Manual.ly Logo

Atika KSHC 40-20 Manual

0.0 · 0 Ratings

PDF manual · 128 Pages

English

M: QW-35-FL
page

/ 128

Loading...
578b349f1f6e4faf9d4b54cf6422ec767513 page 9
9
Eco-Modus
Das Gerät kann im Energiesparmodus oder im
Powermodus betrieben werden.
Das Gerät startet immer im Normalmodus.
M
M
o
o
d
d
u
u
s
s
e
e
i
i
n
n
s
s
t
t
e
e
l
l
l
l
e
e
n
n
Drücken Sie die grüne Taste: Das Gerät läuft im Ener-
giesparmodus.
Die mittlere Anzeige leuchtet grün.
Die Akkulauflzeit ist höher.
Drücken Sie die gelbe Taste: Das Gerät läuft im Nor-
malmodus.
Die Akkulaufleistung verringert sich.
Sägekette
Vor dem Überprüfen/Spannen der Sägekette
- schalten Sie den Hochentaster aus
- nehmen Sie den Akku heraus
- Tragen Sie Schutzhandschuhe, um Verlet-
zungen zu vermeiden.
Überprüfen Sie die Sägekettenspannung
vor Arbeitsbeginn
nach den ersten Schnitten
während des Sägens regelmäßig alle 10 Minuten
Nur mit einer richtig gespannten Sägekette und einer
ausreichenden Schmierung haben Sie Einfluss auf die
Lebensdauer.
Bitte beachten Sie folgendes:
eine neue Sägekette muss öfters nachgespannt werden
bei Erwärmung der Kette auf Betriebstemperatur dehnt sie
sich aus und muss nachgespannt werden.
Nach Beendigung der Sägearbeiten die Sägekette wie-
der entspannen, denn bei Abkühlung würden sonst zu hohe
Spannungen in der Sägekette entstehen.
flattert die Kette oder tritt sie aus der Führung heraus, sofort
nachspannen.
S
S
ä
ä
g
g
e
e
k
k
e
e
t
t
t
t
e
e
s
s
p
p
a
a
n
n
n
n
e
e
n
n
Legen Sie den Hochentaster wie abgebildeet auf eine ge-
rade Fläche.
Klappen Sie den Griff (3a) hoch und lösen Sie die Befesti-
gungsschraube (3). Drehen Sie 1 – 2 Umdrehungen ge-
gen den Uhrzeigersinn.
Drehen Sie den Kettenspannring (4) schrittweise im Uhr-
zeigersinn bis die richtige Kettenspannung erreicht ist.
Die befestigungsschraube (3) dreht sich mit, eventuell
muss sie während des Spannvorganges wieder gelöst
werden.
Die Sägekette ist richtig gespannt, wenn sie in der Mitte
des Schwertes um ca. 3-4 mm angehoben werden kann.
Drehen sie den Kettespannring (4) gegen den Uhrzeiger-
sinn, wenn die Sägekette zu stark gespannt ist. Prüfen
Sie, ob die Kettenglieder richtig im Führungsschlitz der
Führungsschiene liegen.
Ziehen Sie die Befestigungsschraube wieder fest.
Prüfen der Kettenschmierung (Öl-Automatik)
Benutzen Sie nie den Hochentaster ohne funktionie
rende Kettenschmierung.
Sie überprüfen die Funktion der automatischen Ketten-
schmierung, indem Sie den Hochentaster einschalten und
ihn mit der Spitze in Richtung eines Kartons oder Papiers
auf dem Boden halten.
P
P
r
r
ü
ü
f
f
e
e
n
n
d
d
e
e
r
r
K
K
e
e
t
t
t
t
e
e
n
n
s
s
c
c
h
h
m
m
i
i
e
e
r
r
u
u
n
n
g
g
Berühren Sie den Boden nicht mit der Kette. Sicherheits
abstand von 20 cm einhalten.
Zeigt sich beim Überprüfen eine zunehmende Ölspur, ar-
beitet die Öl-Automatik einwandfrei.
Zeigt sich trotz vollem Öltank keine Ölspur
Reinigen Sie die obere Kettenspannbohrung (C) und
den Ölflusskanal (D)
Achten Sie beim Zusammenbau darauf, dass die
Dichtung (20) für den Ölflusskanal eingesetzt ist.
Sollte dies zu keinem Erfolg führen, wenden Sie sich bitte
an den Kundendienst.
Tragegurt
Legen Sie während des Arbeitens mit dem Gerät
immer den Tragegurt (4) an. Nur mit dem Tragegurt
haben Sie das Gerät beim Arbeiten unter Kontrolle.
A
A
n
n
l
l
e
e
g
g
e
e
n
n
d
d
e
e
s
s
T
T
r
r
a
a
g
g
e
e
g
g
u
u
r
r
t
t
e
e
s
s
Legen Sie den Gurt (15) über die Schulter und stellen sie
die Gurtlänge so ein, dass sich die Gurtbefestigung (E) auf
Höhe Ihrer Hüfte befindet.
Stellen Sie den Tragegurt so ein, dass ein angenehmes
und sicheres Tragen des Gerätes garantiert ist.
Ein beschädigter Tragegurt muss sofort aus-
getauscht werden.
S
S
c
c
h
h
n
n
e
e
l
l
l
l
v
v
e
e
r
r
s
s
c
c
h
h
l
l
u
u
s
s
s
s
l
l
ö
ö
s
s
e
e
n
n
Am Tragegurt befindet sich ein leicht erreichbarer Schnellver-
schluss (F). Dieser stellt im Gefahrenfall sicher, dass Sie die
Maschine schnell vom Tragegurt lösen können.
Um die Verbindung zu lösen, ziehen Sie ruckartig am
Gurtstück (G) des Schnellverschlusses.

