Manual.ly Logo

Berker KNX DALI IR Presence Detector Plus 7524 10 04 Manual

0.0 · 0 Ratings

PDF manual · 4 Pages

English

M: QW-35-FL
page

/ 4

Loading...
523dfa9a0fbca3120c1022b8a246d1e003b4 page 4
Correct Disposal of This product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems).
This marking shown on the product or its literature indicates that
it should not be disposed with other household wasted at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to
promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this
product, or their local government office, for details of where and
how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms
and conditions of the purchase contract. This product should not
be mixed with other commercial wastes of disposal.
Z
M
N
L
N
L
230 V
ballast
da+ da-
DALI ballast
Remote push button
Remote load
bus
Remote push button
Remote load
Connection / Podłączenie
Remote push button
Przycisk zdalny
Montaż sufitowy
1. Za pomocą piły otwornicowej wyciąć otwór o
średnicy 60-63 mm.
2. Zamontować detektor poprzez skierowanie ku
górze obu sprężyn i wprowadzenie ich do otwo-
ru.
3. Podłączyć detektor zgodnie z zaleceniami zawar-
tymi w schemacie połączeń.
4. Zamocować osłonę zacisków i przykręcić zacisk
przewodu.
5. Ustawić potencjometry zgodnie z pożądanymi
wartościami.
Uwaga :
Grubość sufitu (t) musi zawierać się w zakresie od
10 do 28 cm.
Mocowanie zewnętrzne
(z elementem dodatkowym 1701 05)
1. Przykręcić element do puszki podtynkowej mon-
tażowej.
2. Usunąć spężyny z detektora.
3. Podłączyć przewody do detektora zgodnie z
zaleceniami zawartymi w schemacie połączeń.
4. Wcisnąć i obrócić detektor dla zblokowania w
elemencie dodatkowym.
5. Otworzyć klapkę i ustawić potencjometry
zgodnie z pożądanymi wartościami.
Wymagania dotyczące wykonania
Wymagania dla optymalnej detekcji:
- Zalecany odległość montażu od ziemi :
2,5 m —> 3,5 m
- W biurach detektor musi być zamontowany nad
stacjami roboczymi.
- Przy użyciu kilku detektorów, obszary detekcji
powinny na siebie nachodzić.
- Trzymać z dala od zakłóceń środowiskowych
(źródeł ciepła, przegród, roślin doniczkowych,
wentylacji...).
Usuwanie problemów
• Błędne włączanie punktu świetlnego :
Sprawdzić czy detektor nie jest wystawiony na
bezpośrednie działanie źródła ciepła lub światła, lub
czy nie jest umieszczony nad siecią wentylacyjną...
• Zasięg detektora jest za mały :
Ceiling mounting
1. Cut out a 60-63mm diameter hole using a
hole saw.
2. Fix the detector by pushing both springs
upward then insert them into the hole.
3. Wire the detector according to the
recommended connection diagram.
4. Mount the protective cover over the
terminals and screw the cable clamp.
5. Set potentiometers according to the
desired values.
Note :
The thickness of the support ceiling (t) must
be within 10 to 28mm range.
Surface mounting
(with accessory 1701 05)
1. Screw the accessory on the flush mounting
box.
2. Remove the protective cover and the
springs from the detector.
3. Wire the detector according to the
recommended connection diagram.
4. Push and turn the detector to lock it into
the accessory.
5. Open the slider to set the potentiometers
according to the desired values.
Implementation requirements
Requirements for optimal detection:
- Recommended installation distance from
ground : 2.5 m —> 3.5 m
- In oces, the detector must be installed
above the workstation.
- When associating several detectors,
detection areas shall overlap.
- Keep away from environmental disturbances
(heat sources, partitions, houseplants,
ventilation...).
Trouble shooting
• False switching of lighting point :
Check that the detector is not exposed directly
to a heat source or a lighting source, or is not
placed above a ventilation grid...
• The range of the detector is too short :
Check whether the distance of the device from
the ground is sucient and its location is optimal.
• The light regulation on low brightness levels
may fluctuate : check the dimming range of the
used ballasts and use preferably 1-100%
devices.
Technical features
Electrical characteristics
Supply voltage (for the product) :
KNX bus 30V s
Supply voltage (DALI/DSI bus) :
230V v +10/-15% 50/60Hz
240V v +/-6% 50/60Hz
Consumption with no load : 12mA on the bus /
60mW on mains
DALI/ DSI output capacity : 24 ballasts
Functional characteristics
Lighting output operating time : 1 min. —> 1 h
Brightness level : 5 —> 1000 Lux
Recommended installation height :
2,5 m —> 3,5m
Detection range : Ø 7m (installed product
height : 2.5m)
Products can be connected in parallel.
Hole size required : 60mm
Environment
Operating temperature : -10 °C —> +45 °C
Storage temperature : -20 °C —> +60 °C
Class of insulation : II
IK 03
Index of protection : IP41
Fire resistance : 650°C
KNX medium : TP1
KNX Configuration Mode : S-mode
Connection capacity :
0.5mm
2
to 0,75mm
2
flexible,
0.5mm
2
to 0,75mm
2
rigid
Sprawdzić czy odległość urządzenia od ziemi
jest wystarczająca i lokalizacja optymalna.
• Przy niskim poziomie jasności podczas regu-
lacji światło może migać:
sprawdzić zakres ściemniania zastosowanych
stateczników żarówek; korzystać z urządzeń
pracujących w zakresie 1 – 100%.
Dane techniczne
Charakterystyka elektryczna
Napięcie zasilania (dla produktu) :
szyna KNX 30V s
Napięcie zasilania (szyna DALI/DSI) :
230V v +10/-15% 50/60Hz
240V v +/-6% 50/60Hz
Pobór mocy bez obciążenia : 12 mA na szynie /
60 mW w sieci zasilającej
Pojemność wyjściowa DALI/DSI : 24 obciążenia
Charakterystyka funkcjonalna
Czas pracy oświetlenia : 1 min —> 1 godz.
Poziom jasności : 5 —> 1000 luksów
Zalecana wysokość montażu :
2,5 m —> 3,5m
Zakres detekcji : Ø 7m
(wysokość montażu produktu : 2,5 m)
Produkty można połączyć równolegle.
Wymagana średnica otworu : 60 mm
Środowisko
Temperatura pracy : -10 °C —> +45 °C
Temperatura przechowywania :
-20 °C —> +60 °C
Klasa izolacji : II
IK 03
Stopień ochrony : IP41
Odporność ogniowa : 650°C
Medium komunikacyjne KNX : TP1
Tryb konfiguracji KNX : S-mode
Przekrój przyłączy :
od 0,5 mm
2
do 0,75 mm
2
giętkie,
od 0,5 mm
2
do 0,75 mm
2
sztywne
Prawidłowe usuwanie produktu
(zużyty sprzęt elektryczny i
elektroniczny).
Oznaczenie umieszczone na produkcie lub w odnoszących
do niego tekstach wskazuje, że produkt po upływie okresu
użytkowania nie należy usuwać z innymi odpadami pocho-
dzącymi z gospodarstw domowych. Aby uniknąć szkodli-
wego wpływu na środowisku naturalne i zdrowie ludzi ws-
kutek niekontrolowanego usuwania odpadów, prosimy o
oddzielenie produktu od innego typu odpadów oraz odpo-
wiedzialny recycling w celu promowania ponownego uży-
cia zasobów materialnych jako dobrej praktyki.
W celu uzyskania informacja na temat miejsca i sposobu
bezpiecznego dla środowiska recyklingu tego produktu
użytkownicy w gospodarstwach domowych powinni skon
-
taktować się z punktem sprzedaży detalicznej, w którym
dokonali zakupu produktu lub organem władz lokalnych.
Użytkownicy w firmach powinni skontaktować się ze
swoim dostawca i sprawdzić warunki umowy zakupu. Pro
-
duktu nie należy usuwać z innymi odpadami komercyjnymi.
Factory settings
Luminosity threshold 400 lux
Lighting time 20 min.
Mode Presence
Power Up OFF
Active cell
(Luminosity Cell)
ON
Ustawienia fabryczne
Próg siły światła 400 luksów
Czas oświetlenia 20 min
Tryb Obecność
Włączanie zasilania OFF (wył.)
Aktywna fotokomórka (foto-
komórka siły światła)
ON (wł.)
Usable throughout Europ
e
å
and in Switzerland
Nadaje się do użytku w krajach europejskich
å
i Szwajcarii
4 Berker GmbH & Co. KG - Klagebach 38 - 58579 Schalksmühle/Germany - Tel. + 49 (0) 23 55/90 5-0 Fax + 49 (0) 23 55/90 5-111 - www.berker.com
6LE004064A

Chat with your Berker KNX DALI IR Presence Detector Plus 7524 10 04 manual using AI

Get instant AI answers from your Berker KNX DALI IR Presence Detector Plus 7524 10 04 manual

Ask anything about the Berker KNX DALI IR Presence Detector Plus 7524 10 04. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend KNX DALI IR Presence Detector Plus 7524 10 04?

Yes No

Frequently Asked Questions

A

The detector offers a circular detection range of 7 meters in diameter when installed at the recommended height of 2.5 meters.

Is this answer helpful?

A

Yes, you can perform surface mounting using the optional accessory 1701 05, which allows the unit to be fixed securely to a flush mounting box.

Is this answer helpful?

A

A single Berker KNX DALI IR Presence Detector Plus can manage up to 24 DALI or DSI ballasts simultaneously.

Is this answer helpful?

A

Flickering usually occurs due to incompatible dimming ranges. You should verify your ballast specifications and preferably use 1-100% dimming devices.

Is this answer helpful?

A

The recommended installation height is between 2.5 and 3.5 meters to ensure optimal detection performance and coverage.

Is this answer helpful?

A

Yes, it must be recycled as electronic waste and cannot be thrown in regular household trash to protect the environment.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Supports up to 24 DALI devices for extensive lighting control
  • Wide detection range of 7 meters diameter at optimal height
  • Adjustable sensitivity and timing via built-in potentiometers
  • Sleek Polar White Matte finish fits modern interiors perfectly
  • Compatible with both KNX and DALI/DSI bus systems
VS

Disadvantages

  • Requires precise 60-63mm hole cutting for ceiling installation
  • May experience flickering if used with incompatible dimmers
  • Surface mounting requires additional accessory 1701 05
  • Sensitive to direct heat sources and ventilation drafts
  • Initial setup requires understanding of KNX configuration modes
M: QW-35-FL

Product Specification

Type

Motion Detector

Sensors

Infrared

Alarm Zones

1

Standard

N/A

Detection Range

23 ft

Detection Angle

360°

Operating Temperature

14°F to 113°F

Dimensions

Ø3.15x2.76 in

Protection Class

IP41

M: QW-35-FL

Product Description

Berker KNX DALI IR Presence Detector Plus: Smart Lighting Control in Polar White Matte

The Berker KNX DALI IR Presence Detector Plus represents a pinnacle of modern automation technology, designed to seamlessly integrate into intelligent building systems. Finished in a sophisticated Polar White Matte, this device offers more than just motion detection; it provides a comprehensive solution for energy efficiency and user comfort. By combining KNX bus connectivity with DALI lighting control capabilities, the detector ensures that lights respond instantly to human presence while maintaining optimal brightness levels based on ambient conditions.

Installation is straightforward whether you choose ceiling mounting or surface mounting using accessory 1701 05. The unit requires a precise 60-63mm hole for recessed installation or can be easily clipped onto a standard box for surface application. Once installed at the recommended height between 2.5 and 3.5 meters, the sensor covers a circular area of up to 7 meters in diameter. This wide coverage makes it ideal for offices, corridors, and large residential spaces where consistent lighting is essential without manual intervention.

The device features adjustable potentiometers that allow users to customize the sensitivity, light threshold, and delay times according to specific needs. Factory settings default to a luminosity threshold of 400 lux and a switch-off delay of 20 minutes, but these can be fine-tuned to prevent flickering or false triggers. The detector intelligently manages power by switching off lights when no movement is detected, significantly reducing energy consumption. It supports up to 24 DALI devices, making it a robust choice for larger installations requiring centralized control.

Beyond functionality, the Berker KNX DALI IR Presence Detector Plus adheres to strict environmental standards. It is built to last with an IP41 rating and fire resistance up to 650 degrees Celsius, ensuring safety in various environments. The product is fully recyclable and marked for proper disposal as electronic waste, reflecting the manufacturer's commitment to sustainability. Whether you are upgrading an existing system or designing a new smart home, this detector delivers reliable performance with a sleek, unobtrusive design that complements any interior decor.

Key Notes

  • Ensure detection zones overlap when installing multiple units for full coverage.
  • Avoid placing the sensor directly above heat sources or ventilation outlets to prevent malfunctions.
  • Use 1-100% dimming ballasts to avoid flickering at low light levels.
M: QW-35-FL

© Copyright 2026 Manual.ly