Manual.ly Logo

Alphacool Eisblock Aurora GPX-N RTX 3070 Manual

0.0 · 0 Ratings

PDF manual · 4 Pages

English

M: QW-35-FL
page

/ 4

Loading...
840fcccc3675f8374f5300dda1eb803c7d5f page 1
Read the safety instructions before starting the installation.
Lesen Sie die Sicherheitshinweise, bevor Sie mit der Installation beginnen.
Lisez les instructions de sécurité avant de commencer l‘installation.
EN
DE
FR
ACCESSORIES
ZUBEHÖR
1x
8x84x1mm pad
1x
15x28x1mm pad
2x
15x40x1mm
pads
1x
30x30x2mm pad
1x
8x84x3mm pad
1x
15x28x3mm pad
2x
15x40x3mm
pads
5x
M2x5 screws
5x
M2x5 washers
6x
M2x11 screws
2x
Screw plugs
1x
Plug tool
1x
Thermal grease
1x
Digital–RGB
adapter
Put the hardware on an antistatic mat.
Begin dismantling the original cooler.
Depending on the structure of the cooler, remove
the screws at the back of the card and carefully
unhook the fan connector first. If the original
cooler uses thermal glue, extreme care should be
taken as you can easily damage parts. Pick up all
the items carefully. Next, clean the hardware of
thermal paste or pad residues with a solvent (e.g.
isopropanol alcohol).
Before starting the cooler assembly, compare
your card with the picture above. The cooler is
constructed specifically for this layout.
Occasionally, graphics card manufacturers may
revise the design of their card slightly, causing the
cooler not to fit on later models. During assembly,
please make sure taller parts have enough space
around them and that the cooler does not
damage your graphics card.
Alphacool International GmbH is not liable for
assembly errors occurring due to negligence,
such as selecting an incompatible cooler.
Legen Sie die Hardware auf eine
antistatische Unterlage. Beginnen Sie
mit der Demontage des Original-Kühlers. Je nach
Aufbau des Kühlers sind zuerst die Schrauben
des Lüfters zu entfernen und die Blenden zu
lösen. Bei aufgeklebten Kühlern ist äußerste
Sorgfalt geboten. Es können leicht Bauteile
abgerissen werden. Heben Sie alle Einzelteile
sorgfältig auf. Reinigen Sie anschließend die
Hardware von Resten der Wärmeleitpaste oder
Pads mit einem Lösemittel (z.B. Isopropanol-
Alkohol).
Bevor Sie mit der Montage des Kühlers beginnen,
vergleichen Sie Ihre Platine mit dem vorliegenden
Foto. Der Kühler wurde speziell für dieses Layout
konstruiert. Es kommt vor, dass
Grafikkartenhersteller über Revisionen den
Aufbau leicht abändern und damit der Kühler auf
spätere Modelle nicht mehr passt. Achten Sie
auch bei der Montage darauf, dass hohe Bauteile
frei liegen und der Kühler die Grafikkarte nicht
beschädigt.
Alphacool International GmbH haftet nicht bei
fahrlässigen Montagefehlern, wie die Wahl eines
inkompatiblen Kühlers.
Posez le matériel sur un tapis
antistatique. Commencez par le
démontage du refroidisseur d’origine. Selon la
configuration du radiateur les vis du ventilateur et
les caches doivent être enlevés d’abord. S’il s’agit
d’un refroidisseur collé il faut travailler très
doucement. Sinon des composants peuvent
s’arracher. Conservez tous les pièces
soigneusement. Ensuite, nettoyer le matériel de
résidus de la pâte thermique ou de pads avec un
solvant (alcool isopropanol par ex.).
Avant de commencer l’installation merci de
vérifier que votre carte ressemble bien a celle sur
l’image. Le refroidisseur a été conçu
spécialement pour cette disposition des
composants. Il est possible que le fabricant
change des détails dans la disposition de ses
composants lors d’une révision et que le bloc de
refroidissement ne soit plus compatible. Veillez
lors de l’installation au fait que les composants
hauts ne touchent pas le bloc de refroidissement
et que le bloc n’endommage pas la carte
graphique.
Alphacool International GmbH n’est pas
responsable ni des erreurs d’installation ni du
choix d’un refroidisseur incompatible.
EN
N
DE
FR
DE
FR
EN
1
2
3
4
5
6
7
3070
1.
Alphacool Eisblock Aurora Acryl GPX-N RTX
3070 Gaming X Trio incl. Backplate

