Manual.ly Logo

Bitspower Touchaqua G1/4 Manual

0.0 · 0 Ratings

PDF manual · 1 Pages

English

M: QW-35-FL
page

/ 1

Loading...
ff69de636a384b8c4419a66df149f37e5c3c page 1
安裝方式/Installation/安装方式
G1/4" AIR-Exhaust Fitting
V1/第一版
注意,跑水前,請先確認所有零件已安裝在正確的位置上,在不開主機,單開水泵的情况下,進行24小時的跑水測試, 確保無漏水情况後再開主機,避免發生漏水而導致電腦零件的損壞。
注意,跑水前,请先确认所有零件已安装在正确的位置上,在不开主机,单开水泵的情况下,进行24小时的跑水测试, 确保无漏水情况后再开主机,避免发生漏水而导致电脑零件的损坏。
Before filling in the water, please make sure all the components are installed correctly. To prevent any leakage which may damage the PC components, please perform a 24-hour leaking test
with only the pump connected to the power supply .
本公司保留對產品的設計更改以及解釋的權力,如有更動恕不另行通知,產品顏色與配件以實物為準。
本公司保留对产品的设计更改以及解释的权力,如有更动恕不另行通知,产品颜色与配件以实物为准。
Bitspower reserves the right to change the product design and interpretations. These are subject to change without notice. Product colors and accessories are based on the actual product.
Step 1
將按鈕按下即可排氣。
Press the button to release the air.
将按钮按下即可排气。
TA-EXAIR
建議將排氣接頭安裝於水箱且在水位之上。
It is recommended to install the air-exhaust
fitting on the reservoir, above the water line.
建议将排气接头安装于水箱且在水位之上。
注意:Bitspower建議消費者使用蒸餾水、純凈水,加入Bitspower的染劑作為水冷液使用;如客戶自行選購的水冷液導致電鍍層剝落、
水道堵塞、水泵轉動不正常、水箱管破裂或密封圈變型以致漏水等及其它不可抗力之問題時,消費者自行承擔相關產品責任。
未注水前,請勿啟動水泵電源。
注意:Bitspower 建议消费者使用蒸馏水、纯净水,加入Bitspower的染剂作为水冷液使用;如客户自行选购的水冷液导致电镀层剥落、
水道堵塞、水泵转动不正常、水箱管破裂或密封圈变型以致漏水等及其它不可抗力之问题时,消费者自行承担相关产品责任。
未注水前,请勿启动水泵电源。
Notice:
Bitspower recommends that consumers add the Bitspower dye to distilled water or purified water for their water-cooling
liquid. If the consumer chooses different water-cooling liquids, the resulting impurities may cause peeling of the coating
on some of the hardware, water channels blockage by built-up residue, improper operation of the water pump, water
tank tube breakage, and o-rings deformation leading to leakage. Any issues related to the use of inappropriate
water-cooling liquid will be the responsibility of the consumer.
Do not turn on the pump if the reservoir is empty.

Chat with your Bitspower Touchaqua G1/4 manual using AI

Get instant AI answers from your Bitspower Touchaqua G1/4 manual

Ask anything about the Bitspower Touchaqua G1/4. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Touchaqua G1/4?

Yes No

Frequently Asked Questions

A

It is designed to remove trapped air bubbles from the water cooling loop, preventing pump damage and improving cooling efficiency.

Is this answer helpful?

A

You should use distilled water mixed with Bitspower dye to prevent corrosion and channel blockage from impurities.

Is this answer helpful?

A

The system requires a twenty-four hour leak test with the pump operating before turning on the main computer power.

Is this answer helpful?

A

No, using non-recommended liquids may cause coating peeling or leaks, and the consumer will bear any resulting responsibility.

Is this answer helpful?

A

It is recommended to install the fitting on the reservoir and ensure it stays above the water line for proper venting.

Is this answer helpful?

A

Running the pump dry destroys the internal motor mechanisms instantly, leading to costly replacements and component damage.

Is this answer helpful?

A

Installation generally requires standard tools suitable for tightening G1/4 fittings and securing tubing clamps properly.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Standard G1/4 fitting ensures universal compatibility with most reservoir designs.
  • Manual release button allows for quick and easy air venting.
  • Helps prevent pump cavitation and reduces system noise significantly.
  • Simple installation process follows clear manufacturer guidelines effectively.
VS

Disadvantages

  • Requires strict adherence to leakage testing protocols before operation.
  • Risk of voided warranty if incompatible cooling liquids are used.
  • Must be installed above the water line for proper function.
  • Dry running the pump without liquid causes immediate internal damage.
  • Third-party fluid usage places full liability on the consumer.
M: QW-35-FL

Product Specification

Type

Vent Screw

Material

Brass

Connections (male)

1x G1/4"

Connections (female)

N/A

Angle

0 deg

Features

Knurled (Grooves)

M: QW-35-FL

Product Description

Revolutionizing Your Water Cooling Setup

Understanding the Bitspower Touchaqua Air Outlet Manual

High-performance liquid cooling is essential for maintaining stability in modern computing environments. The Bitspower Touchaqua Air Outlet Manual serves as a comprehensive guide for integrating efficient air management into your loop. Air pockets are the enemy of thermal efficiency because they obstruct flow channels and reduce overall cooling capacity. By utilizing this specific outlet, users can ensure their systems remain free from unnecessary gas accumulation that might otherwise cause pump noise or failure. Proper setup involves careful attention to the provided instructions regarding placement and maintenance protocols. Ensuring correct orientation prevents trapped air from blocking the reservoir.

Installation Protocol and Leak Testing

Correct installation is the foundation of a reliable water cooling system. The fitting utilizes a standard G1/4 thread design, ensuring compatibility with most reservoirs and tubing types. Experts recommend mounting the exhaust component physically above the maximum water line within the tank. This geometric advantage allows trapped air to rise and escape naturally during operation. Before introducing any fluid, a rigorous testing phase is mandatory. Connect the pump and run it for twenty-four hours without the main power source active. This extended period verifies that seals are tight and no leaks exist before full integration occurs. Avoiding leaks protects valuable hardware from water damage and corrosion risks. Ensure all clamps and tubing are tightened to specifications before starting this critical check. If pressure drops during the test phase, inspect every connection point immediately.

Fluid Compatibility and Safety Standards

Liquid selection plays a critical role in the longevity of your components. Bitspower explicitly advises using distilled water mixed with their proprietary dye agents. Deviating from these recommendations often leads to chemical residues that clog narrow internal waterways. Improper fluids can also cause coating peeling, water tank ruptures, or seal deformation leading to leaks. Users accept full responsibility for issues arising from non-recommended liquids. Additionally, never energize the pump while the water supply is empty. Dry running destroys internal pump mechanisms instantly and results in expensive replacements. Always prioritize manufacturer guidelines to maximize equipment lifespan and prevent accidents.

Operational Best Practices

The dedicated manual release button simplifies routine maintenance tasks. If air pockets are detected, pressing this button allows for quick venting without disassembling the loop. Regular monitoring ensures consistent thermal performance across all system parts. Keeping a log of maintenance cycles helps identify potential issues early. Following these steps guarantees a quiet and effective system for years to come. This product represents a vital step in custom loop construction and long-term maintenance strategies for enthusiasts.

M: QW-35-FL

© Copyright 2026 Manual.ly