefully (dont use MIC and LINE on the same channel together)
  • The system is not intended for continuous 24/7 operation; regular breaks help extend lifespan.
  • Strict operating and safety requirements reduce flexibility for quick, careless changes
  • Media playback limitations: MP3 decode only and FAT16/FAT32 supported file systems
M: OA-GPT-54-NAN

Product Description

DAP Audio GIG CFX - Compact Professional Mixer for Live Gigs and Fixed PA

The DAP Audio GIG CFX (order code D2288) is a compact, performance-focused mixing console built for live gigs, recording, and fixed installations. It combines ultra-low-noise mic preamps, flexible routing options, and a built-in 24-bit DSP effects engine with media playback support. Following the guidance in the DAP Audio GIG CFX Manual helps you set up the unit safely and get consistent sound quickly.

With 18 XLR microphone-capable inputs and 16 balanced line inputs, plus dedicated stereo channels (TRS and RCA options), the GIG CFX adapts to typical stage and studio signal chains. Each mono mic channel includes 3-band EQ with sweepable mids and clip indication, while the stereo inputs offer a 4-band EQ with clear level monitoring. Gain, low-cut filtering, and a compressor control support tight dynamics and cleaner intelligibility, even when you are working under pressure.

Monitoring and effects are handled through four AUX sends with selectable pre/post routing and a dedicated FX send path. The internal DSP offers 100 presets, and you can mute or control the effect return directly, including footswitch support. A 12-segment output level meter keeps you aware of your headroom, helping you avoid harsh clipping artifacts.

For usability, the console includes USB connectivity for PC/laptop audio, a built-in media player (MP3 via USB), and headphone output with PFL monitoring. The internal switch-mode power supply supports 100-240V operation, making the unit practical for touring setups and venues with varying power conditions.

Key results you can expect

  • Clear, controllable audio: low-noise preamps, 3-band EQ, and compressor tools help maintain headroom.
  • Flexible mixing: multiple AUX sends (pre/post), groups, and MAIN routing options support different monitoring setups.
  • Integrated workflows: USB playback/record plus MP3 media playback reduces external device juggling.
  • Reliable stage operation: clip LEDs, VU-style output metering, and defined setup order help prevent distortion.

Setup notes

  • Always verify correct mains voltage and safe cabling before powering on.
  • Avoid using MIC and LINE on the same channel simultaneously to prevent interference.
  • Use balanced connections where possible to reduce hum and ground-loop issues.

Pros and cons

Pros

  • Ultra-low noise discrete mic preamps with +48V phantom power
  • 18 mic channels plus multiple stereo input options (TRS/RCA)
  • Sweepable MID EQ and per-channel compressor for cleaner dynamics
  • 24-bit DSP with 100 presets and dedicated FX return control
  • USB audio and optional built-in media player for playback/record

Cons

  • AUX routing is channel- and bus-based, so routing mistakes can happen fast
  • Not intended for permanent continuous operation
  • Safety rules are strict (no opening/modifications, correct grounding, proper cable use)
  • Headphone output can reach very high levels, requiring careful volume control
  • Media playback is MP3-only and uses FAT16/FAT32 file systems
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly