Manual.ly Logo

Atika HT315 Manual

0.0 · 0 Ratings

PDF manual · 182 Pages

English

M: QW-35-FL
page

/ 182

Loading...
ec87309f5646f83c746fb2d53406d197b2c3 page 10
14
The connector of the connection cable must be splash-proof.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
Check regularly the cable of the table saw and get possible
damages repaired by a professional specialist.
When running the connection line observe that it does not
interfere, is not squeezed, bent and the plug connection does
not get wet.
Regularly check the extension cables and replace them if they
are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or one
of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out by
the manufacturer or one of his customer service points.
Use only original spare. Accidents can arise for the user
through the use of other spare parts. The manufacturer is
not liable for any damage or injury resulting from such
action.
Preparing for startup
To achieve flawless functioning of the machine, please follow
the instructions listed:
• Place the machine at a location that meets the following
conditions:
− secured against slipping
− free of vibrations
− even
− free of tripping hazards
− adequate light
• Before each use, check
− Defective connecting lines (cracks, cuts, etc.).
Never use defective lines!
− the saw blade for flawless condition
• Do not use any cracked saw blades or such that have
changed their shape.
• Do not use saw blades made of high-speed steel.
• Always stand to the side of the danger zone (saw blade) when
working at the bench.
Start-up
Checking the safety devices
(before each starting)
− Proper working condition of the safety guard.
− Check the switch by turning it on and off.
− Do not use any device where the switch cannot be switched
on and off. Damaged switches must be repaired or replaced
immediately by the customer service.
− Brake
− The saw blade must stand still within 10 seconds after it was
switched off. The brake is defective if this time is exceeded.
The saw must then be repaired by the manufacturer or a
workshop appointed by the manufacturer.
− The push stick must be within easy reach.
⇒ Replace defective push sticks by new ones.
− Correct splitting wedge setting (see also Fig. 11).
Rotating direction of the saw blade
Ensure that the rotational direction of the saw blade is the
same as the rotational direction given on the guard (33).
The rotating direction of three-phase
motors can be changed by inserting a
screwdriver in the connector collar
provided for this purpose and turning
left or right while exerting a light
pressure to adjust the correct rotating
direction.
Selection of saw blades
⇒ Observe the splitting wedge thickness "S"; it is etched
into the side of the splitting wedge.
The splitting wedge must not be thinner than the saw
blade, and not thicker than the kerf width produced by the
blade.
The rating plate specifies maximum and minimum saw
blade diameters, as well as the hole diameter.
Do not use saw blades that are designed for a lower max.
speed (see identification on the saw blade) than the motor
speed (see the technical data).
Electric supply
Compare the voltage listed on the machine’s type plate, e.g.
230 V, with the mains voltage and connect the machine to a
suited and properly earthed electrical socket.
• Alternating-current motor:
Schuko (earthed) socket, mains voltage 230 V, with earth-
leakage circuit breaker (FI switch 30 mA).
• Three-phase motor:
CEE socket, 3-pin+N+PE, mains voltage 380 V or 400 V, with
earth-leakage circuit breaker (FI switch 30 mA).
Use an extension cable in compliance with IEC 60245 (H 07 RN-
F) having a core cross-section of at least:
⇒ 1.5 mm² for a cable length of up to 25 m.
⇒ 2.5 mm² for a cable length exceeding 25 m.
Main fuse
EU 16 A
UK 13 A

Chat with your Atika HT315 manual using AI

Get instant AI answers from your Atika HT315 manual

Ask anything about the Atika HT315. Answers come from this manual, with the pages they are based on.

HT315 Maintenance Schedule

Before each use
Check safety devices and saw blade condition

Verify guard, switch, brake, and splitting wedge. Check cable for damage and ensure saw blade is sharp, uncracked, and correctly mounted.

Show in the manual (page 16)
Regularly
Clean and oil all movable parts

Clean and oil all movable parts using sewing machine oil or spray oil. Never use grease. Keep handles dry and free of oil.

As needed
Clean motor cooling ribs

Clean the cooling ribs on the motor if heavily soiled to ensure adequate cooling and prevent overheating.

As needed
Remove resin from table and blade

Keep saw blade free of rust and resin. Remove resin residues from the table surface using a commercial maintenance spray.

After every blade change
Check splitting wedge adjustment

The setting of the splitting wedge must be checked after each saw blade change to ensure correct alignment.

Show in the manual (page 10)
Before long storage
Thorough cleaning and oiling

Perform a thorough cleaning and treat all movable parts with environmentally friendly oil before storing the machine for a longer period.

Show in the manual (page 10)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend HT315?

Yes No

Frequently Asked Questions

A

The maximum cutting depth is approximately 90 mm, allowing you to cut through thick timber and panels effectively.

Is this answer helpful?

A

No, you must not use HSS steel blades. They are too hard and brittle, posing a severe risk of breaking and causing injury. Only carbide-tipped blades are permitted.

Is this answer helpful?

A

You should check the brake function before every single use. The blade must come to a complete stop within 10 seconds after switching off the machine.

Is this answer helpful?

A

No, the saw must not be used in wet environments or exposed to rain. It is designed for indoor use in dry, well-lit workshops.

Is this answer helpful?

A

The saw accepts circular saw blades with a diameter between 300 mm and 315 mm and a bore hole size of 30 mm.

Is this answer helpful?

A

Only persons over the age of 18 who are familiar with the device and have read the instruction manual are permitted to operate the saw.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 3.0kW motor handles tough materials easily
  • Continuous adjustment for cutting depth and angle
  • Effective braking system stops blade in under 10 seconds
  • Large 800x550mm table supports big workpieces
  • Included push stick enhances safety for narrow cuts
VS

Disadvantages

  • Noise levels exceed safe limits without hearing protection
  • Heavy weight of 46 kg makes transport difficult
  • HSS steel blades are incompatible and dangerous
  • Dust extraction requires separate vacuum purchase
  • Assembly required upon delivery adds initial time
M: QW-35-FL

Product Specification

Type

Table Circular Saw

Power

3000W (230V)

No-load Speed

2730 rpm

Blade Diameter

12.4 inches

Cutting Capacity

3.54 inches (cutting depth at 0°), 2.48 inches (cutting depth at 45° tilt)

Bevel Angle

0-45°

Miter Cuts

0-45°

Features

Dust extraction, Tilt function

Dimensions

31.5x31.9x21.7 inches (WxDxH)

Weight

101.41 lbs

M: QW-35-FL

Product Description

The Atika HT315: A Powerful Companion for Your Workshop

The Atika HT315 230V 3.0kW Electric Table Circular Saw Manual represents a significant upgrade for woodworkers seeking precision and power in a compact package. This robust machine is designed specifically for cutting solid wood and panel materials like chipboard, MDF, and plywood with square or rectangular cross-sections. Powered by a high-performance 3.0kW motor, it delivers the torque necessary to handle demanding cuts while maintaining smooth operation.

Safety is at the forefront of the design. The saw features a protective guard, a splitting wedge, and a reliable brake system that stops the blade within ten seconds of disengagement. Users are reminded that proper personal protective equipment, including ear protection and safety goggles, is essential during operation due to noise levels reaching up to 90.9 dB(A) under load. The machine also includes a dust extraction port compatible with standard vacuum systems to maintain a clean working environment.

Versatility is another key strength. The table dimensions of 800 x 550 mm provide ample space for large workpieces, while the continuous height and bevel adjustments allow for precise cuts up to 90 mm deep at angles up to 45 degrees. The inclusion of a push stick and adjustable fences ensures accurate rip and cross cuts, making it suitable for both professional joinery and serious DIY projects.

Maintenance is straightforward but requires diligence. Regular cleaning of resin buildup and oiling of moving parts without using grease will extend the lifespan of the unit. It is crucial to use only carbide-tipped blades within the specified diameter range of 300 to 315 mm, as HSS steel blades are strictly prohibited due to the risk of shattering.

Important Notes

  • Always ensure the machine is unplugged before changing blades or performing maintenance.
  • Do not operate the saw in wet conditions or near flammable liquids.
  • Children under 18 are strictly prohibited from operating this equipment.
M: QW-35-FL

© Copyright 2026 Manual.ly