Chat with your Alphacool Eisblock Aurora GPX-N RTX 3070 manual using AI

Get instant AI answers from your Alphacool Eisblock Aurora GPX-N RTX 3070 manual

Ask anything about the Alphacool Eisblock Aurora GPX-N RTX 3070. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Eisblock Aurora GPX-N RTX 3070?

Yes No

Frequently Asked Questions

A

Not necessarily. Manufacturers sometimes revise PCB designs. You must verify compatibility using the official configurator tool or compare PCB numbers before purchasing.

Is this answer helpful?

A

You need a plastic strip for paste application, isopropanol for cleaning, and the included screwdriver tool for sealing unused inlets. Standard screwdrivers are also required for mounting.

Is this answer helpful?

A

No, the RGB controller is not included. The kit provides a digital-RGB adapter that connects to external controllers like the Alphacool Aurora Eiscontrol.

Is this answer helpful?

A

The thermal paste layer should be less than one millimeter thick to prevent contamination of surrounding components while ensuring efficient heat transfer.

Is this answer helpful?

A

No, you must remove the original backplate to install the new copper block. A new backplate is included in the kit to be reattached after the block is mounted.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Superior thermal performance compared to stock coolers
  • Includes digital-RGB adapter for customizable lighting effects
  • Full coverage design protects GPU and VRAM effectively
  • Backplate included for added structural rigidity
VS

Disadvantages

  • Requires manual installation which may void warranty
  • Compatibility issues possible with revised PCB layouts
  • Complex assembly process requiring specific tools
  • No controller included for RGB lighting management
M: QW-35-FL

Product Specification

Type

GPU

Connectors

G1/4"

Lighting

LED (RGB)

Features

Voltage converter with integrated cooling (GPU), including backplate

M: QW-35-FL

Product Description

Alphacool Eisblock Aurora GPX-N RTX 3070: Ultimate Cooling Upgrade

The Alphacool Eisblock Aurora GPX-N RTX 3070 is a premium water cooling solution designed to transform the thermal performance of your graphics card. This full-cover block integrates an acrylic top with RGB lighting, allowing for seamless integration into custom loop builds while maintaining the aesthetic appeal of the original hardware. The unit features a copper base that ensures efficient heat transfer from the GPU and memory modules.

Installation requires careful preparation. Users must remove the original cooler and clean all thermal paste residues using isopropanol alcohol. It is crucial to check compatibility before assembly, as PCB revisions by manufacturers can affect fitment. The kit includes necessary screws, washers, and a digital-RGB adapter for connecting to controllers like the Alphacool Aurora Eiscontrol. Proper application of thermal paste on the GPU and placement of thermal pads on the VRAM and power stages are essential steps for optimal operation.

Key Features and Benefits

This cooler supports taller components and includes a backplate for structural support. The design minimizes the risk of damaging surrounding components if installed correctly. Users should ensure all inlets not used for tubing are sealed with provided screw plugs to prevent leaks. The system offers superior cooling capabilities compared to stock air solutions, making it ideal for overclocking enthusiasts who demand silence and low temperatures.

Important Notes

  • Always use an antistatic mat during installation.
  • Apply thermal paste in a layer thinner than one millimeter.
  • Verify PCB layout compatibility via the manufacturer configurator.
  • Tighten screws crosswise to ensure even pressure distribution.
M: QW-35-FL

© Copyright 2026 Manual.ly