Manual.ly Logo

Atika KSC 40-35 Manual

0.0 · 0 Ratings

PDF manual · 140 Pages

English

M: QW-35-FL
page

/ 140

Loading...
77adf4786ef63ff361f78a68e24728675707 page 9
9
Laden Sie den Li-Ionen Akku auf (Betriebsanlei-
tung „Akku“).
A
A
u
u
s
s
s
s
c
c
h
h
a
a
l
l
t
t
e
e
n
n
Ein-/Ausschalter (9) loslassen..
Eco-Modus
Das Gerät kann im Energiesparmodus oder
im Powermodus betrieben werden.
Das Gerät startet immer im Normalmodus.
M
M
o
o
d
d
u
u
s
s
e
e
i
i
n
n
s
s
t
t
e
e
l
l
l
l
e
e
n
n
Drücken Sie die grüne Taste: Das Gerät läuft im Ener-
giesparmodus.
Die mittlere Anzeige leuchtet grün.
Die Akkulaufzeit ist höher.
Drücken Sie die gelbe Taste: Das Gerät läuft im Nor-
malmodus.
Die Akkulaufleistung verringert sich.
Kettenbremse
Die Kettenbremse ist ein Schutzmechanismus, der bei
zurückschlagender Kettensäge über den vorderen Hand-
schutz ausgelöst wird nach Loslassen des Ein/Aus-
Schalters ausgelöst wird. Die Sägekette stoppt umgehend
(<0,1 Sek.).
Prüfen der Kettenbremse
Prüfen Sie vor jedem Arbeitsbeginn die Funktion der
Kettenbremse.
Kettensäge einschalten.
Halten Sie die Kettensäge mit beiden Händen fest.
Drücken Sie mit dem Handrücken
gegen den vorderen Handschutz (14).
Die Sägekette muss sofort stehen bleiben!
Eine Kettensäge ohne Kettenbremsen-Funktion
darf nicht benutzt werden. Bitte wenden Sie sich
an den Hersteller oder Kundendienst!
Sägekette
Vor dem Übertprüfen/Spannen der Sägekette
- schalten Sie die Kettensäge aus
- legen Sie die Kettenbremse ein
- nehmen Sie den Akku heraus
Überprüfen Sie die Sägekettenspannung
vor Arbeitsbeginn
nach den ersten Schnitten
während des Sägens regelmäßig alle 10 Minuten
Nur mit einer richtig gespannten Sägekette und einer aus-
reichenden Schmierung haben Sie Einfluss auf die Lebensdau-
er.
Bitte beachten Sie Folgendes:
eine neue Sägekette muss öfters nachgespannt werden, bis
sie sich gelängt hat.
bei Erwärmung der Kette auf Betriebstemperatur dehnt sie
sich aus und muss nachgespannt werden.
Nach Beendigung der Sägearbeiten die Sägekette
wieder entspannen, denn bei Abkühlung würden sonst
zu hohe Spannungen in der Sägekette entstehen.
flattert die Kette oder tritt sie aus der Führung heraus, sofort
nachspannen.
S
S
p
p
a
a
n
n
n
n
e
e
n
n
d
d
e
e
r
r
S
S
ä
ä
g
g
e
e
k
k
e
e
t
t
t
t
e
e
Klappen Sie den Griff (3a) hoch und lösen Sie die Befesti-
gungsschraube (3). Drehen Sie 1 – 2 Umdrehungen ge-
gen den Uhrzeigersinn.
Drehen Sie den Kettenspannring (4) schrittweise im Uhr-
zeigersinn bis die richtige Kettenspannung erreicht ist. Der
Rasteffekt verhindert, dass sich die Kettenspannung löst.
Die Befestigungsschraube (11) dreht sich mit, eventu-
ell muss sie während des Spannvorganges wieder ge-
löst werden.
Die Sägekette ist richtig gespannt, wenn sie in der Mitte
der Führungsschiene um ca. 3 – 4 mm angehoben werden
kann.
Drehen Sie den Kettenspannring (4) gegen den Uhrzei-
gersinn, wenn die Sägekette zu stark gespannt ist.
Prüfen Sie, ob die Kettenglieder richtig im Führungsschlitz
der Führungsschiene liegen.
Ziehen Sie die Befestigungsschraube mit der Hand wieder
fest.
Kettenschmierung
Benutzen Sie nie die Kettensäge ohne funktionierende
Kettenschmierung.
Sie überprüfen die Funktion der automatischen Ketten-
schmierung, indem Sie die Kettensäge einschalten und sie
mit der Spitze in Richtung eines Kartons oder Papiers auf
dem Boden halten.
Prüfen der Kettenschmierung (Öl-Automatik)
Berühren Sie den Boden nicht mit der Kette. Sicher
heitsabstand von 20 cm einhalten.
Zeigt sich beim Überprüfen eine zunehmende Ölspur, ar-
beitet die Öl-Automatik einwandfrei.
Zeigt sich trotz vollem Öltank keine Ölspur
Reinigen Sie den Ölflusskanal (G) und
die obere Kettenspannbohrung (B).
Achten Sie beim Zusammenbau darauf, dass die
Dichtung (7) für den Ölflusskanal eingesetzt ist.
Sollte dies zu keinem Erfolg führen, wenden Sie sich bitte
an den Kundendienst.

Chat with your Atika KSC 40-35 manual using AI

Get instant AI answers from your Atika KSC 40-35 manual

Ask anything about the Atika KSC 40-35. Answers come from this manual, with the pages they are based on.

KSC 40-35 Maintenance Schedule

Before each use
Check the chain brake function

Start the saw and push against the front hand guard. The chain must stop immediately (

Every 10 minutes
Check and adjust saw chain tension

Regularly check tension during sawing. Adjust so the chain can be lifted approx. 3-4 mm in the middle of the guide bar.

After every use
Clean the chain saw

Clean the housing with a soft brush or dry cloth. Ensure ventilation slots are free. Do not use water or solvents.

Show in the manual (page 13)
After every chain change/sharpening
Turn the guide bar

Flip the guide bar to avoid single-side wearing.

Show in the manual (page 13)
Regularly
Inspect chain wheel for wear

Check teeth for wear or damage. Replace immediately via customer service if worn, as it reduces chain life.

Show in the manual (page 13)
Regularly
Clean guide bar oil opening and tensioner

Inspect and clean the oil discharge opening (A) and chain tensioner (6). Remove burrs with a flat file.

Show in the manual (page 13)
When dull
Sharpen the saw chain

Sharpen when only dust is ejected or pressure is needed. Use specified angles: Sharpening 30 deg, Breast 60 deg.

Show in the manual (page 13)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend KSC 40-35?

Yes No

Frequently Asked Questions

A

No, the KSC 40-35 is sold as a solo unit. You must purchase the AP 40-2000 or AP 40-4000 battery and the ALG 40-1800 charger separately to operate the chainsaw.

Is this answer helpful?

A

Absolutely not. This chainsaw is designed exclusively for cutting wood. Using it on masonry, plastic, or metal can damage the chain, cause dangerous kickbacks, and void the warranty.

Is this answer helpful?

A

With the saw off and the brake engaged, pull the chain up from the middle of the guide bar. It should lift about 3 to 4 mm. If it is too loose or tight, adjust the tension ring accordingly.

Is this answer helpful?

A

Eco mode conserves battery power by limiting speed, ideal for light pruning. Normal mode provides full power for heavier cutting but drains the battery faster.

Is this answer helpful?

A

No, operating a chainsaw from a ladder is extremely dangerous due to the risk of losing balance and control. Always stand on solid, level ground.

Is this answer helpful?

A

Sharpen the chain whenever it produces only dust instead of chips or if you have to force the saw through the wood. A dull chain increases the risk of kickback.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Lightweight design at approximately 3.5 kg makes it easy to handle for extended periods.
  • Automatic oil lubrication system reduces maintenance and protects the chain.
  • Eco-mode allows for longer battery runtime during low-intensity tasks.
  • Fast-acting chain brake stops the saw in under 0.1 seconds for enhanced safety.
VS

Disadvantages

  • Battery and charger are not included in the box and must be purchased separately.
  • Not suitable for professional forestry work or large-scale timber operations.
  • Chain requires frequent tensioning checks, especially when new or hot.
  • Limited cutting capacity due to the 14-inch guide bar size.
M: QW-35-FL

Product Specification

Type

Chainsaw

Battery

36V, Li-Ion

Bar Length

13.78in

Chain Speed

42.65ft/s

Chain Pitch

3/8"

Oil Tank Capacity

4.57fl oz

Features

Softgrip, Additional Handle, Brushless Motor, Overload Protection, Tool-Free Chain Tensioning, Automatic Chain Lubrication, Chain Brake, Chain Catcher, Guide Bar Stop

Vibration Level

6.14ft/s²

Sound Power Level

99dB(A)

Weight

7.72lbs

Package Contents

Without Charger and Battery, Includes Saw Bar (Oregon), Bar Cover

M: QW-35-FL

Product Description

The Atika KSC 40-35 Cordless Chainsaw Solo: A Powerful Garden Companion

The Atika KSC 40-35 Cordless Chainsaw solo is designed for homeowners and hobby gardeners who need a reliable tool for cutting wood without the hassle of fuel or cords. This lightweight unit features a 36-volt lithium-ion battery system, offering significant power for pruning branches, cutting firewood, and tackling small trees in your backyard. While the saw itself is included, users must note that the battery and charger are sold separately, allowing you to choose between the 2000 mAh or 4000 mAh options based on your project needs.

Equipped with a 14-inch guide bar and a 91P052X Oregon chain, this chainsaw delivers a maximum cutting length of 356 mm. The automatic oil lubrication system ensures the chain stays protected during operation, extending the life of both the chain and the guide bar. Safety is a top priority, featuring a robust chain brake that stops the blade in less than 0.1 seconds in case of kickback. The device also includes an eco-mode to maximize battery runtime when high power is not required.

Before using the saw, it is crucial to read all safety instructions carefully. The machine is intended strictly for private use in gardens and should never be used for forestry work or cutting non-wood materials like plastic or masonry. Proper personal protective equipment, including eye protection, hearing guards, and cut-resistant gloves, is mandatory. Always ensure the chain is correctly tensioned and sharp before starting any work to prevent accidents and ensure clean cuts.

Important Usage Notes

  • Never operate the saw above shoulder height to maintain control.
  • Always keep both hands on the handles while the chain is moving.
  • Do not use the saw on wet ground or during heavy rain.
  • Ensure the chain brake is engaged whenever the saw is not actively cutting.
  • Store the saw in a dry place away from children when not in use.
M: QW-35-FL

© Copyright 2026 Manual.ly