Manual.ly Logo

Benning CFlex 2 Manual

0.0 · 0 Ratings

PDF manual · 60 Pages

English

M: OA-GPT-54-NAN
page

/ 60

Loading...
f36b779df941278315cceb76a2c772bcfd62 page 8
07/ 2014
BENNING CFlex 2
4
D
* Die Messgenauigkeit ist spezifiziert für eine Sinuskurvenform. Die angegebe ne Genauigkeit
ist spezifiziert für Leiter, die mit der Messschleife
mittig um fasst werden (siehe Bild 3). Für
Leiter die nicht mittig umfasst werden, muss ein zusätzlicher Fehler berücksichtigt werden.
Abstand von der Mitte Positionsfehler
25 mm ± (1,0 % des Messwertes)
50 mm ± (2,0 % des Messwertes)
75 mm ± (3,0 % des Messwertes)
8. Messen mit dem BENNING CFlex 2
8.1 Vorbereiten der Messung
Benutzen und lagern Sie den BENNING CFlex 2 nur bei den angegebenen Lager- und
Arbeitstemperaturen, vermeiden sie dauernde Sonneneinstrahlung.
- Die zum Lieferumfang gehörenden Sicherheitsmessleitung entspricht in Nennspannung
und Nennstrom der BENNING CFlex 2. Die Sicherheitsmessleitung ist fest mit dem
BENNING CFlex 2 verbunden und nicht abnehmbar.
- Isolation der Sicherheitsmessleitungen überprüfen. Wenn die Isolation be schädigt ist, ist
des BENNING CFlex 2 sofort auszusondern.
- Starke Störquellen in der Nähe der BENNING CFlex 2 können zu instabiler Anzeige und zu
Messfehlern führen.
Maximale Spannung gegen Erdpotential beachten!
Elektrische Gefahr!
Die höchste Spannung, die an dem BENNING CFlex 2 gegenüber Erdpotential lie gen darf, be-
trägt 600 V CAT IV/ 1000 V CAT III.
8.2 Wechselstrommessung
- Mit dem Drehschalter
den Messbereich 30 A, 300 A oder 3000 A wählen.
- Mit der flexiblen Messschleife
den einadrigen, stromdurchflossenen Leiter mittig umfas-
sen.
- Messwert in der Digitalanzeige
7
ablesen.
siehe Bild 2 a: Wechselstrommessung
siehe Bild 2 b: Wechselstrommessung
9. Instandhaltung
Vor dem Öffnen den BENNING CFlex 2 unbedingt spannungsfrei schalten!
Elektrische Gefahr!
Die Arbeit an dem geöffneten BENNING CFlex 2 unter Spannung ist ausschließlich
Elektrofachkräften vorbehalten, die dabei besondere Maßnahmen zur Unfallverhütung
treffen müssen.
So machen Sie den BENNING CFlex 2 spannungsfrei, bevor Sie das Gerät öffnen:
- Entfernen Sie zuerst den BENNING CFlex 2 vom Messobjekt.
Der BENNING CFlex 2 besitzt keine Sicherung.
9.1 Sicherstellen des Gerätes
Unter bestimmten Voraussetzungen kann die Sicherheit im Umgang mit dem BENNING CFlex 2
nicht mehr gewährleistet sein, z.B. bei:
- Sichtbaren Schäden am Gehäuse,
- Fehlern bei Messungen,
- Erkennbaren Folgen von längerer Lagerung unter unzulässigen Bedingungen und
- Erkennbaren Folgen von außerordentlichen Transportbeanspruchungen.
In diesen Fällen ist der BENNING CFlex 2 sofort von der Messstelle zu entfernen und gegen
erneute Nutzung zu sichern.
9.2 Reinigung
Reinigen Sie das Gehäuse äußerlich mit einem sauberen und tro cken en Tuch (Ausnahme
spezielle Reinigungs tücher). Verwenden Sie keine Lösungs- und/ oder Scheuermittel, um das
Gerät zu reinigen. Achten Sie unbedingt darauf, dass das Batteriefach und die Batterie kontakte
nicht durch auslaufendes Batterie-Elektrolyt verunreinigt wer den.
Falls Elektrolytverunreinigungen oder weiße Ab la gerungen im Bereich der Batterie oder des
Bat teriegehäuses vorhanden sind, reinigen Sie auch diese mit einem trockenen Tuch.

