Manual.ly Logo

Alphacool Eisball Digital RGB Manual

3.7 · 3 Ratings

PDF manual · 49 Pages

English

M: QW-35-FL
page

/ 49

Loading...
c3973c49c0ddd1c71fdf2cf60ec3989dd09e page 10
Eisball Alphacool International GmbH
15
ENGLISH
SAFETY INSTRUCTIONS
READ THE SAFETY INSTRUCTIONS BEFORE STARTING THE INSTALLATION.
• Not suitable for children under 6 years. (contains small parts which could be swallowed).
• Do not run any cooling components without ensuring that cooling liquid is flowing through the cooling system. Coolers operated without coolant
can become very hot. Caution: Burn Hazard!
• Coolers that have no coolant flowing through them can destroy the computer hardware. When switching on the hardware, always make sure that
the pump is working.
• Please note when tightening the connectors or fittings, no tools such as screwdrivers, pliers, or wrenches should be used. All plastic products or
metal threaded connections, which are linked with plastic parts, are easily over-loaded with tools. Cracking or other damages incurred in this way,
as well as damage from leaking coolant, are not covered under the warranty!
• Use only connectors with a sealing o-ring. When using a sealing ring a firm tightening with the hand is enough. Your instruction manual will
clearly refer to the use of tools in exceptional cases.
• If you have not done so yet, please check your hardware and cooling system (tightness, pump function and fans). This will minimize time spent
searching for possible problems. ALPHACOOL INTERNATIONAL GMBH accepts no liability on the warranty of the manufacturer of the electronic
components. The assembly of the cooling system takes place at your own risk.
• The screws should not be tightened too firmly. If you tighten the screws excessively, the knurled nuts can loosen and the cooler´s uniform
pressure is no longer guaranteed.
• Fasten the connections of your choice to the cooler. Do not use tools such as wrenches for fastening the connections. Connectors with 8mm long
threads may stop the flow.
• We recommend a tightness test before assembling/installing the cooler. The water pressure in the water cooling loop can be at a maximum of
0.8 bar. DO NOT use tools on the connectors.
• Ensure that the cooler is touching all components to be cooled through thermal grease and thermal pads.
• Only use distilled water or ALPHACOOL CAPE KELVIN CATCHER in your cooling circuit. Damage caused by unsuitable coolant is not covered
by the warranty!
Specified normal operation
All ALPHACOOL INTERNATIONAL GMBH cooling components are constructed and licensed for ALPHACOOL INTERNATIONAL GMBH
computer construction parts. The warranty expires in case of misuse.
Warranty
1. Data, designs, illustrations, technical data, weight, measurement and specifications, contained in folders, catalogues, circulars, announcements
or price lists, have a purely informative character. We do not undertake warranty for the correctness of these data. As to the kind and the range of
delivery, the data contained in the order and confirmation of order alone are decisive.
2. If there is a lack of warrantor, you are entitled, on the basis of the legal regulations to require subsequent delivery, to withdraw from the contract
or reduce the purchase price. If you are a consumer, the limitation period of warranty claims for the supplied commodity amounts to two years
starting from receipt of goods (§ 13 BGB). If you are an entrepreneur, in accordance with legal conditions the limitation period amounts to only one
year (§ 14 BGB).
3. The warranty claim is valid only in combination with the original invoice, the sales slip or an ALPHACOOL confirmation on warranty claim.
4. It is ALPHACOOL INTERNATIONAL GMBHs own discretionary authority to replace or repair the defective product or defective component. The
replaced product or component changes into property of ALPHACOOL INTERNATIONAL GMBH.
5. All warranty claims are accomplished by ALPHACOOL INTERNATIONAL GMBH or its authorized dealers. If the repair is carried out by a non-
authorized or assigned person, ALPHACOOL INTERNATIONAL GMBH does not take over either costs or liability, unless the repair has been
previously agreed upon with ALPHACOOL INTERNATIONAL GMBH.
6. All costs resulting from refitting of the products are not taken over by ALPHACOOL INTERNATIONAL GMBH.
7. ALPHACOOL INTERNATIONAL GMBHs warranty excludes the following points:
7.1. Regular controls maintenance and repair or the replacement of parts subject to regular wear and tear.
7.2. Improper manipulation or defects caused by incorrect installation.
7.3. Damages caused by storm, water, fire, overvoltage, acts of God, war, incorrect connection to the net, insufficient or incorrect
ventilation or other reasons over which ALPHACOOL INTERNATIONAL GMBH has no influence.
7.4. Damages resulting from transportation or improper packaging.
8. Consumer´s rights are valid in the respective country; demands made to the salesman, as explained and laid down in the sales contract, will not
be covered by this warranty. ALPHACOOL INTERNATIONAL GMBH, its Branch Office and Distributors, are not responsible for direct or indirect
damage or losses, as far as the
compelling legal regulations do not oppose it.
9. ALPHACOOL INTERNATIONAL GMBH does not take over the warranty of the manufacturer of the electronic construction units and
components. The assembly of the cooler takes place at your own risk.
Contact an authorized waste management company in your
country. A waste removal with the municipal waste (unsorted
garbage) or similar mechanisms for the collection of local wastes
is not permissible!

Chat with your Alphacool Eisball Digital RGB manual using AI

Get instant AI answers from your Alphacool Eisball Digital RGB manual

Ask anything about the Alphacool Eisball Digital RGB. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Eisball Digital RGB?

Yes No
0
User Pic

Harvey Saunders

7 months ago

Do you recommend monitoring temperatures closely? Some reviews mention pump failure leading to shutdowns. Is the power connector stable?

0
User Pic

Manual.ly

7 months ago

Thank you for the inquiry. While many users appreciate the design and silence, isolated reports exist of pump failure causing overheating. We strongly advise frequent temperature checks during initial setup. Regarding the power connector, ensure pins are fully seated to avoid disconnection. Use cable ties for strain relief if needed. Keep in mind the large dimensions require adequate case clearance for airflow around the sphere.

M: QW-35-FL
M: QW-35-FL

Frequently Asked Questions

A

The Alphacool Iceball Digital RGB holds approximately 700 ml of cooling fluid. This volume provides adequate buffer space for custom loops.

Is this answer helpful?

A

The tank is compatible with VPP655 and VPP755 pumps, though installed pump height must not exceed 50 mm for proper fitment.

Is this answer helpful?

A

No, tools such as wrenches should never be used on connectors. Plastic parts fracture easily under torque and void the warranty.

Is this answer helpful?

A

Only distilled water or approved Alphacool fluids like CKC should be used. Unsuitable liquids cause damage and invalidate warranty claims.

Is this answer helpful?

A

Yes, the water pressure in the cooling loop must not exceed 0.8 bar to ensure the integrity of seals and fittings.

Is this answer helpful?

A

Running the pump dry destroys hardware and creates burn hazards. Always verify flow before powering on the system.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Large 700 ml volume ensures stable thermal management for demanding workloads.
  • Compatible with VPP655 and VPP755 pumps for versatile configuration options.
  • Includes mini aRGB controller for synchronized lighting customization.
  • Multiple mounting methods including plate and fan bracket support.
  • Integrated vibration dampers significantly reduce operational noise levels.
VS

Disadvantages

  • Requires strict use of distilled water to avoid voiding warranty coverage.
  • Using tools on fittings can damage plastic parts and cause leaks.
  • Warranty does not cover external electronic component manufacturers.
  • Water level drops after first run requiring immediate refilling.
  • Maximum loop pressure restricted to 0.8 bar for safety reasons.
M: QW-35-FL

Product Specification

Type

Expansion tank

Material

Brass, POM, PMMA

Capacity

23.67 fl oz

Connections

1/4 inch

Pump

8-13 V, 92.46 gph, 13.94 ft

Lighting

LED (RGB)

Dimensions

5.12 x 5.04 x 5.04 in

Color

Clear (transparent), White

M: QW-35-FL

Product Description

Enhancing PC Cooling Performance

The Alphacool Iceball Digital RGB represents a pinnacle of efficiency and aesthetics for custom water-cooled systems designed for serious gamers. This expansion tank unit delivers substantial cooling capacity with approximately 700 ml of total volume, ensuring stable temperatures during intense gaming workloads. Compatibility extends to the VPP655 and VPP755 pumps, allowing users to customize their setup with highly reliable pumping power. The digital RGB lighting enhances visual presentation, syncing with other components via an included mini aRGB controller and adapter for seamless customization. Proper integration begins by carefully placing the LED ring onto the reservoir from above before securing tubing connections tightly.

Assembly and Installation

Assembly involves multiple stages requiring precision to ensure long-term system longevity. The package includes a mounting plate or fan bracket option depending on internal chassis preferences. Four M3x5 screws and four M4x5 screws facilitate secure attachment to computer cases alongside specialized Velcro mats for vibration control effectiveness. Additionally, four rubber vibration dampers reduce mechanical noise transmission significantly during operation cycles. A sealing plug closes unused threaded inputs to prevent leaks effectively during extended usage. Tubing connects to ports clearly labeled IN and OUT respectively, while the third input port stays sealed permanently with the provided screw tool kit.

Safety and Compliance

Safety remains paramount throughout the entire usage duration period. Operators must never utilize wrenches or pliers on connector threads because plastic components fracture easily under excessive torque force. Excessive tightening voids coverage immediately and causes significant fluid damage liability issues later. Liquid flow verification is mandatory before powering hardware to avoid burn hazards or catastrophic component destruction risks. Maximum water pressure within the closed loop must remain under 0.8 bar to maintain structural integrity of rubber seals. Only distilled water or approved Alphacool fluids are permitted to preserve warranty standing correctly. Improper coolants cause permanent damage and inevitably lead to denied warranty claims.

Maintenance and Usage

Post-installation maintenance requires frequent attention initially to stabilize the loop. The water level often drops after running the pump for the first time due to initial air displacement. Users should refill through the top fillport funnel opening until reaching ten millimeters below the designated rim height mark. Regular monitoring ensures continued safe operation over many months of usage. Disposal follows strict environmental regulations using authorized waste companies rather than general municipal trash bins. Electronic component warranties from third parties are excluded by the manufacturer entirely during production. Responsibility lies with the installer for correct fitting procedures on all metal and plastic surfaces. Detailed step-by-step instructions accompany every component included in the box for easy setup. Each thread input accepts tubing securely when tightened by hand firmly. O-rings ensure watertight seals on all connection points without additional grease. Installation guides explain how to mount the component correctly. This solution provides excellent thermal performance for overclocked processors and graphics cards. It supports UV free coolant options for crystal clear visuals without damaging components over time. Users benefit from reduced acoustic footprint thanks to the advanced damping technology integrated internally.

M: QW-35-FL

© Copyright 2026 Manual.ly