Manual.ly Logo

Atika BF 31-4T Manual

0.0 · 0 Ratings

PDF manual · 216 Pages

English

M: QW-35-FL
page

/ 216

Loading...
f235a5ff041eb99b6e9e8eb12c89b2b29669 page d
13
− Ein blockiertes Winkelgetriebe kann zu Kupplungsschäden
führen.
− Der Schneidfaden läuft nach dem Ausschalten des
Grastrimmers nach. Warten Sie deshalb ab, bis der Faden
stillsteht, bevor Sie das Gerät wieder einschalten. Wenn die
Fadenspule leer ist, ersetzen Sie diese durch eine Original
Fadenspule.
Fadennachführung
Der Schneidfaden nutzt sich während des Schneidvorganges
ab oder er kann reißen, so dass kein Gras mehr geschnitten
werden kann.
Die optimale Schneidfadenlänge kann während des
Trimmens durch ein kurzes Auftippen des Gerätes auf den
Boden eingestellt werden. Falls der Schneidfaden den ma-
ximalen Schneiddurchmesser überschreitet, wird er durch
das integrierte Messer (10) an dem Schmutzfänger (5a) der
Schutzhaube (5) gekürzt.
Ein beschädigter Schmutzfänger muss sofort ausge-
wechselt werden.
Verwenden Sie immer den Schmutzfänger (5a) mit
integriertem Fadenmesser beim Trimmen.
Wartung und Reinigung
Vor jeder Wartungs- und Reinigungsarbeit
− Motor ausschalten
− Stillstand des Schneidwerkzeugs abwarten
−
Zündkerzenstecker abziehen
−
Tragen Sie Schutzhandschuhe zur Vermeidung
von Verletzungen.
− Führen Sie Wartungsarbeiten nicht in der Nähe
von offenem Feuer durch. Brandgefahr!
Weitergehende Wartungs- und Reinigungsarbeiten, als die in
diesem Kapitel beschrieben, dürfen nur vom Kundendienst
durchgeführt werden.
Zum Warten und Reinigen entfernte Sicherheitseinrichtungen
müssen unbedingt wieder ordnungsgemäß angebracht und
überprüft werden.
Nur Originalteile verwenden. Andere Teile können zu unvorher-
sehbaren Schäden und Verletzungen führen.
Wartung
Das Schneidwerkzeug steht nach dem Ausschalten nicht sofort
still. Warten Sie, bevor Sie mit der Reparatur oder Wartung
beginnen, bis alle Teile zum Stillstand gekommen sind.
Damit eine lange und zuverlässige Nutzung des Gerätes ge-
währleistet ist, führen Sie die folgenden Wartungsarbeiten re-
gelmäßig aus.
Überprüfen Sie das Gerät auf offensichtliche Mängel wie
− lose Befestigungen
− verschlissene oder beschädigte Bauteile
− verbogenes, gebrochenes oder beschädigtes Schneidwerk-
zeug
− Tankverschluss und Kraftstoffleitungen auf Dichtigkeit
Notwendige Reparaturen oder Wartungsarbeiten sind vor
dem Einsatz des Gerätes durchzuführen.
Fadenspulenrolle wechseln
Demontieren Sie zum Auswechseln zuerst die Fadenspule
von der Antriebswelle.
Arretieren Sie hierzu die Antriebswelle (H) mit dem
Schraubendreher (39). Drehen Sie dann die Fadenspule (6)
im Uhrzeigersinn.
Drücken Sie die Arretierung am Spulenunterteil (I) der
Fadenspule. Drehen Sie den Spulendeckel (6a) im Uhrzei-
gersinn.
Entnehmen Sie die Fadenspulenrolle (6b) und die
Druckfeder (6c).
Entfernen Sie Schmutz und Grasreste.
Legen Sie die Druckfeder (6c) in das Spulenunterteil (I).
Setzen Sie die neue Fadenspulenrolle (6b) ein.
Fädeln Sie jeden Faden einzeln in eine der beiden Faden-
führungen im Spulenunterteil (I) ein.
Achten Sie unbedingt darauf, dass der einge-
klemmte Faden über der Fadenführung liegt.
Legen Sie den Spulendeckel (6a) auf das Spulenunter-
teil (I).
Drehen Sie die Fadenspule um.
Achten Sie darauf, dass die Arretierungen im Spulenunter-
teil über den Aussparungen im Spulendeckel liegen. Drü-
cken Sie das Unterteil kräftig nach unten. Drücken Sie
gleichzeitig die Arretierung im Spulenunterteil ein. Drehen
Sie das Spulenunterteil gegen den Uhrzeigersinn bis diese
Arretierung einrastet.
Falls das Aufwickeln des Fadens erforderlich
ist, gehen Sie folgendermaßen vor:
Knicken Sie den Faden in der Mitte und legen Sie ihn in
den Schlitz der Trennwand ein. Halten Sie die Fadenspulen-
rolle wie im Bild gezeigt. Ziehen Sie den Faden in Pfeilrich-
tung.
Wickeln Sie den Faden straff auf die Fadenspulenrolle,
indem Sie die Rolle im Uhrzeigersinn drehen.
Klemmen Sie beide Fäden in die Schlitze, damit sich
der Faden beim Einsetzen der Fadenspulenrolle nicht abwi-
ckeln kann.
Fadenmesser schärfen bzw. erneuern
Schrauben Sie das Fadenmesser (10) ab.
Spannen Sie das Fadenmesser in einen Schraubstock und
schärfen Sie es mit einer Flachfeile.
Achten Sie darauf, dass Sie den Winkel des Messers nicht
verändern und nur in eine Richtung feilen.
Feilen Sie vorsichtig.
Schrauben Sie das Fadenmesser wie abgebildet wieder an.
Die Schrauben nicht zu stark anziehen.
Verwenden Sie kein ungeschärftes bzw. beschädig-
tes Fadenmesser. Ein beschädigtes Fadenmesser
muss durch ein neues ersetzt werden.

Chat with your Atika BF 31-4T manual using AI

Get instant AI answers from your Atika BF 31-4T manual

Ask anything about the Atika BF 31-4T. Answers come from this manual, with the pages they are based on.

BF 31-4T Maintenance Schedule

Before each use
Check machine for defects and loose fasteners

Inspect for loose bolts, worn or damaged parts, bent cutting tools, and fuel leaks. Ensure all safety guards are intact.

Show in the manual (page 16)
After each use
Clean the device thoroughly

Remove dirt and grass residues from the housing and ventilation slots using a soft brush or dry cloth. Do not use high-pressure water.

Show in the manual (page 15)
Every 8 operating hours
Clean the air filter

Wash the air filter in lukewarm soapy water to prevent starting problems and power loss. Allow it to dry completely before reinserting.

Show in the manual (page 14)
Every 25 operating hours
Replace the spark plug

Change the spark plug every 100 hours or once a year, whichever comes first. Also replace if the insulator is damaged or electrodes are eroded.

Show in the manual (page 31)
Every 100 operating hours
Change the engine oil

Drain warm oil by tilting the engine over a container. Refill with recommended SAE 10W-30 oil (0.08 l capacity).

Show in the manual (page 14)
Regularly
Check and clean the silencer

Inspect the muffler regularly and clean the exhaust outlet to maintain performance. Do not clean while the engine is hot.

Show in the manual (page 15)
As needed
Sharpen or replace the thread knife

If the trimmer line is not cutting properly, unscrew the thread knife on the guard and sharpen it with a flat file or replace if damaged.

Show in the manual (page 13)
As needed
Check and adjust idle speed

Verify that the cutting tool does not rotate when idling. If it does, have the carburetor adjusted by an authorized service center.

Show in the manual (page 15)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend BF 31-4T?

Yes No

Frequently Asked Questions

A

The machine requires clean, fresh, unleaded gasoline with a minimum octane number of 91 ROZ. Do not use diesel, leaded petrol, or old fuel mixtures as these can cause severe engine damage.

Is this answer helpful?

A

No, the device is intended for grass and undergrowth up to 13mm diameter in private areas. It should not be used for cutting hedges, bushes, or flowers as this poses a risk of injury and voids the warranty.

Is this answer helpful?

A

Press the primer pump until fuel appears, set the choke lever to cold start, pull the starter rope firmly until the engine fires, then move the choke to the warm position once it ignites.

Is this answer helpful?

A

Yes, the thread spool can be replaced manually. You must lock the drive shaft with a screwdriver, unscrew the nut counter-clockwise, and insert the new roll ensuring the thread is clamped correctly.

Is this answer helpful?

A

You must wear a certified hard hat, eye protection, ear protection, cut-resistant gloves, trousers, and safety boots with steel toes. Loose clothing and jewelry are strictly prohibited.

Is this answer helpful?

A

The spark plug should be inspected regularly and replaced every 100 hours of operation or once a year, whichever comes first. It should also be replaced if the electrode is heavily worn or dirty.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Versatile dual-functionality allows switching between grass trimming and brush cutting.
  • Ergonomic double shoulder strap reduces user fatigue during long sessions.
  • Powerful 4-stroke engine handles thick undergrowth up to 13mm diameter effectively.
  • Comprehensive safety features including kickback protection and hot surface warnings.
  • Easy access to maintenance points like air filters and spark plugs.
VS

Disadvantages

  • High noise level of 113 dB requires mandatory hearing protection.
  • Hand-arm vibration levels require strict adherence to break schedules.
  • Small fuel tank capacity necessitates frequent refueling for large areas.
  • Requires manual assembly and setup before the first operation.
  • Not suitable for professional or commercial landscaping use.
M: QW-35-FL

Product Specification

Type

String trimmer

Power

700W, 0.95HP, 31cm³, 4-stroke

Cutting width

18.9in (line), 10in (blade)

Cutting system

Line (2-line technology), Blade (steel blade)

Line advance

Tap-advance

Line diameter

0.094in

Line length

8.2ft

Features

Auxiliary handle

Tank capacity

1.85gal

Noise level

113dB(A)

Weight

13.89lbs

Package contents

Shoulder strap, 2-piece accessory set

M: QW-35-FL

Product Description

Atika BF 31-4T Grass Trimmer Review

The Atika BF 31-4T is a versatile petrol-powered brush cutter and grass trimmer designed for private gardens and hobbyists. This robust machine combines the power of a 4-stroke OHV engine with a 31 cubic centimeter displacement to handle everything from light lawn edging to cutting dense undergrowth up to 13 millimeters in diameter. It features a dual-purpose design, allowing users to switch between a nylon line head for trimming grass and a metal blade for clearing brush, making it an essential tool for comprehensive garden maintenance.

Performance and Design

Equipped with a centrifugal clutch, this trimmer ensures that the cutting tool only rotates when the throttle is engaged, enhancing safety during startup. The unit delivers a maximum engine speed of 9300 RPM with the brush cutter attachment and 8000 RPM with the grass trimmer. Its ergonomic double shoulder strap distributes weight evenly, reducing fatigue during extended use. The protective hood shields the operator from flying debris while the integrated dirt catcher helps manage cut material.

Safety and Operation

Safety is paramount with the BF 31-4T. The manual emphasizes strict adherence to personal protective equipment, including helmets, eye protection, and hearing guards. The device includes a cold start mechanism and a primer pump for reliable ignition even in cool conditions. Operators must maintain a safe distance of at least 15 meters from bystanders and avoid operating in enclosed spaces due to carbon monoxide risks. The vibration levels are measured at approximately 7.06 m/s², requiring regular breaks to prevent hand-arm vibration syndrome.

Maintenance and Care

Regular maintenance extends the life of the Atika BF 31-4T. Users should routinely check the air filter, fuel filter, and spark plug. The engine oil capacity is small at just 0.08 liters, requiring careful monitoring via the dipstick. Cleaning should be done with a soft brush or dry cloth; high-pressure washers are strictly prohibited as they can damage internal components. Proper storage involves draining the fuel tank if the machine will not be used for more than six weeks to prevent carburetor issues.

Notes

  • Always read the full manual before first use.
  • Use only unleaded gasoline with an octane rating of at least 91.
  • Replace damaged parts immediately to ensure safety.
M: QW-35-FL

© Copyright 2026 Manual.ly