Manual.ly Logo

Atika KSHC 40-20 Manual

0.0 · 0 Ratings

PDF manual · 128 Pages

English

M: QW-35-FL
page

/ 128

Loading...
578b349f1f6e4faf9d4b54cf6422ec767513 page c
12
S
S
c
c
h
h
ä
ä
r
r
f
f
e
e
n
n
d
d
e
e
r
r
S
S
ä
ä
g
g
e
e
k
k
e
e
t
t
t
t
e
e
Nur
mit einer scharfen und sauberen Sägekette
können Sie sicher und gut arbeiten. Beschädigte
oder falsch geschärfte Sägeketten erhöhen die
Rückschlaggefahr!
Eine Sägekette muss geschärft werden, wenn
anstatt Sägespäne nur noch Holzstaub ausgeworfen wird
der Hochentaster während des Schneidens durch das Holz
gedrückt werden muss.
Für den unerfahrenen Benutzer: Lassen Sie die Sägekette
von einem Fachmann/Kundendienst schärfen.
Sie können Ihre Sägekette aber auch mit unseren Ketten-
schärfgeräten KSG 104 (Artikel-Nr.: 302230) oder KSG 220 A
(Artikel-Nr.: 302360) selbst schärfen.
Sägekettentyp CL 14333 X
Tiefenbegrenzerabstand T 0,51 mm (.50“)
Schärfwinkel α 50°
Brustwinkel β 80°
Feilhaltewinkel 90°
K
K
e
e
t
t
t
t
e
e
n
n
r
r
a
a
d
d
Die Beanspruchung des Kettenrades (24) ist besonders groß.
Überprüfen Sie die Zähne des Kettenrades regelmäßig auf
Abnutzung oder Beschädigung.
Ein abgenutztes oder beschädigtes Kettenrad ver-
mindert die Lebensdauer der Sägekette und sollte
deswegen unverzüglich vom Kundendienst ausge-
tauscht werden.
Reinigung
Reinigen Sie den Hochentaster sorgfältig nach jedem Ge-
brauch, damit die einwandfreie Funktion erhalten bleibt.
Reinigen Sie das Gehäuse mit einer weichen Bürste oder
einem trockenen Lappen.
Wasser, Lösungsmittel und Poliermittel dürfen nicht
verwendet werden.
Achten Sie darauf, dass die Lüftungsschlitze für die
Motorkühlung frei sind (Gefahr der Überhitzung).
Demontieren Sie nach längerer Einsatzdauer (1 – 3 Stun-
den) die Abdeckung (5), die Führungsschiene (1) und die
Kette (2) und reinigen Sie sie mit einer Bürste.
Säubern Sie die Sägekette bei starker Verschmutzung mit
einem handelsüblichen Kettenreiniger.
Befreien Sie das Kettenrad (24) und die Führungsschie-
nenaufnahmen (a) mit einer Bürste von allen Anhaftungen.
Säubern Sie den Ölflusskanal (20) mit einem sauberen
Lappen oder einem Pinsel.
Achten Sie beim Zusammenbau darauf, dass die
Dichtung (10) für den Ölflusskanal eingesetzt ist.
R
R
e
e
i
i
n
n
i
i
g
g
e
e
n
n
d
d
e
e
r
r
F
F
ü
ü
h
h
r
r
u
u
n
n
g
g
s
s
s
s
c
c
h
h
i
i
e
e
n
n
e
e
Kontrollieren und reinigen Sie regelmäßig
den Kettenspanner (20) und Kettenspannbohrung (A)
die Ölaustrittöffnung (A) der Führungsschiene
Entfernen Sie Grat, der sich gebildet hat, mit einer Flach-
feile und Schleifleinen.
Wenden Sie die Führungsschiene nach jedem Ketten-
wechsel / Kettenschärfen, um eine einseitige Abnutzung
zu vermeiden.
Tansport
Vor jedem Transport Gerät ausschalten und
Akku entnehmen.
Transportieren Sie den Hochentaster nur mit aufge-
stecktem Kettenschutz.
Weitere Informationen zu den Akkus und dem Ladegerät
entnehmen Sie bitte den jeweiligen „Betriebsanleitungen“.
Lagerung
Bewahren Sie unbenutzte Geräte an einem trockenen, ver-
schlossenen Ort, der vor Frost geschützt ist, außerhalb der
Reichweite von Kindern und unbefugter Personen auf.
Beachten Sie vor einer längeren Lagerung folgendes, um die
Lebensdauer des Hochentasters zu verlängern und ein
leichtgängiges Bedienen zu gewährleisten:
Entnehmen Sie den Akku
Führen Sie eine gründliche Reinigung durch.
Entfernen Sie das Öl aus dem Öltank.
: Einige Kettenöle neigen nach längerer Zeit zur Verkrus-
tung. Deswegen sollte das Ölsystem vor einer länge-
ren Lagerung mit einem handelsüblichen Kettensägen-
reiniger durchgespült werden. Füllen Sie den Reiniger
bis zur Hälfte (ca. 50 ml) in den Öltank. Verschließen
Sie den Tank. Schalten Sie den Hochentaster ohne
montierte Führungsschiene und Kette solange ein, bis
der ganze Reiniger aus der Ölöffnung des Hochentas-
ters ausgetreten ist.
Legen Sie die Sägekette nach dem Reinigen
kurz
in ein Ölbad und wickeln sie anschließend
in ein Ölpa-
pier.
Stecken Sie den Kettenschutz auf.
Weitere Informationen zu den Akkus und dem Ladegerät
entnehmen Sie bitte den jeweiligen „Betriebsanleitungen“.
Garantie
Bitte beachten Sie die beiliegende Garantieerklärung.

Chat with your Atika KSHC 40-20 manual using AI

Get instant AI answers from your Atika KSHC 40-20 manual

Ask anything about the Atika KSHC 40-20. Answers come from this manual, with the pages they are based on.

KSHC 40-20 Maintenance Schedule

Every 10 minutes
Check saw chain tension

During sawing, check the chain tension regularly every 10 minutes. Re-tension if the chain flatters or comes out of the guide.

Before each use
Inspect machine condition

Before starting work, check that the pruner is assembled correctly, in good condition, oil tank filled, and chain sharp/tight.

Show in the manual (page 10)
Regularly
Check oil level

Check the oil level regularly during operation. Refill immediately if it shows 'MIN' to prevent dry running.

Show in the manual (page 10)
After each use
Clean the power pruner

Clean the housing with a soft brush or dry cloth after every use. Ensure ventilation slots are free for motor cooling.

Show in the manual (page 12)
Every 1-3 hours
Deep clean internal parts

After longer operation (1-3 hours), remove cover, guide bar, and chain to clean them with a brush.

Show in the manual (page 12)
Regularly
Inspect chain wheel teeth

Regularly check the teeth of the chain wheel for wear or damage. Replace immediately if worn to protect the chain.

Show in the manual (page 12)
Regularly
Clean guide bar components

Regularly inspect and clean the chain tensioner, tensioning bore, and oil discharge opening of the guide rail.

Show in the manual (page 12)
After each sharpening/change
Flip the guide bar

Turn the guide bar around after each chain change or sharpening to avoid uneven wear on one side.

Show in the manual (page 12)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KSHC 40-20?

Yes No

Frequently Asked Questions

A

The pruner works with 36V Li-Ion batteries, specifically the AP 40-2000 (2000 mAh) and AP 40-4000 (4000 mAh). Note that these batteries and the ALG 40-1800 charger are sold separately.

Is this answer helpful?

A

No, the Atika KSHC 40-20 is designed only for cutting branches on standing trees. It is not intended for felling trees, cutting saplings, shrubs, or building materials.

Is this answer helpful?

A

Switch on the pruner and hold the tip towards a piece of cardboard or paper at a safe distance. If an oil track appears on the surface, the automatic lubrication is functioning correctly.

Is this answer helpful?

A

Absolutely not. The manual strictly forbids operating the device on ladders, scaffolding, or trees due to the high risk of losing balance and control.

Is this answer helpful?

A

To protect breeding birds, pruning is prohibited between March 1st and September 30th. Always check local regulations regarding specific protected periods.

Is this answer helpful?

A

Immediately switch off the device and remove the battery. Use a wedge to free the guide bar. Never try to pull the pruner out while the chain is running.

Is this answer helpful?

A

Sharpen the chain when it produces sawdust instead of shavings or when you have to push the pruner hard through wood. A dull chain increases kickback risk.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Cordless operation provides mobility and ease of use in the garden
  • Eco-mode helps extend battery life during light pruning tasks
  • Automatic chain lubrication reduces maintenance effort and protects the chain
  • Telescopic shaft reaches high branches safely without ladders
  • Includes comprehensive safety features like locks and quick-release straps
VS

Disadvantages

  • Battery and charger are not included in the standard package
  • Not suitable for professional forestry work or large-scale operations
  • Requires regular maintenance like sharpening and tension checks
  • Cannot be used on unstable surfaces or near overhead power lines
  • Chain may require frequent tightening after initial use
M: QW-35-FL

Product Specification

Type

Telescopic Pole Saw

Battery

36V, Li-Ion

Bar Length

8.07 in

Chain Speed

23 ft/s

Chain Pitch

3/8"

Oil Tank Capacity

1.69 fl oz

Features

Softgrip, Additional Handle, Brushless Motor, Telescopic, Overload Protection, Tool-Free Chain Tensioning, Automatic Chain Lubrication

Vibration Level

2.79 ft/s²

Sound Power Level

92 dB(A)

Weight

8.16 lbs

Package Contents

Without charger and battery, includes bar cover, carrying strap

M: QW-35-FL

Product Description

Mastering Garden Maintenance with the Atika KSHC 40-20

The Atika KSHC 40-20 Akku-Hochentaster solo is a powerful and versatile pole pruner designed specifically for private garden use. This electric tool allows homeowners to reach high branches on standing trees without the need for ladders, ensuring safety and efficiency during tree care tasks. The device features a telescopic shaft that can be extended to various lengths, making it ideal for trimming hedges, fruit trees, and ornamental plants in your backyard.

Operating on a 36-volt lithium-ion battery system, this pruner offers cordless freedom. Although the battery and charger are sold separately, the unit is compatible with AP 40-2000 and AP 40-4000 models, providing flexible runtime options depending on your needs. The tool includes an eco-mode switch, allowing users to conserve battery life when full power is not required. The automatic chain lubrication system ensures the saw chain remains properly oiled during operation, extending the life of the blade and guide bar.

Safety is a paramount concern with the KSHC 40-20. The manual emphasizes strict adherence to safety protocols, including wearing protective gear such as helmets, eye protection, and gloves. Users must maintain a safe distance from overhead power lines and avoid operating the machine in wet conditions or on unstable surfaces like ladders. The device also features a safety lock mechanism to prevent accidental starting, along with a quick-release strap for emergency situations.

Proper assembly and maintenance are crucial for optimal performance. The kit includes the front unit, two shaft sections, a guide bar, saw chain, and carrying strap. Regular cleaning, sharpening of the chain, and checking tension are necessary to prevent kickback and ensure smooth cutting. By following the detailed instructions provided, users can enjoy years of reliable service while keeping their gardens looking pristine.

Important Notes

  • Always wear appropriate personal protective equipment before starting work.
  • Do not use the pruner for felling trees or cutting non-wood materials.
  • Ensure the chain is sharp and correctly tensioned to avoid accidents.
  • Store the device in a dry place and remove the battery for long-term storage.
M: QW-35-FL

© Copyright 2026 Manual.ly