Manual.ly Logo

Atika BF 31-4T Manual

0.0 · 0 Ratings

PDF manual · 216 Pages

English

M: QW-35-FL
page

/ 216

Loading...
f235a5ff041eb99b6e9e8eb12c89b2b29669 page f
15
Schrauben Sie die Öleinfüllschraube mit dem Messstab
fest.
Entsorgen Sie das Altöl umweltgerecht. Wir empfeh-
len, das Altöl in einem dicht verschlossenen Behälter
zu Ihrer örtlichen Servicestelle oder Tankstelle zu
bringen. Altöl nicht in den Hausmüll werfen, nicht
im Erdreich entsorgen oder in einen Abfluss schütten.
Der Betrieb des Motors mit zu niedrigem Ölstand kann
den Motor beschädigen.
Schalldämpfer / Austrittsöffnung
Kontrollieren Sie regelmäßig den Schalldämpfer (18).
Reinigen Sie regelmäßig die Austrittsöffnung.
Säubern Sie den Schalldämpfer nicht, wenn der
Motor heiß ist. Verbrennungsgefahr!
Leerlaufdrehzahl überprüfen bzw. einstellen
Der Vergaser ist ab Werk auf die richtige Leerlaufdrehzahl ein-
gestellt, so dass dem Motor das richtige Kraftstoff-Luft-Gemisch
zugeführt wird.
Die Leerlaufdrehzahl ist richtig eingestellt, wenn der Motor
gleichmäßig läuft und das Schneidwerkzeug still steht.
Überprüfen Sie die Leerlaufdrehzahl nur mit
− warmgelaufenem Motor;
− sauberem Luftfilter.
In folgenden Fällen muss der Vergaser (Leerlaufdrehzahl) korri-
giert werden:
− Schneidwerkzeug dreht sich im Leerlauf
− Drehzahl zu hoch
− unregelmäßiger Lauf oder mangelnde Beschleunigung
(Leerlaufdrehzahl zu niedrig)
− Anpassung an Wetterverhältnisse, Temperaturen
Eine falsche Vergasereinstellung führt zu schweren
Motorschäden! Arbeiten Sie auf keinen Fall mit dem
Gerät weiter.
Wenden Sie sich an den Kundendienst und lassen
Sie eine Vergasereinstellung durchführen.
Reinigung
Reinigen Sie das Gerät nach jedem Gebrauch sorgfältig,
damit die einwandfreie Funktion erhalten bleibt.
• Reinigen Sie regelmäßig alle beweglichen Teile.
• Reinigen Sie das Gehäuse mit einer weichen Bürste oder
einem trockenen Lappen.
• Das Gerät nicht mit fließendem Wasser oder Hoch-
druckreinigern reinigen.
• Verwenden Sie für die Kunststoffteile keine Lösungsmittel
(Benzin, Alkohol, usw.), da diese die Kunststoffteile beschä-
digen können.
• Halten Sie die Handgriffe frei von Öl und Fett.
Wasser, Lösungsmittel und Poliermittel dürfen nicht
verwendet werden.
• Achten Sie darauf, dass die Lüftungsschlitze für die Mo-
torkühlung frei sind (Gefahr der Überhitzung).
Transport
Vor jedem Transport
− Gerät ausschalten
− Stillstand des Schneidwerkzeugs abwarten
Tragen Sie das Gerät ausbalanciert am Schaft oder hän-
gend am Tragegurt.
Um Verletzungen oder Beschädigungen zu ver-
meiden, sichern Sie das Schneidmesser (7) und das Fa-
denmesser (10) gegen Berühren mit dem jeweiligen Trans-
portschutz (7a und 10a).
Transportieren Sie das Gerät im KFZ nur im Kofferraum
oder einer separaten Transportfläche. Beim Verladen das
Gerät nicht werfen. Sichern Sie dabei das Gerät gegen Um-
kippen, Beschädigungen und Auslaufen von Kraftstoff.
Überprüfen Sie das Gerät auf Beschädigungen, wenn es
beim Transport harten Stößen ausgesetzt wurde.
Lagerung
Bewahren Sie unbenutzte Geräte an einem trockenen, ver-
schlossenen Ort außerhalb der Reichweite von Kindern auf.
Lagern Sie das Gerät dort, wo Benzindämpfe nicht mit offe-
nem Feuer oder Funken in Kontakt kommen können (z. B.
nicht neben einen Herd, Ofen oder Warmwasserboiler mit
Dauerflamme).
Legen Sie zur Lagerung das Gerät nicht auf der Schutzhau-
be ab, am besten bewahren Sie es hängend auf. Um Platz
zu sparen können Sie die Handgriffe einschwenken.
Sichern Sie das Schneidmesser (7) mit dem Transport-
schutz (7a).
Beachten Sie folgendes, um die Lebensdauer des Gerätes
zu verlängern und ein leichtgängiges Bedienen zu gewährleis-
ten:
Normale Lagerung
Lagerung des Gerätes während einer Betriebspause (Betriebs-
pause nicht länger als 6 Wochen).
1. Führen Sie eine gründliche Reinigung und Wartung durch.
2. Überprüfen Sie das Gerät auf einwandfreien Zustand, damit
eine zuverlässige Nutzung des Gerätes gewährleistet ist.
3. Entleeren Sie den Kraftstofftank vollständig.
Entleeren Sie den Tank nur im Freien oder in gut belüf-
teten Räumen.
Entsorgen Sie Restkraftstoff vorschriftsmäßig (umwelt-
freundlich).
4. Fahren Sie den Vergaser leer.
Starten Sie hierfür den Motor und lassen ihn im Leerlauf lau-
fen bis er stoppt. Im Vergaser ist jetzt kein Kraftstoff mehr.
Kraftstoffreste im Vergaser können Startprobleme o-
der Schäden verursachen.
5. Lassen Sie den Motor abkühlen.
6. Behandeln Sie alle beweglichen Teile mit einem umwelt-
freundlichen Öl.
Verwenden Sie kein Fett.

Chat with your Atika BF 31-4T manual using AI

Get instant AI answers from your Atika BF 31-4T manual

Ask anything about the Atika BF 31-4T. Answers come from this manual, with the pages they are based on.

BF 31-4T Maintenance Schedule

Before each use
Check machine for defects and loose fasteners

Inspect for loose bolts, worn or damaged parts, bent cutting tools, and fuel leaks. Ensure all safety guards are intact.

Show in the manual (page 16)
After each use
Clean the device thoroughly

Remove dirt and grass residues from the housing and ventilation slots using a soft brush or dry cloth. Do not use high-pressure water.

Show in the manual (page 15)
Every 8 operating hours
Clean the air filter

Wash the air filter in lukewarm soapy water to prevent starting problems and power loss. Allow it to dry completely before reinserting.

Show in the manual (page 14)
Every 25 operating hours
Replace the spark plug

Change the spark plug every 100 hours or once a year, whichever comes first. Also replace if the insulator is damaged or electrodes are eroded.

Show in the manual (page 31)
Every 100 operating hours
Change the engine oil

Drain warm oil by tilting the engine over a container. Refill with recommended SAE 10W-30 oil (0.08 l capacity).

Show in the manual (page 14)
Regularly
Check and clean the silencer

Inspect the muffler regularly and clean the exhaust outlet to maintain performance. Do not clean while the engine is hot.

Show in the manual (page 15)
As needed
Sharpen or replace the thread knife

If the trimmer line is not cutting properly, unscrew the thread knife on the guard and sharpen it with a flat file or replace if damaged.

Show in the manual (page 13)
As needed
Check and adjust idle speed

Verify that the cutting tool does not rotate when idling. If it does, have the carburetor adjusted by an authorized service center.

Show in the manual (page 15)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend BF 31-4T?

Yes No

Frequently Asked Questions

A

The machine requires clean, fresh, unleaded gasoline with a minimum octane number of 91 ROZ. Do not use diesel, leaded petrol, or old fuel mixtures as these can cause severe engine damage.

Is this answer helpful?

A

No, the device is intended for grass and undergrowth up to 13mm diameter in private areas. It should not be used for cutting hedges, bushes, or flowers as this poses a risk of injury and voids the warranty.

Is this answer helpful?

A

Press the primer pump until fuel appears, set the choke lever to cold start, pull the starter rope firmly until the engine fires, then move the choke to the warm position once it ignites.

Is this answer helpful?

A

Yes, the thread spool can be replaced manually. You must lock the drive shaft with a screwdriver, unscrew the nut counter-clockwise, and insert the new roll ensuring the thread is clamped correctly.

Is this answer helpful?

A

You must wear a certified hard hat, eye protection, ear protection, cut-resistant gloves, trousers, and safety boots with steel toes. Loose clothing and jewelry are strictly prohibited.

Is this answer helpful?

A

The spark plug should be inspected regularly and replaced every 100 hours of operation or once a year, whichever comes first. It should also be replaced if the electrode is heavily worn or dirty.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Versatile dual-functionality allows switching between grass trimming and brush cutting.
  • Ergonomic double shoulder strap reduces user fatigue during long sessions.
  • Powerful 4-stroke engine handles thick undergrowth up to 13mm diameter effectively.
  • Comprehensive safety features including kickback protection and hot surface warnings.
  • Easy access to maintenance points like air filters and spark plugs.
VS

Disadvantages

  • High noise level of 113 dB requires mandatory hearing protection.
  • Hand-arm vibration levels require strict adherence to break schedules.
  • Small fuel tank capacity necessitates frequent refueling for large areas.
  • Requires manual assembly and setup before the first operation.
  • Not suitable for professional or commercial landscaping use.
M: QW-35-FL

Product Specification

Type

String trimmer

Power

700W, 0.95HP, 31cm³, 4-stroke

Cutting width

18.9in (line), 10in (blade)

Cutting system

Line (2-line technology), Blade (steel blade)

Line advance

Tap-advance

Line diameter

0.094in

Line length

8.2ft

Features

Auxiliary handle

Tank capacity

1.85gal

Noise level

113dB(A)

Weight

13.89lbs

Package contents

Shoulder strap, 2-piece accessory set

M: QW-35-FL

Product Description

Atika BF 31-4T Grass Trimmer Review

The Atika BF 31-4T is a versatile petrol-powered brush cutter and grass trimmer designed for private gardens and hobbyists. This robust machine combines the power of a 4-stroke OHV engine with a 31 cubic centimeter displacement to handle everything from light lawn edging to cutting dense undergrowth up to 13 millimeters in diameter. It features a dual-purpose design, allowing users to switch between a nylon line head for trimming grass and a metal blade for clearing brush, making it an essential tool for comprehensive garden maintenance.

Performance and Design

Equipped with a centrifugal clutch, this trimmer ensures that the cutting tool only rotates when the throttle is engaged, enhancing safety during startup. The unit delivers a maximum engine speed of 9300 RPM with the brush cutter attachment and 8000 RPM with the grass trimmer. Its ergonomic double shoulder strap distributes weight evenly, reducing fatigue during extended use. The protective hood shields the operator from flying debris while the integrated dirt catcher helps manage cut material.

Safety and Operation

Safety is paramount with the BF 31-4T. The manual emphasizes strict adherence to personal protective equipment, including helmets, eye protection, and hearing guards. The device includes a cold start mechanism and a primer pump for reliable ignition even in cool conditions. Operators must maintain a safe distance of at least 15 meters from bystanders and avoid operating in enclosed spaces due to carbon monoxide risks. The vibration levels are measured at approximately 7.06 m/s², requiring regular breaks to prevent hand-arm vibration syndrome.

Maintenance and Care

Regular maintenance extends the life of the Atika BF 31-4T. Users should routinely check the air filter, fuel filter, and spark plug. The engine oil capacity is small at just 0.08 liters, requiring careful monitoring via the dipstick. Cleaning should be done with a soft brush or dry cloth; high-pressure washers are strictly prohibited as they can damage internal components. Proper storage involves draining the fuel tank if the machine will not be used for more than six weeks to prevent carburetor issues.

Notes

  • Always read the full manual before first use.
  • Use only unleaded gasoline with an octane rating of at least 91.
  • Replace damaged parts immediately to ensure safety.
M: QW-35-FL

© Copyright 2026 Manual.ly