Chat with your Atika KSHC 40-20 manual using AI

Get instant AI answers from your Atika KSHC 40-20 manual

Ask anything about the Atika KSHC 40-20. Answers come from this manual, with the pages they are based on.

KSHC 40-20 Maintenance Schedule

Every 10 minutes
Check saw chain tension

During sawing, check the chain tension regularly every 10 minutes. Re-tension if the chain flatters or comes out of the guide.

Before each use
Inspect machine condition

Before starting work, check that the pruner is assembled correctly, in good condition, oil tank filled, and chain sharp/tight.

Show in the manual (page 10)
Regularly
Check oil level

Check the oil level regularly during operation. Refill immediately if it shows 'MIN' to prevent dry running.

Show in the manual (page 10)
After each use
Clean the power pruner

Clean the housing with a soft brush or dry cloth after every use. Ensure ventilation slots are free for motor cooling.

Show in the manual (page 12)
Every 1-3 hours
Deep clean internal parts

After longer operation (1-3 hours), remove cover, guide bar, and chain to clean them with a brush.

Show in the manual (page 12)
Regularly
Inspect chain wheel teeth

Regularly check the teeth of the chain wheel for wear or damage. Replace immediately if worn to protect the chain.

Show in the manual (page 12)
Regularly
Clean guide bar components

Regularly inspect and clean the chain tensioner, tensioning bore, and oil discharge opening of the guide rail.

Show in the manual (page 12)
After each sharpening/change
Flip the guide bar

Turn the guide bar around after each chain change or sharpening to avoid uneven wear on one side.

Show in the manual (page 12)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KSHC 40-20?

Yes No

Frequently Asked Questions

A

The pruner works with 36V Li-Ion batteries, specifically the AP 40-2000 (2000 mAh) and AP 40-4000 (4000 mAh). Note that these batteries and the ALG 40-1800 charger are sold separately.

Is this answer helpful?

A

No, the Atika KSHC 40-20 is designed only for cutting branches on standing trees. It is not intended for felling trees, cutting saplings, shrubs, or building materials.

Is this answer helpful?

A

Switch on the pruner and hold the tip towards a piece of cardboard or paper at a safe distance. If an oil track appears on the surface, the automatic lubrication is functioning correctly.

Is this answer helpful?

A

Absolutely not. The manual strictly forbids operating the device on ladders, scaffolding, or trees due to the high risk of losing balance and control.

Is this answer helpful?

A

To protect breeding birds, pruning is prohibited between March 1st and September 30th. Always check local regulations regarding specific protected periods.

Is this answer helpful?

A

Immediately switch off the device and remove the battery. Use a wedge to free the guide bar. Never try to pull the pruner out while the chain is running.

Is this answer helpful?

A

Sharpen the chain when it produces sawdust instead of shavings or when you have to push the pruner hard through wood. A dull chain increases kickback risk.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Cordless operation provides mobility and ease of use in the garden
  • Eco-mode helps extend battery life during light pruning tasks
  • Automatic chain lubrication reduces maintenance effort and protects the chain
  • Telescopic shaft reaches high branches safely without ladders
  • Includes comprehensive safety features like locks and quick-release straps
VS

Disadvantages

  • Battery and charger are not included in the standard package
  • Not suitable for professional forestry work or large-scale operations
  • Requires regular maintenance like sharpening and tension checks
  • Cannot be used on unstable surfaces or near overhead power lines
  • Chain may require frequent tightening after initial use
M: QW-35-FL

Product Specification

Type

Telescopic Pole Saw

Battery

36V, Li-Ion

Bar Length

8.07 in

Chain Speed

23 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

1.69 fl oz

Features

Softgrip, Additional Handle, Brushless Motor, Telescopic, Overload Protection, Tool-Free Chain Tensioning, Automatic Chain Lubrication

Vibration Level

2.79 ft/s²

Sound Power Level

92 dB(A)

Weight

8.16 lbs

Package Contents

Without charger and battery, includes bar cover, carrying strap

M: QW-35-FL

Product Description

Mastering Garden Maintenance with the Atika KSHC 40-20

The Atika KSHC 40-20 Akku-Hochentaster solo is a powerful and versatile pole pruner designed specifically for private garden use. This electric tool allows homeowners to reach high branches on standing trees without the need for ladders, ensuring safety and efficiency during tree care tasks. The device features a telescopic shaft that can be extended to various lengths, making it ideal for trimming hedges, fruit trees, and ornamental plants in your backyard.

Operating on a 36-volt lithium-ion battery system, this pruner offers cordless freedom. Although the battery and charger are sold separately, the unit is compatible with AP 40-2000 and AP 40-4000 models, providing flexible runtime options depending on your needs. The tool includes an eco-mode switch, allowing users to conserve battery life when full power is not required. The automatic chain lubrication system ensures the saw chain remains properly oiled during operation, extending the life of the blade and guide bar.

Safety is a paramount concern with the KSHC 40-20. The manual emphasizes strict adherence to safety protocols, including wearing protective gear such as helmets, eye protection, and gloves. Users must maintain a safe distance from overhead power lines and avoid operating the machine in wet conditions or on unstable surfaces like ladders. The device also features a safety lock mechanism to prevent accidental starting, along with a quick-release strap for emergency situations.

Proper assembly and maintenance are crucial for optimal performance. The kit includes the front unit, two shaft sections, a guide bar, saw chain, and carrying strap. Regular cleaning, sharpening of the chain, and checking tension are necessary to prevent kickback and ensure smooth cutting. By following the detailed instructions provided, users can enjoy years of reliable service while keeping their gardens looking pristine.

Important Notes

  • Always wear appropriate personal protective equipment before starting work.
  • Do not use the pruner for felling trees or cutting non-wood materials.
  • Ensure the chain is sharp and correctly tensioned to avoid accidents.
  • Store the device in a dry place and remove the battery for long-term storage.
M: QW-35-FL

© Copyright 2026 Manual.ly