Chat with your Benning CFlex 2 manual using AI

Get instant AI answers from your Benning CFlex 2 manual

Ask anything about the Benning CFlex 2. Answers come from this manual, with the pages they are based on.

CFlex 2 Maintenance Schedule

Remind me when maintenance is due
Yearly
Calibrate the instrument

Send the device to the factory service center annually to maintain specified measurement accuracy.

When required
Replace batteries

Replace the two AAA batteries when the battery symbol appears on the display.

As needed
Clean the exterior

Wipe the housing with a clean dry cloth. Do not use solvents or scouring agents.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend CFlex 2?

Yes No

Frequently Asked Questions

A

It measures alternating current using a flexible current loop. The device is designed for AC-only current measurement and supports ranges up to 3000 A.

Is this answer helpful?

A

Yes. It uses TRUE RMS measurement, which helps provide more reliable readings for AC currents, especially when the waveform is close to sinusoidal.

Is this answer helpful?

A

The meter offers three AC current ranges: 30 A, 300 A, and 3000 A. The rotary switch is used to select the desired range.

Is this answer helpful?

A

No. The meter is intended for dry environments only and has IP30 protection, which does not provide water resistance.

Is this answer helpful?

A

Yes. HOLD freezes the current reading on the display, while MIN/MAX stores and cycles through the highest, lowest, and current measured values.

Is this answer helpful?

A

It runs on two 1.5 V AAA batteries. A battery symbol appears on the display when the battery voltage becomes too low.

Is this answer helpful?

A

Centering improves accuracy. The manual states that position errors increase when the conductor is placed off-center inside the flexible measuring loop.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Flexible loop design makes it easier to measure current in tight spaces and around large conductors.
  • TRUE RMS measurement improves usefulness for real-world AC readings.
  • Wide range up to 3000 A suits both everyday and heavy-load applications.
  • HOLD, MIN/MAX, and backlight functions add convenience during troubleshooting.
VS

Disadvantages

  • Works only for AC current, so it is not a universal clamp meter for DC applications.
  • No water protection; it is intended for dry environments only.
  • Accuracy drops if the conductor is not centered in the loop.
  • No overload warning is provided when the range is exceeded.
M: OA-GPT-54-NAN

Product Specification

Measurement range

max. 3,000A, max. 600V

M: OA-GPT-54-NAN

Product Description

Benning CFlex 2 True RMS Current Clamp Multimeter

Flexible AC Measurement for Professional Use

The Benning CFlex 2 is a flexible digital TRUE RMS current clamp multimeter designed for measuring alternating current in a practical, non-intrusive way. Built for electricians and trained technical users, it combines a lightweight body with a long flexible measuring loop, making it easier to reach conductors in tight or crowded installations. With measurement ranges of 30 A, 300 A, and 3000 A AC, it covers everything from smaller branch circuits to heavy-duty loads.

What makes the Benning CFlex 2 stand out is its flexible clamp design. Instead of a rigid jaw, it uses a loop that can wrap around a single live conductor, helping users measure current where traditional clamp meters may be awkward to place. The device uses TRUE RMS technology, which means it reads the effective value of AC current more reliably when the waveform is close to sinusoidal. This is especially useful in maintenance, troubleshooting, and inspection work.

The device also includes practical functions that improve everyday use. HOLD stores the displayed value, MIN/MAX captures the highest and lowest readings, and the built-in display light helps in low-light environments. A rotary switch handles both power and range selection, while the automatic shutoff feature helps preserve battery life. The meter runs on two AAA batteries and includes a battery warning symbol when power drops too low.

Safety is clearly a major part of the Benning CFlex 2 Manual. The meter is intended for dry environments only and is rated for up to 600 V CAT IV or 1000 V CAT III. It should always be used with care around live conductors, and accuracy is best when the flexible loop is centered around the conductor. The manual also notes that the unit is compact, easy to store, and suitable for regular recalibration to maintain accuracy.

Overall, the Benning CFlex 2 is a specialized current measurement tool that balances flexibility, readability, and safety. It is a strong choice for professionals who need a portable AC current solution with a wide measurement range and helpful data-hold features.

Notes

  • Best suited for dry indoor electrical work
  • Accuracy depends on centered placement and sinusoidal AC
  • Regular calibration helps maintain measurement precision
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly