Manual.ly Logo

ARKA myAQUA 1900 Manual

0.0 · 0 Ratings

PDF manual · 16 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 16

Loading...
8865e82a3b88f42820bc04fd8cb59a424596 page 8
ARKA myAQUA® 1900 Reverse Osmosis System
Thank you for purchasing our ARKA myAQUA® 1900. ARKA myAQUA® 1900 quickly and eectively lters up to 99% of salts, bacteria and
pollutants (such as nitrate, phosphate and heavy metals) from tap water, making it safe for use in any saltwater or freshwater aquarium.
PLEASE NOTE: Please read the instructions carefully and keep them in a safe place.
Product description
ARKA myAQUA® 1900 achieves a water yield of up to 1:1 and contains only natural filter materials without chemical additives. Thanks to the
accessories included in the shipment it can be connected to standard household waterpipes.
First, the tap water passes through a ne lter (1 micro pore in width) and a carbon lter and is pre-ltered. It then passes through an
ultrane special membrane (0.0001 micron), which only allows through the smallest water molecules and thus lters out up to 99% of the
pollutants. Finally, the water passes through a second carbon lter or, alternatively, the resin lter.
PP Fine lter: Filters dirt particles and impurities such as rust and sand out of the water.
C1 Carbon lter: Filters odours, discolourations, chlorine, herbicides, pesticides and drug residues from the water.
C2 Carbon lter: Filters chlorine, herbicides, pesticides and drug residues from the water.
RO Membrane: Filters pollutants, salts, heavy metals, pesticides and bacteria from the water.
Technical data:
Osmosis water : Residual water Yield approx. 1:1–1,5
Flow rate max. 1,32 l/min
Operating pressure 1 – 4 bar
Usable water temperature 5 – 38°C
Salt retention capacity up to 99 %
Membrane Non-woven fabric reinforced by polyester
Dimensions approx. 434 mm x 163 mm x 418 mm
Power 70 W
Standby Power 1-2 W
Voltage 24 V
IMPORTANT: Quality, temperature and pressure of the tap water can inuence the actual water yield and the quality of the osmosis
water. Please note that water with a TDS value below 50 ppm is considered osmosis water.
Optionally available:
Resin lter:
Perfect as a supplement to remove even the nest residues of silicate, nitrate and many other dissolved organic and inorganic substan-
ces (TDS). The resin lter can easily be connected to the osmosis system instead of the C2 Carbon lter.
8
Fine lter Carbon lter
1
Flush Carbon lter
2
Membrane Reset
PP
Flush Reset
C1 C2
RO
To mount the hoses, rst remove the inserted transport
locks. To do this, press the movable rim of the hose con-
nection (Fig. 1) downwards and carefully pull out the
transport lock. Now insert the corresponding hose into
the connection and secure it with the supplied blue safety
clips (Fig. 3 & 4).
PP C1 C2 RO
Tap
water
supply
Osmosis
water
supply
Elec-
tricity
supply
Waste
water
WEEE-Reg.-Nr. DE 40563632

Chat with your ARKA myAQUA 1900 manual using AI

Get instant AI answers from your ARKA myAQUA 1900 manual

Ask anything about the ARKA myAQUA 1900. Answers come from this manual, with the pages they are based on.

myAQUA 1900 Maintenance Schedule

Remind me when maintenance is due
Every 6-12 months
Replace filters

Change the fine filter and carbon filters every 6 to 12 months from first use. Actual duration depends on water quality and usage.

Every 12-24 months
Replace membrane

Replace the RO membrane every 12 to 24 months from first use. Actual duration depends on water quality and usage.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend myAQUA 1900?

Yes No

Frequently Asked Questions

A

The system filters up to 99 percent of salts, bacteria, and pollutants, ensuring TDS values remain below 50 ppm for clean water.

Is this answer helpful?

A

Filters generally need replacement every six to twelve months, while the membrane should be changed every twelve to twenty-four months.

Is this answer helpful?

A

No, the resin filter is an optional accessory that can be connected instead of the C2 carbon filter after the rinse cycle.

Is this answer helpful?

A

An automatic protection function interrupts production after twelve hours to preserve the pump and membrane longevity during extended use.

Is this answer helpful?

