Manual.ly Logo

Bitspower Motherboard Backplate for Intel CPU Manual

0.0 · 0 Ratings

PDF manual · 6 Pages

English

M: QW-35-FL
page

/ 6

Loading...
c44d05638e04719bc764c4c432933848f361 page 2
Noti ce
Before filling in the water, please make sure all the components are
installed correctly. To prevent any leakage which may damage the PC
components, please perform a 24-hour leaking test with only the pump
connected to the power supply.
Bitspower reserves the right to change the product design and
interpretations. These are subject to change without notice. Product
colors and accessories are based on the actual product.
When using leak tester on water cooling loop, in order to avoid product
damage due to excessive pressure, the input pressure should not exceed
0.5kg/cm2 (Bar). If the product is damaged due to
excessive pressure, it will be borne by the customer. Forbidden to use the
leak teser when there is water in the loop or the pump is runing.
Bitspower recommends that consumers add the Bitspower dye to distilled
water or purified water for their water-cooling liquid. If the consumer
chooses di󽗈erent water-cooling liquids, the resulting impurities may cause
peeling of the coating on some of the hardware, water channels blockage
by built-up residue, improper operation of the water pump, water tank
tube breakage, and o-rings deformation leading to leakage. Any issues
related to the use of inappropriate water-cooling liquid will be the
responsibility of the consumer.Do not turn on the pump if the reservoir is
empty.
[ 2 ]
記得上角要放對應的 LOGO!

Chat with your Bitspower Motherboard Backplate for Intel CPU manual using AI

Get instant AI answers from your Bitspower Motherboard Backplate for Intel CPU manual

Ask anything about the Bitspower Motherboard Backplate for Intel CPU. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Motherboard Backplate for Intel CPU?

Yes No

Frequently Asked Questions

A

The maximum input pressure should strictly not exceed 0.5kg per square centimeter or Bar during any testing phase to avoid permanent damage to the component.

Is this answer helpful?

A

No, M3x32 screws are explicitly stated as not included in the box and must be purchased separately for installation.

Is this answer helpful?

A

It is recommended to run the pump alone for twenty-four hours without the motherboard powered on to check for leaks safely.

Is this answer helpful?

A

Distilled water or purified water with Bitspower dye is recommended. Tap water causes blockages and damage.

Is this answer helpful?

A

Any issues related to the use of inappropriate water cooling liquid will be the responsibility of the consumer alone.

Is this answer helpful?

A

No, you should never start a pump if the reservoir is visibly empty to prevent burning the pump.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Metal backplate provides structural reinforcement for motherboards
  • Clear safety warnings regarding pressure and testing
  • Compatible with various Intel CPU sockets
VS

Disadvantages

  • Important screws like M3x32 are not included
  • User bears responsibility for damage from improper fluids
  • Pressure limit must be strictly followed during testing
M: QW-35-FL

Product Specification

Type

Backplate

Material

Stainless Steel

Compatibility

1150, 1151, 1155, 1156, 1200

Connectors

N/A

Note

Designed for Bitspower CPU Waterblock.

M: QW-35-FL

Product Description

Enhancing Your PC Cooling Experience

High performance computing often requires advanced thermal management solutions to maintain stable frame rates and prevent thermal throttling. One critical component for dedicated water cooling setups is the specialized backplate designed for motherboard stability. The Bitspower Mainboard Backplate for Intel 1150/1151/1155/1156/1200 serves this specific purpose perfectly for enthusiasts building custom rigs. It ensures that your motherboard remains rigid under the significant pressure applied by a CPU water block attachment. Without this structural reinforcement, stress on the printed circuit board could lead to cracking or damage over time.

Installation and Essential Components

When preparing for installation you must verify that all necessary tools are ready. This product focus is strictly on the metal backplate support structure. However users need to remember strictly that certain hardware elements are not provided in the box during unboxing. Specifically M3x32 screws and the CPU water block itself are excluded from this package. Motherboard support depends on the specific platform chosen by the builder. Insulation pads are often included to prevent electrical shorts between the plate and the motherboard traces. Careful handling is required during the mounting phase to avoid bending metal parts slightly.

Safety and Maintenance Protocols

Safety is paramount when operating complex liquid cooling circuits in home environments. Prior to introducing water into the loop a comprehensive leak testing procedure is mandatory for peace of mind. It is highly recommended to run the pump alone for twenty-four hours without the motherboard powered on initially. If any leaks occur during this period they can be addressed safely without damaging sensitive electronics. Pressure limits must not be exceeded during any air pressure testing phase. The maximum input pressure should stay below 0.5kg per square centimeter. Exceeding this threshold voids manufacturer safety guarantees regarding structural integrity.

Fluid Selection and Responsibility

Choosing the right coolant fluid is vital for long term system longevity and performance. Distilled water paired with specific manufacturer dyes is the overwhelmingly preferred choice for clear loops. Tap water causes rapid blockages inside narrow water channels. Impure liquids can result in electroplating peeling or pump failure. Users bear full financial responsibility for damage caused by improper fluid choices. O-rings and tubes can deform quickly due to aggressive chemical mixes. Always consult guidelines before adding any new chemicals to the loop water. Never start a pump if a reservoir is visibly empty. Bitspower recommends using purified water with their dye for optimal cooling.

M: QW-35-FL

© Copyright 2026 Manual.ly