Manual.ly Logo

DAP Audio Core Mix-3 USB Manual

0.0 · 0 Ratings

PDF manual · 22 Pages

English

M: QW-35-FL
page

/ 22

Loading...
8a5c43cd6edca9b3223ecee5faa32ab4df22 page 5
4
Do not connect this system to a dimmerpack.
Do not switch the system on and off in short intervals, as this would reduce the system’s life.
Do not open the device and do not modify the device.
Do not drive the inputs with a signal level bigger, than required to drive the equipment to full
output.
Do not plug Mics into the console (or stagebox) while Phantom Power is on. Also mute the monitor
/ Pa system when turning Phantom Power on or off. Allow the system to adjust for a couple of
seconds, before setting the input gains.
Only use system indoor, avoid contact with water or other liquids.
Avoid flames and do not put close to flammable liquids or gases.
Always disconnect power from the mains, when system is not used. Only handle the power-cord
by the plug. Never pull out the plug by tugging the power-cord.
Always operate the unit with the AC ground wire connected to the electrical system ground.
Make sure you don’t use the wrong kind of cables or defective cables.
Make sure that the signals into the mixer are balanced, otherwise hum could be created.
Make sure you use DI boxes to balance unbalanced signals; All incoming signals should be clear.
Make sure that the available voltage is not higher than stated on the rear panel.
Make sure that the power-cord is never crimped or damaged. Check the system and the power-
cord from time to time.
Please turn off the power switch, when changing the power cord or signal cable, or select the
input mode switch.
Extreme frequency boosts in connection with a high input signal level may lead to overdriving
your equipment. Should this occur, it is necessary to reduce the input signal level by using the
INPUT control.
To emphasize a frequency range, you don’t necessarily have to move its respective control
upward; try lowering surrounding frequency ranges instead. This way, you avoid causing the next
piece of equipment in your sound path to overdrive. You also preserve valuable dynamic reserve
(“headroom”)
Avoid ground loops! Always be sure to connect the power amps and the mixing console to the
same electrical circuit to ensure the same phase!
If system is dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
If the system has been exposed to drastic temperature fluctuation (e.g. after transportation), do
not switch it on immediately. The arising condensation water might damage your system. Leave
the system switched off until it has reached room temperature.
If your Dap Audio device fails to work properly, discontinue use immediately. Pack the unit
securely (preferably in the original packing material), and return it to your Dap Audio dealer for
service.
Repairs, servicing and electric connection must be carried out by a qualified technician.
For replacement use fuses of same type and rating only.
WARRANTY: Till one year after date of purchase.
Operating Determinations
This system is not designed for permanent operation. Consistent operation breaks will ensure that the
system will serve you for a long time without defects.
If this system is operated in any other way, than the one described in this manual, the product may suffer
damages and the warranty becomes void.
Any other operation may lead to dangers like short-circuit, burns, electric shock, etc.
You endanger your own safety and the safety of others!
Improper installation can cause serious damage to people and property !

Chat with your DAP Audio Core Mix-3 USB manual using AI

Get instant AI answers from your DAP Audio Core Mix-3 USB manual

Ask anything about the DAP Audio Core Mix-3 USB. Answers come from this manual, with the pages they are based on.

Core Mix-3 USB Maintenance Schedule

Regularly
Clean the device housing

Disconnect from mains and wipe with a damp cloth. Do not use alcohol or solvents.

Show in the manual (page 20)
Regularly
Clean audio connections

Disconnect from mains and wipe audio connectors with a damp cloth. Ensure they are completely dry before reconnecting.

Show in the manual (page 20)
Regularly
Inspect cables and system

Check the system and power cable for damage at regular intervals. Replace damaged cables immediately.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Core Mix-3 USB?

Yes No

Frequently Asked Questions

A

Yes, the CORE MIX-3USB has two USB Type B ports functioning as audio interfaces compatible with both Mac and PC operating systems for DJ software routing.

Is this answer helpful?

A

Use the built-in MP3 module with USB slots or SD card slots to capture master mix audio directly onto removable media without extra hardware.

Is this answer helpful?

A

The manufacturer provides a warranty until one year after the date of purchase, requiring original packing for any returns or claims.

Is this answer helpful?

A

No, fader replacement should only be carried out by a qualified technician to avoid damaging the board or voiding the warranty.

Is this answer helpful?

A

Use the electronically balanced XLR-type input. Ensure phantom power is off before plugging in the dynamic mic to avoid issues.

Is this answer helpful?

A

Yes, for PC software accessing single soundcards, installing the freeware ASIO4ALL allows proper configuration for the mixers USB ports.

Is this answer helpful?

A

The unit operates on 100 to 240Vac at 50 or 60Hz with a fuse rating of T1A. Ensure voltage matches before connecting to mains.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Dual USB audio interfaces allow seamless connection to both PC and Mac workstations for modern DJ setups.
  • Built-in MP3 recorder enables direct audio capture using USB sticks or SD cards for live performance documentation.
  • 60mm VCA faders offer durable performance and smooth control for mixing tracks during live events.
  • Independent variable FX send on every channel provides enhanced creative possibilities for sound design.
  • 3-band EQ is available on all channels to allow precise frequency adjustment per input signal.
VS

Disadvantages

  • System is not designed for permanent operation and requires consistent breaks to prevent defects.
  • Fader replacement must be carried out by a qualified technician to maintain safety and warranty coverage.
  • Power supply voltage must strictly match specifications to avoid potential damage or voiding warranty terms.
  • Unbalanced outputs on the record module may introduce noise when using very long cable runs.
  • An RMA number is required for all returns which can slow down the replacement process.
M: QW-35-FL

Product Specification

Channels

3

Equalizer

3-Band

Kill-Switches

No

Inputs

Phono In (RCA), 6x Stereo Line In (RCA), Mic In (XLR / 0.25 inch Combo), FX Return (RCA)

Outputs

Master Out (XLR), Master Out (RCA), Record Out (RCA), FX Send (RCA), Headphones (0.25 inch Jack)

Features

Audio Interface

Dimensions

10.55x14.96x3.46 in (WxHxD)

Weight

8.82 lbs

M: QW-35-FL

Product Description

Discover Professional Mixing

The DAP Audio Core Mix-3 USB offers an exciting experience for performers. This device brings excitement to any venue whether you want simple plug-and-play action or a sophisticated show. You rely on DAP Audio for excellent audio products. We design and manufacture professional audio equipment for the entertainment industry. New products are being launched regularly to keep customers satisfied.

Integrated Recording Features

The CORE MIX-3USB is a DJ mixer with 8 analogue inputs. It features 2 independent USB audio interfaces connecting your laptop. Audio of your DJ software routes directly through the MIX-3 USB. It has an independent variable fx send for each channel. The microphone channel has a 3 band EQ and talkover function. It makes MC-ing safe and easy for party jocks. The return is controlled by a 45mm fader for external effects. Low tone control on the headphone output lets you adjust your favorite sound. All the pots are firmly locked on the internal chassis. The Core Mix-3 USB has a separate fader print board.

Performance And Stability

It is equipped with unbalanced and balanced outputs. There is built in MP3 player-recorder capability. The MP3 module allows recording performances directly on USB or SD. Following the DAP Audio Core Mix-3 USB Manual ensures you get the best from the unit. It is equipped with 60mm VCA faders. The system provides the effect you need. You can connect your laptop and route the audio. This makes setup easy. The frequency response reaches 20Hz to 20Khz. Dimensions measure 268 by 381 by 88 mm. Weight is roughly 4.6 kg for heavy duty stability.

Reliability And Warranty

The manufacturer will not accept liability for damages caused by non-observance of instructions. This system contains no user-serviceable parts. Servicing refers to qualified technicians only. Never let the power-cord contact other cables. Handle the power-cord with caution. You can get some of the best quality products. So next time turn to DAP Audio for great audio equipment. Always keep the unit clean and disconnect power before cleaning. The warranty lasts for one year after date of purchase. Ensure the right color cable is connected. This setup provides years of trouble-free operation for your DJ needs.

Setup And Maintenance

Check contents upon receipt and notify dealer if damaged. Return merchandise must be sent prepaid in the original packing. Highlite will not accept returned goods without an RMA number. Be prepared to provide model number. The shipment includes power cable and user guide. Make sure signals into the mixer are balanced. Avoid ground loops for best sound. Operate the unit with AC ground wire connected. Always disconnect power from mains. Extreme frequency boosts may lead to overdriving equipment. Reduce input signal level if necessary. This machine is a great choice for professional venues.

M: QW-35-FL

© Copyright 2026 Manual.ly