Manual.ly Logo

Britax Romer Kid II Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: QW-35-FL
page

/ 2

Loading...
49490d49a42bdc5b9972ef04a37f40e64cb7 page 2
7. SAFETY NOTES
Please take the time to read these instructions carefully and keep
them to hand in the intended storage compartment
04
on the child
safety seat at all times! The instructions must be with the child safety
seat if the latter is passed on to a third party.
DANGER! For the protection of your child:
• In the event of an accident with a collision speed of more than 10 km/h,
the child safety seat may be damaged without the damage becoming
immediately visible. In this case the child safety seat must be replaced.
Please dispose of it properly.
• As a rule, have your child safety seat checked if it was damaged (e.g if it
falls on the ground).
• Regularly check all important parts for damage. Ensure that all mechanical
parts, in particular, are fully functional.
• Never lubricate or oil parts of the child seat.
•
Never leave your child unattended in the child seat in the vehicle.
• Only allow your child to enter and exit the vehicle on the pavement side.
• Protect the child safety seat from intensive direct sunlight when it is not in
use. The child safety seat can get very hot in direct sunshine. Child skin is
sensitive and could thereby be harmed.
•
The more snugly the belt ts over your child's body, the better they will be pro-
tected. Therefore avoid putting thick clothes on your child under the belt.
• Take regular breaks on long journeys in order to give your child the oppor-
tunity to play around.
• Use on the rear seat: Move the front seat forward far enough that you
child's feet cannot hit the backrest of the front seat (to prevent risk of
injury).
DANGER! For the protection of all vehicle occupants:
In the case of an emergency stop or an accident, unsecured persons or
objects may cause injury to other vehicle occupants. Please always check
that...
• the backrests of the vehicle seats are locked (i.e. that any foldable rear
seat bench latch is engaged).
• all heavy or sharp-edged objects in the vehicle (e.g. on the parcel shelf)
are secured.
• all persons in the vehicle have their seatbelts fastened.
• the child safety seat is always secured when it is in the vehicle, even if no
child is being transported.
WARNING! For your protection when handling the child seat:
• Never use the child safety seat free-standing, not even for test sitting.
• When swivelling up the backrest
07
, nothing must come between the
backrest
07
and the seat cushion
03
. You or your child could pinch your
ngers, injuring them.
•
To avoid damage, ensure that the child safety seat is not jammed in between
hard objects (car door, seat rails, etc.).
•
Keep the child safety seat in a safe place when it is not in use. Do not place
any heavy objects on the seat and do not store it directly next to sources of
heat or in direct sunlight.
CAUTION! To protect your vehicle:
•
Certain car seat covers made from more sensitive materials (e.g. velour, leath-
er, etc.) may sustain signs of wear and tear when using child safety seats. For
optimum protection of your car seat covers, we recommend using the BRITAX
RÖMER car seat protector from our range of accessories.
PAGE II
A correctly set headrest
05
ensures that the diagonal seat belt section
18
is
optimally positioned, and gives your child optimum protection.
The headrest
05
must be adjusted so that there is a space two ngers wide
between the headrest
05
and your child's shoulders.
To adjust the height of the headrest to t your
child:
1. Grip the adjustment handle
06
on the back of the
headrest
05
and pull it upwards.
This unlocks the headrest.
2. You can now move the unlocked headrest
05
to
the desired height. As soon as you release the
adjustment handle
06
, the headrest
05
will lock
into place.
3. Place the child safety seat on the vehicle seat.
4. Have your child sit down in the child safety seat and