A

Yes, with the included accessories, it can be connected to standard household water pipes with a pressure between 1 and 4 Bar.

Is this answer helpful?

A

Yes, the device uses smart reminder lights and audible signals to indicate when filters or membranes require replacement or resetting.

Is this answer helpful?

A

The maximum flow rate is 1.32 liters per minute with a water yield ratio of approximately 1:1 to 1:5 depending on source conditions.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Filters up to 99 percent of salts, bacteria, and harmful pollutants for safe aquarium use.
  • Natural filter materials without chemical additives ensure pure water quality.
  • Built-in protection function stops production after twelve hours to protect the pump.
  • Smart reminder lights and reset function simplify filter maintenance scheduling.
  • Compact dimensions and easy connection to standard household plumbing lines.
VS

Disadvantages

  • Resin filter must be installed only after the initial rinse cycle completes.
  • Performance depends on water pressure staying strictly between 1 and 4 Bar.
  • Filters require replacement every six to twelve months for optimal efficiency.
  • System automatically shuts down, requiring a power reset to resume production.
  • Membrane lifespan is limited and must be replaced every twelve to twenty-four months.
M: qwen/qwen3.5-flash-20260224

Product Specification

Category

Reverse Osmosis, Water Treatment

Type

Reverse Osmosis Unit (Pressure Booster Pump with Automatic Shutoff, Fine Filter, 2x Activated Carbon Filters, Filter Membrane, Conductivity Meter)

Specifications

501.93 gal/d, Ratio to Waste Water 1:1

Suitability

Fresh Water, Seawater, Aquarium, Terrarium

Power Consumption

Max. 70 W

Dimensions

17.09x16.46x6.42in (WxHxD)

M: qwen/qwen3.5-flash-20260224

Product Description

Comprehensive Guide to Clean Aquarium Water

Introducing the ARKA MyAqua 1900 Reverse Osmosis System

Are you searching for the ultimate purification method for your aquarium? The ARKA MyAqua 1900 Reverse Osmosis System with 24V Boost Pump, 1900l Manual delivers exceptional clarity and safety for your aquatic pets. This advanced unit filters up to 99 percent of salts, bacteria, and harmful pollutants such as nitrate, phosphate, and heavy metals from standard tap water. It transforms ordinary source water into a pristine environment suitable for sensitive saltwater and freshwater species.

The filtration process involves multiple stages for maximum effectiveness. Tap water first enters a PP fine filter with a one-micron pore size to trap dirt and rust particles. It then moves through a C1 carbon filter which eliminates odors, chlorination, and pesticide residues. The critical RO membrane follows, blocking 0.0001 microns to remove dissolved solids effectively. A second carbon filter or optional resin filter completes the process, ensuring the TDS value stays below 50 ppm. This setup guarantees chemical-free filtration using only natural materials.

Technical Specifications and Setup

Operating with a 24 V power supply, this system balances performance with energy efficiency. It boasts a maximum flow rate of 1.32 liters per minute and maintains a water yield ratio of approximately 1:1 to 1:5. Dimensions are compact at 434 mm x 163 mm x 418 mm. It consumes 70 W during production and as low as 2 W in standby. Water temperature must be between 5 and 38 degrees Celsius. Pressure requirements are strict, ranging from 1 to 4 Bar for safe operation. Installation is easy, connecting directly to standard household plumbing lines with the provided hoses and adapters. The system includes a built-in protection function that automatically shuts down production after twelve hours of continuous running. This feature preserves the pump and membrane longevity during extended use.

Regular maintenance is key to optimal performance. The device features smart reminder lights and audible signals when filters or membranes require replacement. Standard intervals suggest changing filters every six to twelve months and the membrane every twelve to twenty-four months. A flush program takes sixty seconds to clear sediment, and the reset function keeps track of component usage. Ensure hoses are secured with blue clips. Check for leaks regularly to maintain efficiency. The system will warn you if maintenance is needed. Proper care extends the lifespan of all internal parts. Always disconnect power before unplugging connections to avoid pump damage from air ingestion. Keep the unit above zero degrees Celsius to prevent freezing. Follow the detailed instructions provided to maintain warranty validity and ensure safe operation for the best aquascaping results.

Note: Resin filters should be installed only after the initial rinse cycle completes.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly