Manual.ly Logo

ABB DLR/S 8.16.1M Manual

0.0 · 0 Ratings

PDF manual · 220 Pages

English

M: QW-35-FL
page

/ 220

Loading...
ba8e383c8966a71b0d633d272bc6b0e242a4 page a7
ABB i-bus
KNX
Planning and application
DLR/S 8.16.1M | 2CDC507100D0203 165
4.6 Burning-in of lighting equipment
In the case of lamps filled with gas, a burn-in time is recommended. This burn-in process is only required
once at the start of commissioning.
Only after this burn-in time do fluorescent lamps have a stable operating value, which ensures the best
possible dimming behavior and an optimum service life. An optimum pressure level is created in the
fluorescent tube by burn-in.
For installations with dimmable ballasts, many lamp manufacturers make a recommendation that a burn-in
time of 20 to 100 hours must be observed. The recommended values are about 20 hours for T8 lamps and
100 hours for T5 lamps. The exact values are available from the lamp manufacturers. During the burn-in
time, the lamps are only switched on at maximum capacity. Dimming is not possible.
The information about burn-in times can often not be found in the catalogue of the lamp manufacturer but
in the descriptions of the electronic ballasts, as the burn-in time only becomes relevant with dimmable
systems. Stable operating values and reproducible brightness values are a prerequisite in these
installations. Moreover, only poor evaporation of the solid or fluid additives is possible for dimmed lights
due to the reduced capacity, so that in certain circumstances the maximum light yield is only achieved at a
later date or not at all. This can lead to the complete replacement of the lamps.
According to statements of lighting planners, if fluorescent lamps (particularly T5 lamps) are not burned in,
they can even be damaged, causing them to fail prematurely.
With the DALI Light Controller, it is possible to activate a burn-in time via the communication object Burn-in
lamps/Status and to place individual lighting groups or all lighting groups on the DALI Light Controller in
the burn-in state. The lighting groups, which are considered for the Burn-in function, can be set via
parameters. During this time, the lamps can only be switched on with 100 % or switched off. Dimming is
not possible.
The Burn-in function can be activated for all the lighting groups together (DALI output) or by using an
additional communication object for each lighting group individually (group x). In the Parameter window Gx
Group, page 67, every lighting group can be approved for burn-in with the parameter Enable central
function Burn-in object "Burn-in lamps/Status". The activation of the Burn-in function can be undertaken
centrally via the communication object DALI output or per lighting group via the Group x communication
objects.
The DALI Light Controller features a separate hour counter (1…255 h) for each individual DALI device for
the Burn-in function. The accuracy of the timing is set internally to five minutes, even though the time is
counted in hours. The DALI Light Controller only indicates the burn-in state but not the remaining or
elapsed burn-in time.
If the lamp is switched off during the activated burn-in time, the burn-in counter stops the counting process.
Should the lamp be switched on again, the counting process will continue and the remaining time will be
rounded off to the nearest five minute step.
On light controller supply voltage failure or KNX bus voltage failure on the DALI Light Controller, the
elapsed burn-in time is stored and continues to be used after voltage recovery. The same applies after a
download.

Chat with your ABB DLR/S 8.16.1M manual using AI

Get instant AI answers from your ABB DLR/S 8.16.1M manual

Ask anything about the ABB DLR/S 8.16.1M. Answers come from this manual, with the pages they are based on.

DLR/S 8.16.1M Maintenance Schedule

As needed
Clean the device housing

If devices become dirty, clean them using a dry cloth or a cloth dampened with a soapy solution. Never use corrosive agents or solutions.

Show in the manual (page 26)
One-time at commissioning
Perform lamp burn-in procedure

Operate lamps at 100% brightness for a recommended period (e.g., 20-100 hours) to ensure stable operating values and optimal service life before dimming is used.

Show in the manual (page 167)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend DLR/S 8.16.1M?

Yes No

Frequently Asked Questions

A

Up to sixty-four DALI devices can be connected to the single DALI output of this controller unit efficiently.

Is this answer helpful?

A

Yes, fourteen independent light scenes are supported and recallable via KNX telegrams for customized lighting scenarios.

Is this answer helpful?

A

Yes, manual operation is available via front panel buttons unless specifically disabled by a KNX parameter setting.

Is this answer helpful?

A

Yes, reaction to voltage failure is parameterizable to determine behavior when bus voltage drops unexpectedly.

Is this answer helpful?

A

Supported with customizable curves including pre-warning phases and basic brightness retention after activation.

Is this answer helpful?

A

Coded messages are sent via KNX communication objects to report lamp and ballast malfunctions clearly.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Supports up to 64 DALI devices across 16 lighting groups for scalable installation.
  • Enables constant light control using integrated sensors for energy efficiency.
  • Offers manual operation buttons for local device control and troubleshooting.
  • Facilitates master-slave dimming setups with adjustable brightness offsets.
  • Includes fourteen programmable light scenes accessible via KNX telegrams.
VS

Disadvantages

  • Requires dedicated software tool for DALI addressing and group assignment tasks.
  • Overlapping lighting groups function is not supported by the controller unit.
  • Configuration requires specific KNX interface hardware and ETS software access.
  • Manual operation is disabled if blocked by specific communication object setting.
  • Fault messages may take up to 45 seconds to reset upon remediation.
M: QW-35-FL

Product Specification

Type

Actuator

Standard

KNX

Function

Switch Actuator (on/off), Dimming Function

Topology

Bus

Dimensions

4.25 x 3.54 x 2.54 in

Features

IP20

M: QW-35-FL

Product Description

Intelligent Lighting Solutions

Modern building automation relies heavily on efficient lighting management. The ABB DLR/S8.16.1M DALI Light Regulator 8-fold, 6TE REG, Switch Actuator with Dimmer Manual provides essential guidance for this integrated solution. This controller connects digital illumination standards with KNX installation protocols. It supports up to sixty-four DALI devices across sixteen distinct lighting groups. Energy conservation is prioritized through constant light control features paired with eight light sensors. Automatic detection adjusts artificial brightness to match daylight conditions perfectly. Users gain enhanced comfort alongside operational cost reductions. Intelligent algorithms ensure optimum working environments remain stable regardless of external weather changes.

Key Functionalities

Versatile scene recalls occur via bit telegrams frequently. Fourteen independent light scenes allow custom settings stored quickly. Staircase lighting functions offer pre-warming phases and warning signals automatically. Master-slave operations facilitate complex dimming setups with offset controls for secondary strips. Fault monitoring ensures individual lamp status reports reach the central system efficiently. Manual overrides exist for emergency adjustments directly on the device faceplate. Software tools assist in configuring addresses without complex engineering knowledge initially.

Technical Specifications

Robust mounting occurs on thirty-five millimeter rails consistently. Protection classes ensure safety against dust and water ingress effectively. Power consumption remains low while maintaining high performance metrics. Communication objects enable status feedback loops throughout the network architecture. Voltage failure reactions are parameterizable to suit specific site requirements. Burn-in functions guarantee initial lamp longevity and stability over time. Replacement units can be addressed automatically if configured correctly beforehand. Comprehensive diagnostics help identify ballast malfunctions instantly for quick repairs.

Implementation Details

Benefits stem from flexible grouping capabilities inherent to design. Lighting circuits adapt to room usage changes without rewiring infrastructure. Calibration processes involve both artificial light and natural daylight parameters. Overhead sensors capture accurate readings without glare interference effectively. System reliability increases with internal buffering during power fluctuations. Installation experts utilize push-in terminals for secure electrical connections quickly. Regular maintenance keeps performance optimal across extended project lifecycles. Integration with existing KNX networks streamlines whole-building control strategies effectively. Smart solutions drive sustainability goals forward in modern commercial structures globally.

Final Notes

Commissioning requires proper configuration tools and physical access points. Programming happens through specialized interfaces designed exclusively for this hardware platform. Data transfer occurs securely between controllers and central management units. Visualization systems receive real-time updates regarding operational status continuously. Troubleshooting procedures utilize detailed error logs stored within internal memory registers. Future expansion plans accommodate additional modules without disrupting current operations significantly. Regulatory compliance meets international safety standards for electronic equipment deployment worldwide.

M: QW-35-FL

© Copyright 2026 Manual.ly