Manual.ly Logo

Atika HT315 Manual

0.0 · 0 Ratings

PDF manual · 182 Pages

English

M: QW-35-FL
page

/ 182

Loading...
ec87309f5646f83c746fb2d53406d197b2c3 page d
11
You may not start to operate the machine until
you have read this instruction manual, observed
all the instructions given and installed the machine as
described!
Keep the instructions in a safe place for future use.
Contents
Extent of delivery 11
Characteristic noise values 11
Operating times 11
Symbols on the machine 11
Symbols of the instructions manual 11
Proper use 12
Residual risks 12
Safety instructions 12
Preparing for startup 14
Start-up 14
Working with the saw 15
Maintenance and cleaning 16
− Exchange of saw blade 16
Transport 17
Storage 17
Possible faults 18
Technical data 18
Guarantee 19
EC Declaration of Conformity 177
Manufacturer proof 180
Spare part list (Assembly instructions)
Extent of delivery
• Circular Saw Bench (unmounted)
• Fastener bag
• Accessories bag
• Accessories bag for sticker
• Assembly accessories for saw blade change
• Original instructions
• Assembly instructions
• Pushstick
Please refer to the enclosed assembly instructions for a detailed
list of the extent of delivery.
After unpacking, check the contents of the box for
¾ completeness
¾ possible transport damage.
Report any damage or missing items to your dealer, supplier or
the manufacturer immediately. Complaints made at a later date
will not be acknowledged.
Characteristic noise values
Application of the machine as table saw with standard saw blade.
The factor of measurement uncertainty is K = 4 dB.
Sound power level according DIN EN ISO 3746
Sound power level Guaranteed sound power
level
No-load L
WA
= 80.6 dB(A)
L
WA
= 105 dB(A)
Load L
WA
= 104.6 dB(A)
Sound pressure level at the workplace
according DIN EN ISO 11202
No-load L
PA
= 80.5 dB(A)
Load L
PA
= 90.9 dB(A)
The values given are emission values and must therefore not simultaneously
represent safe workplace values too. Although there is a relationship between
emission and immersion levels, it can be reliably deduced whether additional
precautionary measures are necessary or not. Factors, which can influence the
immision level currently existing at the workplace include the duration of the
effects, the special type of the workroom, other noise sources, etc. e.g. the
number of machines and other adjacent processes. The permissible workplace
values can also vary from country to country. This information should however
enable carrying out an improved assessment of the danger and risk.
Operating times
Please observe as well the regional regulations for noise
protection.
Symbols of the machine
Protective guard, splitting
wedge and saw blade o.k.?
Stoppers ready for running
and push stick ready to hand?
Working place tidied?
Carefully read the instructions manual and the
safety instructions before starting the machine
and observe the instructions when operating.
Wear ear
protection!
Cutting depth
adjustment
Electrical devices do not go into the domestic rubbish.
Give devices, accessories and packaging to an
ecofriendly recycling.
According to the European Directive 2012/19/EU on electrical
and electronic scrap, electrical devices that are no longer
serviceable must be separately collected and brought to a facility
for environmentally compatible recycling.
This product complies with European regulations
specifically applicable to it.
Symbols of the instructions manual
Potential hazard or hazardous situation. Failure to
observe these instructions may lead to injuries or cause
damage to property.
Important information on proper handling. Failure to
observe these instructions may lead to malfunction.

Chat with your Atika HT315 manual using AI

Get instant AI answers from your Atika HT315 manual

Ask anything about the Atika HT315. Answers come from this manual, with the pages they are based on.

HT315 Maintenance Schedule

Before each use
Check safety devices and saw blade condition

Verify guard, switch, brake, and splitting wedge. Check cable for damage and ensure saw blade is sharp, uncracked, and correctly mounted.

Show in the manual (page 16)
Regularly
Clean and oil all movable parts

Clean and oil all movable parts using sewing machine oil or spray oil. Never use grease. Keep handles dry and free of oil.

As needed
Clean motor cooling ribs

Clean the cooling ribs on the motor if heavily soiled to ensure adequate cooling and prevent overheating.

As needed
Remove resin from table and blade

Keep saw blade free of rust and resin. Remove resin residues from the table surface using a commercial maintenance spray.

After every blade change
Check splitting wedge adjustment

The setting of the splitting wedge must be checked after each saw blade change to ensure correct alignment.

Show in the manual (page 10)
Before long storage
Thorough cleaning and oiling

Perform a thorough cleaning and treat all movable parts with environmentally friendly oil before storing the machine for a longer period.

Show in the manual (page 10)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend HT315?

Yes No

Frequently Asked Questions

A

The maximum cutting depth is approximately 90 mm, allowing you to cut through thick timber and panels effectively.

Is this answer helpful?

A

No, you must not use HSS steel blades. They are too hard and brittle, posing a severe risk of breaking and causing injury. Only carbide-tipped blades are permitted.

Is this answer helpful?

A

You should check the brake function before every single use. The blade must come to a complete stop within 10 seconds after switching off the machine.

Is this answer helpful?

A

No, the saw must not be used in wet environments or exposed to rain. It is designed for indoor use in dry, well-lit workshops.

Is this answer helpful?

A

The saw accepts circular saw blades with a diameter between 300 mm and 315 mm and a bore hole size of 30 mm.

Is this answer helpful?

A

Only persons over the age of 18 who are familiar with the device and have read the instruction manual are permitted to operate the saw.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Powerful 3.0kW motor handles tough materials easily
  • Continuous adjustment for cutting depth and angle
  • Effective braking system stops blade in under 10 seconds
  • Large 800x550mm table supports big workpieces
  • Included push stick enhances safety for narrow cuts
VS

Disadvantages

  • Noise levels exceed safe limits without hearing protection
  • Heavy weight of 46 kg makes transport difficult
  • HSS steel blades are incompatible and dangerous
  • Dust extraction requires separate vacuum purchase
  • Assembly required upon delivery adds initial time
M: QW-35-FL

Product Specification

Type

Table Circular Saw

Power

3000W (230V)

No-load Speed

2730 rpm

Blade Diameter

12.4 inches

Cutting Capacity

3.54 inches (cutting depth at 0°), 2.48 inches (cutting depth at 45° tilt)

Bevel Angle

0-45°

Miter Cuts

0-45°

Features

Dust extraction, Tilt function

Dimensions

31.5x31.9x21.7 inches (WxDxH)

Weight

101.41 lbs

M: QW-35-FL

Product Description

The Atika HT315: A Powerful Companion for Your Workshop

The Atika HT315 230V 3.0kW Electric Table Circular Saw Manual represents a significant upgrade for woodworkers seeking precision and power in a compact package. This robust machine is designed specifically for cutting solid wood and panel materials like chipboard, MDF, and plywood with square or rectangular cross-sections. Powered by a high-performance 3.0kW motor, it delivers the torque necessary to handle demanding cuts while maintaining smooth operation.

Safety is at the forefront of the design. The saw features a protective guard, a splitting wedge, and a reliable brake system that stops the blade within ten seconds of disengagement. Users are reminded that proper personal protective equipment, including ear protection and safety goggles, is essential during operation due to noise levels reaching up to 90.9 dB(A) under load. The machine also includes a dust extraction port compatible with standard vacuum systems to maintain a clean working environment.

Versatility is another key strength. The table dimensions of 800 x 550 mm provide ample space for large workpieces, while the continuous height and bevel adjustments allow for precise cuts up to 90 mm deep at angles up to 45 degrees. The inclusion of a push stick and adjustable fences ensures accurate rip and cross cuts, making it suitable for both professional joinery and serious DIY projects.

Maintenance is straightforward but requires diligence. Regular cleaning of resin buildup and oiling of moving parts without using grease will extend the lifespan of the unit. It is crucial to use only carbide-tipped blades within the specified diameter range of 300 to 315 mm, as HSS steel blades are strictly prohibited due to the risk of shattering.

Important Notes

  • Always ensure the machine is unplugged before changing blades or performing maintenance.
  • Do not operate the saw in wet conditions or near flammable liquids.
  • Children under 18 are strictly prohibited from operating this equipment.
M: QW-35-FL

© Copyright 2026 Manual.ly