Manual.ly Logo

Atika RMC 40-400 Manual

0.0 · 0 Ratings

PDF manual · 117 Pages

English

M: QW-35-FL
page

/ 117

Loading...
099976b7844054ffea99f583927ab5a84673 page 13
18
Working instructions
Before commencing work, ensure the following:
You may not start to operate the machine until you
have read these operating instructions, observed
all the instructions given and installed the
machine as described!
Provide for a safe and cleaned workplace. Remove from
the working area objects which might be thrown off.
Before starting your work make sure that:
the tools and bolts are not worn or damaged. To avoid
any unbalance worn or damaged tools and bolts must
only be replaced as a whole set.
the cutting blade is in proper condition (see „Blade
replacement“)
all screw connections are tight
no other persons or animals stay within the working
area,
you can always step back without any barriers,
you have always a secure standing position.
When working on slopes, always position yourself perpendi-
cular to the incline and ensure safe footing.
Use the unit only on slopes with a gradient less than
15°. This corresponds to a slope of roughly one
metre over a length of 4 metres.
Always keep your hands and feet at a safe distance to
the rotating tool.
Working with the lawn mower
Regular mowing is important for a healthy lawn. The
recurring cut causes the grasses to branch out at the base and
the surface remains beautifully dense. How often you want to
mow depends on the growth rate of the lawn. In the main
growth period (May - June) twice a week, otherwise once a
week.
Do not mow when the lawn is wet or too hot.
Make sure that the cutting blade is always sufficiently
sharp, otherwise the blades of grass will fray when mowing
and the lawn will turn yellow.
Select the appropriate cutting height (see “Adjusting the
cutting height”)
Take care not to overload the lawn mower.
In case of excessive strain, the motor speed drops
and the motor noise changes.
Stop and release the switch lever
Wait until the cutting blade stops
Set a higher cutting height
Run the mower over your lawn at an appropriate,
even speed in straight lines.
The lawnmower should always project one wheel
width into the cut mowing track. In this way, a
seamless and strip-free surface is created.
If you are working with a collecting bag, empty it in time.
Mulching
During mulching, the discharge channel is closed by the
mulching insert. This cuts the grass several times until it falls
finely chopped to the ground, where it then decomposes. This
provides the lawn with important nutrients that it needs to grow
and thrive and also protects it from drying out.
Keep the lawn short, mow regularly so that too much mulch
material is not produced at once.
Do not cut more than 20 mm of grass.
Push the lawn mower slowly when mulching.
Ensure that the cutting tracks overlap.
In any case, adhere to all safety notes (see "Safe
working").
Maintenance and cleaning
Before each maintenance and cleaning
work:
switch off device
Wait until the cutting blade has come to
a stop
Pull off the safety key and remove the
batteries
Wear protective gloves in the area of the
cutting blades during maintenance and
cleaning work to avoid possible injuries.
Maintenance and cleaning activities beyond those described in
this chapter may only be performed by customer service.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
To make sure that the device is in a safe condition regularly
check the device for apparent defects such as
loose fastening elements (nuts, bolts, screws),
grass catcher for wear or damaged parts
worn or damaged components and replace them for safety
reasons
Maintenance
Blade replacement
The cutting blades can be moved even
when the power source is switched off.
Wear protective gloves when working with
the blades. Risk of injury!
Worn blades reduce the performance of the device and put
excessive strain on the motor. Therefore check the condition of
the blades before each use. If necessary, have the blades
sharpened by an expert or replace them with new ones.
Secure the cutting blade against twisting with a piece
of wood.
Loosen the fastening nut (19).

Chat with your Atika RMC 40-400 manual using AI

Get instant AI answers from your Atika RMC 40-400 manual

Ask anything about the Atika RMC 40-400. Answers come from this manual, with the pages they are based on.

RMC 40-400 Maintenance Schedule

Before each use
Check blade condition

Inspect cutting blades for wear or damage before every use. Worn blades reduce performance and strain the motor.

Show in the manual (page 19)
After each use
Clean the mower

Clean the device immediately after work. Remove grass from underside, blades, and vents using a cloth or brush. Do not use water jets.

Show in the manual (page 19)
Regularly
Check fasteners and safety devices

Regularly check for loose nuts, bolts, screws, and damaged parts like the grass catcher. Ensure all guards are properly attached.

Show in the manual (page 18)
Before long-term storage
Prepare for storage

Thoroughly clean the machine and treat metal moving parts with environmentally friendly oil to prevent corrosion. Never use grease.

Show in the manual (page 19)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend RMC 40-400?

Yes No

Frequently Asked Questions

A

No, the lithium-ion batteries and the charger are not part of the standard delivery. You must purchase them separately from your dealer or the manufacturer.

Is this answer helpful?

A

It is recommended not to operate the mower on wet grass. Wet conditions can clog the machine, reduce cutting quality, and increase safety risks.

Is this answer helpful?

A

Use the lever on the side of the mower. Slide it towards the rear wheel to increase height or towards the front wheel to decrease it. There are 7 positions available.

Is this answer helpful?

A

You should only use this mower on slopes with a gradient of less than 15 degrees. Always mow sideways across the slope, never up and down.

Is this answer helpful?

A

Check the blades before every use. Replace them if they are dull or damaged. Dull blades tear grass, causing yellowing, and strain the motor.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Eco-friendly cordless operation with no emissions
  • Adjustable cutting height with 7 different settings
  • Includes both grass catcher and mulching insert options
  • Soft-start function protects the motor and battery
  • Compact design allows handlebars to fold for storage
VS

Disadvantages

  • Battery and charger are not included in the package
  • Requires separate purchase of compatible Li-Ion batteries
  • Not suitable for wet grass or very steep slopes
  • Motor may struggle if grass is too long or dense
  • Blade replacement requires specific tools and caution
M: QW-35-FL

Product Specification

Type

Lawn mower

Battery

36V, Li-Ion

Cutting width

15.75 inches

Cutting height

0.98-2.95 inches, adjustable, 7 levels

Grass collection volume

15.85 gallons

Features

Mulching function, side discharge, rear discharge, fill level indicator

Noise emission

94dB(A)

Weight

48.50 lbs

Delivery scope

without charger and battery

M: QW-35-FL

Product Description

Atika RMC 40-400 Battery Lawn Mower Solo: A Comprehensive Guide

The Atika RMC 40-400 Battery Lawn Mower Solo represents a significant step forward in home gardening efficiency. Designed for private gardens and hobby lawns, this cordless machine offers the freedom of movement without the hassle of cables or fuel. While the battery and charger are sold separately, the mower itself is ready to accept up to two lithium-ion batteries, providing flexible power options for various lawn sizes.

Operating this device requires careful attention to safety and proper assembly. The unit comes with essential accessories like a grass catcher and a mulching insert, allowing users to choose between collecting clippings or returning nutrients to the soil. The cutting height is easily adjustable across seven levels, ranging from 2.5 cm to 7.5 cm, ensuring a perfect cut for decorative, regular, or shade lawns. Safety features include a soft-start function, a safety key that must be inserted between batteries, and an automatic shut-off when the battery charge is low.

Maintenance is straightforward but critical for longevity. Users must regularly check blade sharpness, clean the underside of the mower, and ensure all fasteners are tight. It is important to never use solvents or high-pressure water for cleaning. Always remove the batteries before performing any maintenance tasks. The mower complies with European safety standards and should be disposed of according to local electronic waste regulations. By following the manual instructions regarding noise restrictions and safe operating practices, owners can enjoy a quiet and efficient mowing experience.

M: QW-35-FL

© Copyright 2026 Manual.ly