check the height. Repeat the procedure until the
headrest
05
has the correct height.
8. ADJUSTING THE HEADREST
9. INSTALLATION
10. SECURING YOUR CHILD
05
06
05
With 3-point belt
1. Carry out the steps in Section 8 "ADJUSTING
THE HEADREST“.
2. Place the child seat on the vehicle seat. Ensure
that the backrest
07
is ush with the backrest of
the vehicle seat.
Tip! If the headrest of the vehicle seat gets in the
way, turn it the other way.
3. Carry out the steps in Section 10 „SECURING
YOUR CHILD“.
For the safety of your child, before every journey in the car check
that...
►the child safety seat is securely fastened;
►the lap belt
17
runs in the bright red belt guides on both sides of the seat
cushion
01
,
►the diagonal seat belt section
18
on the side of the vehicle seatbelt buck-
le
19
also runs through the light red belt guide
01
of the seat cushion,
►the diagonal seat belt section
18
runs through the dark red belt holder
02
of the headrest,
►the diagonal seat belt section
18
runs diagonally backward,
►the straps are tight and not twisted,
►the seatbelt buckle
19
must not be positioned on the red belt guide
01
in
the seat cushion.
DANGER! If your child tries to open the vehicle belt buckle
19
, stop the
vehicle as soon as safely possible. Check whether the child safety seat is
correctly fastened and ensure that your child is correctly secured. Explain
to your child the dangers associated with his actions.
UNFASTENING YOUR CHILD AND REMOVAL:
To unfasten your child or to remove the child safety seat, observe the
steps in Section 6 „REMOVAL“ [PAGE I]
07
The
KID II
is not installed permanently in the vehicle. It is simply secured
together with your child using the vehicle's 3-point seatbelt.
1. Have your child sit down in the child seat.
2. Pull out the vehicle belt and guide it in front of your
child to the vehicle seat buckle
19
.
DANGER! Ensure the vehicle belt is not twisted, as
otherwise the full protective effect of the
retaining system is not ensured.
3. Engage the buckle tongue in the vehicle seat buck-
le
19
with a CLICK!
4. Place the diagonal seat belt section
18
and lap
belt section
17
on the side of the vehicle seatbelt
buckle
19
into the light red belt guide
01
of the seat
cushion.
DANGER! The vehicle seatbelt buckle
19
must
not be positioned between the light red
belt guide
01
and the armrest.
5. Also place the lap belt section
17
on the other side
of the seat cushion in the light red belt guide
01
.
DANGER! The lap belt section
17
must lie as low
as possible over your child's hips on
both sides.
6. Guide the diagonal seat belt section
18
into the dark
red belt holder
02
of the headrest
05
until it lies
completely in the belt holder
02
and is not twisted.
Tip! If the backrest
16
conceals the belt holder
02
,
you can adjust the headrest
05
upwards. The diagonal
seat belt section
18
can now be easily inserted. Now
return the headrest
05
to the proper height.
7. Make sure that the diagonal belt
18
runs over your
child's shoulder, and not in front of his or her neck.
Tip! You can still adjust the height of the headrest
05
again here in the vehicle.
DANGER! The diagonal seat belt section
18
must
run diagonally backward. You can
adjust the course of the belt with your
vehicle's adjustable belt deector.
DANGER! The diagonal belt
18
must never be di-
rected forwards to the belt deector on
the vehicle. In this case, use the child
safety seat on the back seat only.
8. Tighten the vehicle seat belt by pulling on the diag-
onal seat belt section
18
.
19
18
17
01
19
17
01
18
18
18
02
05
19
BRITAX RÖMER
Kindersicherheit GmbH
Blaubeurer Straße 71
D-89077 Ulm
Germany
T.: +49 (0) 731 9345-199/-299
F.: +49 (0) 731 9345-210
www.britax.eu
BRITAX EXCELSIOR
LIMITED
1 Churchill Way West
Andover
Hampshire SP10 3UW
United Kingdom
T.: +44 (0) 1264 333343
F.: +44 (0) 1264 334146
E.:
www.britax.eu
If you have any further questions regarding its use, please feel free to
contact us:
16
05
141210_KID_II_GB.indd 2 10.12.2014 11:00:19

Chat with your Britax Romer Kid II manual using AI

Get instant AI answers from your Britax Romer Kid II manual

Ask anything about the Britax Romer Kid II. Answers come from this manual, with the pages they are based on.

Kid II Maintenance Schedule

After every accident or drop
Replace seat if damaged

If the seat is involved in an accident over 10 km/h or has fallen, it must be replaced.

Regularly
Inspect for damage

Check all important parts regularly to ensure mechanical components function perfectly.

Before each trip
Verify installation and harness

Ensure the seat is secured and the harness runs correctly through guides without twists.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend Kid II?

Yes No

Frequently Asked Questions

A

The Britax Römer Kid II is designed for children weighing between 15 and 36 kilograms, which typically corresponds to ages 4 to 12 years.

Is this answer helpful?

A

No, you must never use the Kid II with a two-point seat belt. It requires a three-point belt system to ensure proper safety and protection during travel.

Is this answer helpful?

A

You can remove the cover and wash it in a washing machine using a mild detergent on a delicate cycle at 30 degrees Celsius. Always check the care label first.

Is this answer helpful?

A

Yes, the manual states that if there is an accident with a speed over 10 km/h, the seat should be replaced even if no damage is visible to ensure continued safety.

Is this answer helpful?

A

Yes, the headrest has a simple adjustment mechanism. You pull the handle, slide the headrest to the desired height, and release it to lock it in place.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Meets strict ECE R 44/04 safety standards for high reliability
  • Color-coded belt guides simplify correct installation for parents
  • Adjustable headrest accommodates growing children from 15 to 36 kg
  • Removable fabric cover is machine washable for easy hygiene maintenance
VS

Disadvantages

  • Requires a vehicle with a three-point seat belt system only
  • Must be replaced immediately after any collision regardless of appearance
  • Original replacement covers are mandatory to keep safety certification valid
  • Not suitable for use on front seats with active airbags without caution
M: QW-35-FL

Product Specification

Group

2/3

Weight Class

15-36kg

Age Group

4-12Y

Color

black

Harness Type

3-point safety belt

Installation

forward-facing

Isofix

no

Features

adjustable backrest, height-adjustable headrest and shoulder straps, side impact protection, recline position, removable cover

Dimensions (WxDxH)

20.1x26.4-33.5x15in

Weight

11.24lbs

M: QW-35-FL

Product Description

Britax Römer Kid II Cosmos Black: Safe and Comfortable Travel for Growing Children

The Britax Römer Kid II cosmos black (2016/2017) stands as a reliable companion for parents seeking safety and style for their children during car journeys. Designed for children weighing between 15 and 36 kg, this booster seat ensures that young passengers are securely protected using the vehicle's standard three-point seat belt system. The sleek cosmos black finish not only adds a modern aesthetic to your vehicle interior but also hides dirt well, making it a practical choice for daily use.

Safety is at the core of the Kid II design. It adheres strictly to the ECE R 44/04 European safety standards, providing peace of mind for guardians. The seat features a unique color-coded guide system where the diagonal belt is marked in dark red and the lap belt in light red. This visual aid helps parents ensure the belts are routed correctly through the designated guides on the seat, minimizing the risk of improper installation. The adjustable headrest is another critical feature, allowing parents to raise or lower it to match the child's height, ensuring the shoulder belt rests comfortably across the collarbone rather than the neck.

Maintenance is straightforward with the Kid II. The fabric cover can be easily removed and washed in a machine at 30 degrees Celsius, keeping the seat fresh and hygienic. However, it is vital to use only original Britax Römer replacement covers to maintain the structural integrity and safety certifications of the product. The seat does not require complex installation tools; it simply sits on the vehicle seat and is secured by the car's existing belt. Parents must remember never to leave the child unattended in the car and to check regularly for any signs of wear or damage after accidents.

This booster seat is versatile enough for use on various rear seats, provided they have a three-point belt. It is crucial to avoid using two-point belts as they do not offer sufficient protection. With its robust construction and thoughtful design details, the Britax Römer Kid II remains a top choice for families prioritizing safety without compromising on comfort.

Important Notes

  • Always replace the seat after an accident, even if no damage is visible.
  • Do not allow thick clothing under the belt as it reduces protection.
  • Ensure the seat is always secured in the vehicle, even when empty.
M: QW-35-FL

© Copyright 2026 Manual.ly