Manual.ly Logo

Austria Email EHT Manual

0.0 · 0 Ratings

PDF manual · 44 Pages

English

M: OA-GPT-54-NAN
page

/ 44

Loading...
270b3a17738c5efaa2287e15a791eeb67d65 page e
Elektrospeicher EHT - 50, 80, 100, 120, 150 Liter
14
231769-10
14. KONTROLLE, WARTUNG, PFLEGE
a) Während des Aufheizens muss das Dehnwasser aus dem Ablauf des Sicherheitsventils
sichtbar abtropfen (bei drucklosem Anschluss tropft das Dehnwasser aus dem Ventil
der Mischbatterie). Bei voller Aufheizung (ca. 80 °C) beträgt die Dehnwassermenge
ca. 3,5 % des Speichernenninhaltes.
Die Funktion des Sicherheitsventils ist regelmäßig zu überprüfen. Beim Anheben oder Drehen
des Sicherheitsventilprüfknopfes in Stellung „Prüfen“ muss das Wasser ungehindert aus dem
Sicherheitsventilkörper in den Ablauftrichter ießen.
Achtung: Der Kaltwasserzulauf und Teile der Speicheranschlussarmatur können dabei heiß
werden.
Wird der Warmwasserbereiter nicht aufgeheizt oder Warmwasser entnommen, darf aus dem
Sicherheitsventil kein Wasser abtropfen. Wenn dies der Fall ist, ist entweder der Wasserleitungsdruck
zu hoch (über 5,5 bar Druckminderventil einbauen) oder das Sicherheitsventil defekt. Bitte sofort
den Installationsfachmann rufen!
b) Bei stark kalkhaltigem Wasser ist die Entfernung des sich im Speicherinnenkessel bildenden
Kesselsteines sowie des frei abgelagerten Kalkes nach ein bis zwei Betriebsjahren durch einen
Fachmann erforderlich.
Die Reinigung erfolgt durch die Flanschöffnung - Heizansch ausbauen, Speicher reinigen,
bei der Montage des Heizansches ist unbedingt eine neue Dichtung zu verwenden. Der
spezialemaillierte Innenbehälter des Warmwasserbereiters darf nicht mit Kesselsteinlösemittel in
Berührung kommen - nicht mit der Entkalkungspumpe arbeiten. Kalkansatz mit Holz entfernen
und aussaugen oder mit einem Lappen aus wischen.
Abschließend ist das Gerät gründlich durchzuspülen (entsprechend ÖNORM H5195-1) und der
Aufheizvorgang wie bei der ersten Inbetriebnahme zu beobachten.
c) Zur berechtigten Inanspruchnahme der seitens der AE-AG gewährten Garantie, bedarf die
eingebaute Schutzanode einer Überprüfung durch den Fachmann im Abstand von maximal 2
Betriebsjahren. Der Schutzstromableitwiderstand unter der Heizkörperbefestigungsschraube darf
bei Wartungsarbeiten nicht beschädigt oder entfernt werden.
d) Für die Reinigung des Gerätes keine scheuernden Putzmittel und keine Farbverdünnungen (wie
Nitro, Trichlor usw.) verwenden.
Am besten ist die Reinigung mit einem feuchten Tuch unter Beigabe von ein paar Tropfen eines
üssigen Haushaltsreinigers.
Bei Servicearbeiten ist es angezeigt, auch den Reinigungs- und Serviceansch zu öffnen, um den
Speicher auf eventuelle Einschwemmungen und Verunreinigungen zu prüfen und diese gegebenenfalls
zu entfernen.
15. FUNKTIONSSTÖRUNGEN
Wenn das Speicherwasser nicht aufgeheizt wird, prüfen Sie bitte, ob im Verteiler der Leitungsschutz-
schalter (Sicherungsautomat) oder die Schmelzsicherung angesprochen hat und kontrollieren Sie die
Einstellung des Temperaturreglers.
In allen anderen Fällen versuchen Sie nicht, die Störung selbst zu beheben. Wenden Sie sich bitte
entweder an einen konzessionierten Installateur oder an unseren Kundendienst. Für Fachleute
bedarf es oft nur wenige Handgriffe und der Speicher ist wieder in Ordnung. Bitte geben Sie bei der
Verständigung Typenbezeichnung und Fabrikationsnummer, die Sie auf dem Leistungsschild Ihres
Elektrospeichers nden, an.

Chat with your Austria Email EHT manual using AI

Get instant AI answers from your Austria Email EHT manual

Ask anything about the Austria Email EHT. Answers come from this manual, with the pages they are based on.

EHT Maintenance Schedule

Remind me when maintenance is due
Every 6 months
Test safety valve venting and function

Operate the safety valve test knob to ensure water flows freely into the drain funnel. Check if the valve reseats properly after release.

Show in the manual (page 11)
Yearly
Inspect and replace safety valve if needed

Check for leaks or failure to open during heating. Replace the complete valve if damaged or leaking permanently.

Show in the manual (page 11)
Every 2 years
Remove boiler scale from tank

In hard water areas, have a professional remove limescale via the flange opening using wood tools; do not use chemical descalers.

Show in the manual (page 14)
Every 2 years
Check protective anode

An expert must check the installed reactive anode to maintain warranty validity; do not damage the shunt resistor below the heating screw.

Show in the manual (page 14)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend EHT?

Yes No

Frequently Asked Questions

A

The Austria Enamel EHT range covers electric storage water heaters from 50 to 150 litres (50, 80, 100, 120, and 150 L), allowing you to match capacity to household usage.

Is this answer helpful?

A

The heater warms the stored service water and the temperature controller automatically switches heating on and off to hold the selected tank temperature. If water temperature drops due to hot water withdrawal or cooling, the heating resumes until the target temperature is reached.

Is this answer helpful?

A

The knob provides four main positions: frost protection (up to about 30 C), about 40 C for warm use, an economical setting around 60 C, and about 80 C for hotter storage. Notes: the left end stop is not a full off position, and day-current use should not exceed the economical setting.

Is this answer helpful?

A

For tanks marked nominal pressure 6 bar, pressure-proof connection is allowed with line pressures up to 5.5 bar, typically with a pressure reducing valve if needed. The system must be fitted only with a tested membrane safety valve or a safety valve combination and installed with correct discharge routing.

Is this answer helpful?

A

The safety valve venting facility should be operated periodically, with a suggested interval of every 6 months to avoid blockages from limescale. If malfunctions occur (leaks or no response during heating), a licensed professional should repair or replace the safety valve.

Is this answer helpful?

A

For strongly calciferous water, descaling is recommended by a specialist after about 1 to 2 years of operation. Cleaning is performed through the flange opening, using a new seal when reassembled, and the enamelled interior should not be treated with unsuitable descaling chemicals.

Is this answer helpful?

A

First check the circuit breaker or fuse and confirm the temperature controller setting. Do not attempt further internal troubleshooting. Contact a licensed installer or customer service, and provide the model designation and manufacturing number from the rating plate.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Efficient operation with thermostat-controlled heating that cycles on and off to maintain the selected tank temperature.
  • Low standby energy use supported by high-quality CFC-free PU foam insulation and measured 24-hour consumption.
  • Durable enamelled internal boiler designed for long-term storage of service water.
  • Practical temperature settings (frost protection, about 40 C, about 60 C eco, about 80 C) to match daily needs.
  • Safety temperature limiter that stops further heating at a maximum water temperature of 110 C.
VS

Disadvantages

  • Installation and first commissioning must be carried out by a licensed professional in accordance with the requirements.
  • Requires frost-free operation and correct access for maintenance, repair, or replacement.
  • Left stop on the temperature knob does not provide a true off/shutdown position for heating.
  • Proper pressure-proof plumbing depends on correctly installed, tested membrane safety valves and correct line pressures.
  • Ongoing upkeep is required, including safety valve checks and descaling for hard water.
M: OA-GPT-54-NAN

Product Specification

Energy efficiency class

C

Temperature control

95-176°F

Construction type

closed (pressure-resistant)

Mounting type

Wall mounting

Special features

Frost protection

Noise level

15dB(A)

M: GO-GEM-FL-25

Product Description

Austria Enamel EHT Manual: Austria Enamel EHT Electric Storage Water Heaters (50-150 L)

Austria Enamel EHT brings efficient electric hot water storage to everyday life with a durable, enamelled internal boiler and an automatic heating cycle. A heating unit warms the service water, while the built-in temperature controller turns operation on and off to maintain your selected tank temperature. If the water cools between draws, heating resumes until the setpoint is reached.

Designed for real-world hot water use, the EHT range is offered in sizes from 50 to 150 litres. Typical daily demand varies with household size, fixtures, insulation, pipe runs, and personal habits, so choosing the right tank volume helps avoid unnecessary standby losses. The control knob offers four main positions, including frost protection (up to about 30 C), practical comfort around 40 C, an economical setting around 60 C, and higher heat around 80 C. This makes it easier to match usage patterns while supporting energy savings.

Energy efficiency is a core feature: CFC-free PU foam insulation helps reduce heat loss, and standby energy consumption is measured at about 0.72 to 1.455 kWh per 24 hours depending on tank size. Lower set temperatures are especially economical, and keeping the temperature only as high as needed can also reduce limescale formation inside the tank.

For pressure-proof installation, tanks marked with a nominal pressure of 6 bar can be connected using a maximum line pressure up to 5.5 bar. The system must include a tested membrane safety valve or safety valve combination, installed correctly to protect the tank during expansion and to prevent damage from overpressure. A safety temperature limiter also shuts down further heating if the water temperature reaches a maximum of 110 C, adding an extra layer of protection.

Key results

  • Stable hot water temperatures thanks to automatic on/off control of the heating cycle.
  • Low standby energy thanks to CFC-free PU foam insulation.
  • Efficient daily performance through selectable temperature positions matched to demand.
  • Safer pressure-proof operation when paired with the correct safety valve arrangement.

Notes

  • Installation and first commissioning should be performed by a licensed professional.
  • The room must be frost-free; the water heater must be accessible for maintenance.
  • For service life: ventilate the safety valve periodically (every 6 months), and plan regular checks and descaling for hard water; have the protective anode checked every max 2 years.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly