Manual.ly Logo

Bosch PTD 1 Manual

5.0 · 5 Ratings

PDF manual · 87 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 87

Loading...
dc8d9da34818e73f444a68cf10de72e45b96 page a
10 | Deutsch
1 609 92A 1YH | (7.9.16) Bosch Power Tools
Taupunkttemperatur
Die Taupunkttemperatur gibt an, bei welcher Temperatur der
in der Luft enthaltene Wasserdampf zu kondensieren beginnt.
Die Taupunkttemperatur ist abhängig von der relativen Luft-
feuchtigkeit und der Lufttemperatur.
Ist die Temperatur einer Oberfläche niedriger als die Tau-
punkttemperatur, dann beginnt Wasser auf dieser Oberfläche
zu kondensieren. Die Kondensation ist umso stärker, je grö-
ßer die Differenz der beiden Temperaturen und je höher die
relative Luftfeuchtigkeit ist.
Kondenswasser auf Oberflächen ist eine Hauptursache für die
Schimmelbildung.
Wartung und Service
Wartung und Reinigung
Lagern und transportieren Sie das Messwerkzeug nur in der
mitgelieferten Schutztasche 16. Bewahren Sie es z.B. nicht
in einer Plastiktüte auf, deren Ausdünstungen den Luftfeuch-
te- und Temperatursensor 1 beschädigen könnten. Kleben
Sie keine Aufkleber in der Nähe des Sensors auf das Mess-
werkzeug.
Lagern Sie das Messwerkzeug nicht über längere Zeit außer-
halb eines Luftfeuchtebereichs von 30 bis 50 %. Wird das
Messwerkzeug zu feucht oder zu trocken gelagert, kann es bei
der Inbetriebnahme zu Fehlmessungen kommen.
Halten Sie das Messwerkzeug stets sauber.
Wischen Sie Verschmutzungen mit einem feuchten, weichen
Tuch ab. Verwenden Sie keine Reinigungs- oder Lösemittel.
Beim Reinigen darf keine Flüssigkeit in das Messwerkzeug
eindringen.
Reinigen Sie insbesondere den Luftfeuchte- und Temperatur-
sensor 1, die Empfangslinse 2 und die Laser-Austrittsöffnung
3 sehr vorsichtig:
Achten Sie darauf, dass keine Fusseln auf der Empfangslinse
oder der Laser-Austrittsöffnung liegen. Versuchen Sie nicht,
mit spitzen Gegenständen Schmutz aus dem Sensor oder von
der Empfangslinse zu entfernen. Bei Bedarf können Sie
Schmutz vorsichtig mit ölfreier Druckluft ausblasen.
Sollte das Messwerkzeug trotz sorgfältiger Herstellungs- und
Prüfverfahren einmal ausfallen, ist die Reparatur von einer au-
torisierten Kundendienststelle für Bosch-Elektrowerkzeuge
ausführen zu lassen. Öffnen Sie das Messwerkzeug nicht
selbst.
Geben Sie bei allen Rückfragen und Ersatzteilbestellungen
bitte unbedingt die 10-stellige Sachnummer laut Typenschild
des Messwerkzeugs an.
Senden Sie im Reparaturfall das Messwerkzeug in der Schutz-
tasche 16 ein.
Kundendienst und Anwendungsberatung
Der Kundendienst beantwortet Ihre Fragen zu Reparatur und
Wartung Ihres Produkts sowie zu Ersatzteilen. Explosions-
zeichnungen und Informationen zu Ersatzteilen finden Sie
auch unter:
www.bosch-pt.com
Das Bosch-Anwendungsberatungs-Team hilft Ihnen gerne bei
Fragen zu unseren Produkten und deren Zubehör.
www.bosch-do-it.de, das Internetportal für Heimwerker und
Gartenfreunde.
www.1-2-do.com
In der Heimwerker-Community 1-2-do.com können Sie
Produkttester werden, Ideen sammeln oder sich mit anderen
Heimwerkern austauschen.
www.diy-academy.eu, das komplette Service-Angebot der
DIY Academy.
Geben Sie bei allen Rückfragen und Ersatzteilbestellungen
bitte unbedingt die 10-stellige Sachnummer laut Typenschild
des Produkts an.
Deutschland
Robert Bosch Power Tools GmbH
Servicezentrum Elektrowerkzeuge
Zur Luhne 2
37589 Kalefeld – Willershausen
Unter www.bosch-pt.com können Sie online Ersatzteile be-
stellen oder Reparaturen anmelden.
Kundendienst: Tel.: (0711) 40040480
Fax: (0711) 40040481
E-Mail: Servicezentrum.Ele[email protected]osch.com
Anwendungsberatung: Tel.: (0711) 40040480
Fax: (0711) 40040482
E-Mail: kundenberatung.ew@de.bosch.com
Österreich
Unter www.bosch-pt.at können Sie online Ersatzteile bestel-
len.
Tel.: (01) 797222010
Fax: (01) 797222011
E-Mail: service.elektrowerkzeu[email protected].com
Schweiz
Unter www.bosch-pt.com/ch/de können Sie online Ersatz-
teile bestellen.
Tel.: (044) 8471511
Fax: (044) 8471551
E-Mail: [email protected]h.com
Luxemburg
Tel.: +32 2 588 0589
Fax: +32 2 588 0595
E-Mail: outillage.gere[email protected]osch.com
Entsorgung
Messwerkzeuge, Zubehör und Verpackungen sollen einer um-
weltgerechten Wiederverwertung zugeführt werden.
Werfen Sie Messwerkzeuge und Akkus/Batterien nicht in den
Hausmüll!
OBJ_BUCH-1625-003.book Page 10 Wednesday, September 7, 2016 11:24 AM

Chat with your Bosch PTD 1 manual using AI

Get instant AI answers from your Bosch PTD 1 manual

Ask anything about the Bosch PTD 1. Answers come from this manual, with the pages they are based on.

PTD 1 Maintenance Schedule

As needed
Clean the measuring tool

Wipe off debris with a moist, soft cloth. Do not use cleaning agents or solvents. Ensure no liquid enters the device.

Show in the manual (page 10)
As needed
Clean sensor and lenses

Clean the humidity and temperature sensor, reception lens, and laser exit opening carefully. Use oil-free compressed air if necessary; do not use pointed objects.

Show in the manual (page 10)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend PTD 1?

Yes No
0
User Pic

Michael Schneider

6 months ago

Is the device factory calibrated to ensure accurate temperature readings for home heating inspections without needing manual adjustment?

0
User Pic

Manual.ly

6 months ago

Yes, this infrared thermometer is calibrated at the factory to guarantee reliable accuracy. It is specifically designed to identify thermal weaknesses in building components and heating systems efficiently. This pre-calibration ensures you do not need expensive equipment for checking, and it avoids the delays often found in cheaper models. It meets requirements for verifying materials in older buildings.

M: qwen/qwen3.5-flash-20260224
M: qwen/qwen3.5-flash-20260224

Frequently Asked Questions

A

No, this device is designed for surface temperature measurement only. It cannot accurately measure liquids or gases due to the infrared line of sight limitations inherent in the technology.

Is this answer helpful?

A

The device provides approximately 9 hours of continuous operation depending on usage frequency and whether the laser is used frequently.

Is this answer helpful?

A

No, it does not detect spores directly. It calculates the risk of mold formation based on surface temperature, dew point temperature, and relative humidity data.

Is this answer helpful?

A

The optimal measuring distance ranges between half a meter and one meter. While measurements can be taken further away, accuracy may decrease due to the 10:1 optic ratio.

Is this answer helpful?

A

Yes, it measures relative humidity. However, ensure the sensor is not blocked or damaged by fumes. Ventilation is recommended when the air is contaminated.

Is this answer helpful?

A

To reset the software, remove the batteries, wait a few seconds, and then insert them again. If the error persists, contact authorized service.

Is this answer helpful?

A

The laser is Class 2 and generally safe for skin contact but should never be directed at eyes or reflective surfaces to avoid retinal damage.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Non-contact measurement allows safe and quick temperature checks without touching hot surfaces
  • Includes multiple modes for surface temp, thermal bridges, and mold warnings effectively
  • Protective pouch is included to prevent damage during transport and storage safely
  • Long battery life of approximately 9 hours provides reliable usage for extended tasks
  • Easy to read display with clear indicators for temperature humidity and error warnings
VS

Disadvantages

  • Cannot measure temperatures of liquids or gases due to infrared line of sight limitations
  • Requires acclimatization time when moving between extreme temperature environments quickly
  • Laser visibility is good but users must never look directly into the laser beam
  • Emissivity settings must be adjusted manually for accurate readings on different materials
  • Not suitable for commercial use or medical applications on humans or animals
M: qwen/qwen3.5-flash-20260224

Product Specification

Measuring Range

-4°F to +392°F

Display

Yes

Power Supply

Battery Powered (2x AA Battery)

Weight

0.62 lbs

Package Contents

Case, Battery

M: qwen/qwen3.5-flash-20260224

Product Description

Discover Precision with the Bosch DIY PTD 1

Home renovation and maintenance tasks demand accuracy and reliability to ensure safety and efficiency in all projects. The Bosch DIY PTD 1 Infrared Thermometer incl. Bag Manual helps DIY enthusiasts and professionals alike ensure optimal results for their work. This device is designed for non-contact measurement of surface temperature, ambient temperature, and relative humidity levels. It calculates dew point temperature and highlights potential thermal bridges and mold risk areas effectively.

The product features a clear display that shows measured values instantaneously for users to monitor closely. People can switch between different modes to suit specific project needs and inspection scenarios. The surface temperature mode is ideal for checking heating systems or kitchen appliances safely. The thermal bridge mode compares surface and ambient temperatures to detect insulation issues in walls accurately. The mold warning mode assesses moisture risks by analyzing environmental conditions over time regularly. Safety is paramount, with laser warnings clearly included on the device itself. However, strict adherence to safety guidelines is necessary to prevent eye injury from the direct beam.

Powering the device is straightforward with two AA alkaline manganese batteries or rechargeable options. The battery status is clearly indicated on the display to prevent unexpected interruptions during work sessions. A protective pouch is included securely to keep the tool safe during transport and long-term storage. This ensures the sensors remain clean and undamaged from dust or scratches over time. The laser beam helps visualize the measurement area effectively for precision. Battery life provides up to 9 hours of continuous operation depending on usage frequency. The HOLD function saves the last measured value on the screen automatically.

Understanding technical limits is vital for accurate data collection and proper usage of the tool. The device is not intended for medical use on humans or animals under any circumstances. It cannot measure liquid or gas temperatures accurately due to specific infrared line of sight limitations. Strong reflections or transparent surfaces may affect infrared results negatively for the user. Proper emissivity settings are required for precise readings on different materials like concrete or glass. The optimal measuring distance ranges between half a meter and one meter for best focus and accuracy. Environmental factors like steam or heavy dust can influence the sensor performance significantly.

Investing in this tool means investing in quality home maintenance solutions for your family. The Bosch DIY PTD 1 Infrared Thermometer incl. Bag Manual is a staple for responsible home care tasks. It empowers users to detect issues before they become major structural problems requiring repair. Whether checking insulation or monitoring climate control, this thermometer delivers consistent performance for users. Always follow the manual for best results and longevity of the equipment. Proper handling extends the life of the device significantly over many years. Enjoy peace of mind knowing your home remains safe and efficient for everyone. Cleaning requires a soft cloth without liquids penetrating the unit internals. The sensor can be damaged by paint fumes in the environment. Acclimatization time is needed if moving between hot and cold environments quickly. Do not leave it in a car during extreme heat or cold weather.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly