Manual.ly Logo

Bosch DIY POF 1200 AE Manual

0.0 · 0 Ratings

PDF manual · 105 Pages

English

M: OA-GPT-5-NAN
page

/ 105

Loading...
e4cfb8a6d76c871a8927018a69dbe447e5e3 page d
Deutsch | 13
Bosch Power Tools 1 609 92A 201 | (6.6.16)
Stellen Sie den gewünschten Radius durch Verschieben des
Fräszirkels grob ein und drehen Sie die Flügelschrauben 37
und 38 fest.
Mit dem Drehknopf 39 können Sie nach dem Lösen der Flü-
gelschraube 38 die Länge feineinstellen. Eine Umdrehung
entspricht dabei einem Verstellweg von 2,0 mm, einer der
Teilstriche am Drehknopf 39 entspricht einer Veränderung
des Verstellwegs um 0,1 mm.
Führen Sie das eingeschaltete Elektrowerkzeug mit dem
rechten Handgriff 8 und dem Griff für den Fräszirkel 36 über
das Werkstück.
Fräsen mit Führungsschiene (siehe Bild N)
Mit Hilfe der Führungsschiene 41 können Sie geradlinig ver-
laufende Arbeitsvorgänge durchführen.
Zum Ausgleich des Höhenunterschieds müssen Sie die Dis-
tanzplatte 42 montieren.
Montieren Sie den Fräszirkel/Führungsschienenadapter 35
wie im Bild gezeigt.
Befestigen Sie die Führungsschiene 41 mit geeigneten
Spannvorrichtungen, z. B. Schraubzwingen, auf dem Werk-
stück. Setzen Sie das Elektrowerkzeug mit montiertem Füh-
rungsschienenadapter 35 auf die Führungsschiene auf.
Fräsen mit Kopierhülse (siehe Bilder O–P)
Mit Hilfe der Kopierhülse 43 können Sie Konturen von Vorla-
gen bzw. Schablonen auf Werkstücke übertragen.
Wählen Sie je nach Dicke der Schablone bzw. Vorlage die ge-
eignete Kopierhülse. Wegen der überstehenden Höhe der Ko-
pierhülse muss die Schablone eine Mindeststärke von 8 mm
besitzen.
Betätigen Sie den Entriegelungshebel 20 und setzen Sie die
Kopierhülse 43 von unten in die Grundplatte 6 ein. Die Co-
diernocken müssen dabei spürbar in die Aussparungen der
Kopierhülse einrasten.
Wählen Sie den Durchmesser des Fräsers kleiner als
den Innendurchmesser der Kopierhülse.
Zum Fräsen mit der Kopierhülse 43 gehen Sie wie folgt vor:
– Führen Sie das eingeschaltete Elektrowerkzeug mit der
Kopierhülse an die Schablone heran.
– Drücken Sie den Spannhebel für Frästiefenarretierung 16
nach unten und führen Sie die Oberfräse langsam nach un-
ten, bis die eingestellte Frästiefe erreicht ist. Lassen Sie
den Spannhebel für Frästiefenarretierung 16 wieder los,
um diese Eintauchtiefe zu fixieren.
Drücken Sie ggf. den Spannhebel für Frästiefenarretierung
16 nach oben, um ihn endgültig zu fixieren.
– Führen Sie das Elektrowerkzeug mit überstehender Ko-
pierhülse mit seitlichem Druck an der Schablone entlang.
Wartung und Service
Wartung und Reinigung
Ziehen Sie vor allen Arbeiten am Elektrowerkzeug den
Netzstecker aus der Steckdose.
Halten Sie das Elektrowerkzeug und die Lüftungs-
schlitze sauber, um gut und sicher zu arbeiten.
Verwenden Sie bei extremen Einsatzbedingungen
nach Möglichkeit immer eine Absauganlage. Blasen Sie
die Lüftungsschlitze häufig aus und schalten Sie einen
Fehlerstrom-(FI-)Schutzschalter vor. Bei der Bearbei-
tung von Metallen kann sich leitfähiger Staub im Innern des
Elektrowerkzeugs absetzen. Die Schutzisolierung des
Elektrowerkzeugs kann beeinträchtigt werden.
Wenn ein Ersatz der Anschlussleitung erforderlich ist, dann
ist dies von Bosch oder einer autorisierten Kundendienststel-
le für Bosch-Elektrowerkzeuge auszuführen, um Sicherheits-
gefährdungen zu vermeiden.
Kundendienst und Anwendungsberatung
Der Kundendienst beantwortet Ihre Fragen zu Reparatur und
Wartung Ihres Produkts sowie zu Ersatzteilen. Explosions-
zeichnungen und Informationen zu Ersatzteilen finden Sie
auch unter:
www.bosch-pt.com
Das Bosch-Anwendungsberatungs-Team hilft Ihnen gerne bei
Fragen zu unseren Produkten und deren Zubehör.
www.bosch-do-it.de, das Internetportal für Heimwerker und
Gartenfreunde.
www.1-2-do.com
In der Heimwerker-Community 1-2-do.com können Sie
Produkttester werden, Ideen sammeln oder sich mit anderen
Heimwerkern austauschen.
www.dha.de, das komplette Service-Angebot der Deutschen
Heimwerker Akademie.
Geben Sie bei allen Rückfragen und Ersatzteilbestellungen
bitte unbedingt die 10-stellige Sachnummer laut Typenschild
des Elektrowerkzeuges an.
Deutschland
Robert Bosch Power Tools GmbH
Servicezentrum Elektrowerkzeuge
Zur Luhne 2
37589 Kalefeld – Willershausen
Unter www.bosch-pt.com können Sie online Ersatzteile
bestellen oder Reparaturen anmelden.
Kundendienst: Tel.: (0711) 40040480
Fax: (0711) 40040481
E-Mail: Servicezentrum.Ele[email protected]osch.com
Anwendungsberatung: Tel.: (0711) 40040480
Fax: (0711) 40040482
E-Mail: Anwendungsbe[email protected].com
Österreich
Unter www.bosch-pt.at können Sie online Ersatzteile
bestellen.
Tel.: (01) 797222010
Fax: (01) 797222011
E-Mail: service.elektrowerkzeu[email protected].com
Schweiz
Unter www.bosch-pt.com/ch/de können Sie online Ersatz-
teile bestellen.
Tel.: (044) 8471511
Fax: (044) 8471551
E-Mail: [email protected]h.com
OBJ_BUCH-323-007.book Page 13 Monday, June 6, 2016 10:00 AM

Chat with your Bosch DIY POF 1200 AE manual using AI

Get instant AI answers from your Bosch DIY POF 1200 AE manual

Ask anything about the Bosch DIY POF 1200 AE. Answers come from this manual, with the pages they are based on.

POF 1200 AE Maintenance Schedule

Frequently
Clean ventilation slots

Blow out ventilation slots frequently to ensure safe and proper working. Use compressed air especially when working with metals to prevent conductive dust buildup.

Show in the manual (page 13)
Regularly
Clean extraction adapter

Clean the extraction adapter regularly to ensure optimum dust extraction performance.

Show in the manual (page 10)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend POF 1200 AE?

Yes No

Frequently Asked Questions

A

Primarily wood, plastics and lightweight building materials. With reduced speed and appropriate carbide-tipped bits it can machine non-ferrous metals like aluminium, but it’s not intended for heavy metalworking.

Is this answer helpful?

A

It accepts 6 mm and 8 mm shank bits and provides a plunge (fräskorbhub) of 55 mm, allowing substantial depth for grooves, edge work and template routing.

Is this answer helpful?

A

Coarse depth is set using the step buffer and depth stop, which can be fine-tuned by adjusting the step-stop screws. For deep cuts use multiple shallow passes. The POF 1400 ACE variant adds a dedicated fine-adjust knob.

Is this answer helpful?

A

Yes. Mount the extraction adapter on the base plate and connect a Ø 35 mm hose to the adapter. For hazardous or carcinogenic dusts use a special vacuum and follow local regulations.

Is this answer helpful?

A

Yes. A thumbwheel (thumbwheel 23) provides speed preselection in six positions; it can be adjusted while the tool is running to match material and cutter size.

Is this answer helpful?

A

Always wear eye, hearing protection and a dust mask (P2) when needed, secure the workpiece, keep hands away from the cutting area, use dust extraction, and avoid loose clothing and jewelry.

Is this answer helpful?

A

Fold down the chip shield, press the spindle lock, insert the bit at least 20 mm into the collet, then tighten the 19 mm nut with the open-end spanner while holding the spindle lock. Do not overtighten the collet without a bit inserted.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • 1200 W motor delivers reliable power for most DIY routing tasks while keeping weight manageable.
  • 55 mm plunge depth and adjustable step stops enable precise depth control and multi-pass cutting.
  • Accepts 6 mm and 8 mm shank bits and supports many accessories (parallel guide, guide bush, compass).
  • Thumbwheel speed preselection adapts RPM to material and bit size for cleaner cuts and longer tool life.
  • Dust extraction adapter (Ø 35 mm) and chip shield support cleaner, safer working conditions.
VS

Disadvantages

  • No constant-electronic speed control (feature present on POF 1400 ACE), so RPM may vary more under load.
  • Compared with higher-end models, vibration (≈6 m/s²) and noise (~95 dB(A)) require PPE and breaks.
  • Some accessories are sold separately; complete functionality requires additional purchases.
  • Not optimized for heavy-duty metal work; non-ferrous machining requires reduced speed and suitable bits.
  • Bit changes require a 19 mm spanner and spindle lock; not as fast as single-wrench systems.
M: OA-GPT-5-NAN

Product Specification

Type

Router

Power

1200W

No-load speed

11000-28000/min

Stroke

max. 2.17in

Tool holder

Quick change system (SDS), Spindle lock

Features

Speed control, Soft grip, Auxiliary handle, Parallel guide, Dust extraction

Weight

7.50lb

Scope of delivery

3x Collet

M: OA-GPT-54-NAN

Product Description

Bosch DIY POF 1200 AE Electric Router Manual

The Bosch DIY POF 1200 AE electric router is a compact plunge router designed for precision routing tasks in wood, plastics and light building materials, with limited capability for non-ferrous metals at reduced speeds. Lightweight and ergonomic, the POF 1200 AE offers a 1200 W motor, variable speed selection, dust extraction compatibility and a 55 mm plunge depth for controlled cuts. It shares many features with the POF 1400 ACE but in a slightly lighter, more budget-friendly package.

The tool is engineered for groove cutting, edge profiling, template routing and copy routing. It accepts 6 mm and 8 mm shank bits, uses a collet secured by a 19 mm nut, and supports optional accessories including parallel guides, guide bushes, a router compass, curve guide and guide rails. Safety features and handling controls include a lock-off button for the on/off switch, spindle lock for secure bit changes, twin insulated handles for two-handed control, and a step depth system for staged plunges.

Speed preselection on the thumbwheel allows matching bit diameter and material — lower speeds for large-diameter bits or plastics, higher for hardwood and fine cutters. The design emphasizes safe operation: always secure workpieces, use dust extraction when appropriate, and wear personal protective equipment. Sound and vibration data are provided to guide protective measures (typical sound pressure ~95 dB(A); vibration ah ≈ 6 m/s²).

Assembly and maintenance are straightforward: insert bits at least 20 mm into the collet, use the spindle lock and 19 mm spanner to tighten, mount the dust adapter and extraction hose (Ø 35 mm) as needed, and keep ventilation slots and extraction ports clean. The manual recommends multiple shallow passes for deep cuts and details procedures for fine depth adjustment (POF 1400 ACE has a fine-adjustment knob; POF 1200 AE uses adjustable step stops). Practical routing techniques include use of parallel guides, auxiliary fences, guide bushes for template work, curve guides, compass attachments for circles and guide rails for straight cuts.

Overall, the POF 1200 AE is positioned for DIYers and hobbyists who need a capable, maneuverable plunge router with decent power, accessory compatibility and user-friendly depth control. It's a sensible choice for cabinetry details, edge profiling and groove work when paired with proper bits and dust extraction.

Notes

  • Wear hearing and eye protection; use a suitable dust extractor and P2 respirator when needed.
  • Use only properly sized and undamaged router bits; observe max bit diameters with/without guide bushing.
  • For repetitive deep cuts, use staged passes with the step stop to reduce strain and improve finish.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly