Manual.ly Logo

Zipper ZI-BAS205 Manual

0.0 · 0 Ratings

PDF manual · 131 Pages

English

M: OA-GPT-5-NAN
page

/ 131

Loading...
f3a6d3cb359d07a6a06790b1ea83f41cf7f7 page 23
PREFACE (EN)
ZIPPER MASCHINEN GmbH www.Zipper-Maschinen.at 35
ZI-BAS205 / ZI-BAS25035
12 PREFACE (EN)
Dear Customer!
This user manual contains information and important notes for safe start-up and handling of the
wood band saw model ZI-BAS250, ZI-BAS205 for simplification purposes hereinafter referred to
as "machine".
The manual is part of the machine and must not be removed. Keep it for later use
in a suitable place, easily accessible to users (operators), protected from dust and
moisture, and enclose it with the machine if it is passed on to third parties!
Pay special attention to the chapter Safety!
Due to the constant further development of our products, illustrations and contents may differ
slightly. If you notice any errors, please inform us.
Technical changes reserved!
Check the goods immediately after receipt and note any complaints on the
consignment note when taking over the goods from the deliverer!
Transport damage must be reported separately to us within 24 hours.
ZIPPER-MASCHINEN cannot accept any liability for unnoticed transport damage.
Copyright
© 2020
This documentation is protected by copyright. All rights reserved! Especially the reprint, the
translation and the extraction of photos and illustrations will be prosecuted.
The place of jurisdiction shall be the Regional Court of Linz or the court responsible for 4707
Schlüsselberg.
Customer service contact
ZIPPER MASCHINEN GmbH
Gewerbepark 8, A-4707 Schlüsslberg
AUSTRIA
Tel.: +43 7248 61116-700
Fax: +43 7248 61116–720
Mail: info@zipper-maschinen.at

Chat with your Zipper ZI-BAS205 manual using AI

Get instant AI answers from your Zipper ZI-BAS205 manual

Ask anything about the Zipper ZI-BAS205. Answers come from this manual, with the pages they are based on.

ZI-BAS205 Maintenance Schedule

Remind me when maintenance is due
Monthly
Inspect drive belt condition

Check the drive belt for wear and proper tension; replace if necessary.

Show in the manual (page 32)
Monthly
Check safety stickers

Verify all warning and safety labels are legible and intact; replace if damaged.

Show in the manual (page 32)
Monthly
Inspect table insert

Examine the table insert for damage or enlarged slots and replace if needed.

Show in the manual (page 32)
Monthly
Inspect thrust bearing and guides

Check thrust bearing and guide discs for wear and replace them if worn out.

Show in the manual (page 32)
Before every use
Check safety devices and connections

Verify safety equipment, electrical cables, and screw connections are intact and tightened before starting work.

Show in the manual (page 28)
After every use
Clean chips and dust from machine

Remove wood chips and sawdust from the cutting area, table insert, and wheel housings using a vacuum.

Show in the manual (page 32)
After every use
Lubricate saw band guide

Apply a small amount of acid-free lubricating oil to the saw band guide components.

Show in the manual (page 32)
After every use
Keep guides free of deposits

Ensure thrust bearing and guide discs remain free of debris or buildup.

Show in the manual (page 32)
After every use
Release saw blade tension

Detension the saw blade to protect wheel running surfaces and attach a warning sign.

Show in the manual (page 28)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: QW-35-FL

Ask a Question

0/1000

Do you recommend ZI-BAS205?

Yes No

Frequently Asked Questions

A

The ZI-BAS205 supports sawband widths from 3.5 mm to 12 mm and a sawband length of 1400 mm. Choose narrower blades for tight curves and wider blades for straight cuts.

Is this answer helpful?

A

Operate from a grounded 230–240 V, 50 Hz supply with RCD protection (max 30 mA). Use recommended extension-cable cross-sections for cable lengths and have electrical connections or repairs performed by a qualified electrician.

Is this answer helpful?

A

Maximum cutting height is 80 mm at 90° and 45 mm at 45° tilt. They are subject to correct blade selection and proper setup of tension and guides.

Is this answer helpful?

A

Disconnect power, fit the blade and tension via the hand wheel. Adjust tracking by tilting the upper wheel using its hand wheel until the blade runs centered on the wheels; then lock the handwheel. Tension varies by blade width—follow the manual’s guidance and run the machine briefly to verify alignment.

Is this answer helpful?

A

Yes. The saw must be connected to a dust and chip extraction system. Recommended airspeed at the port is at least 20 m/s for dry chips (higher for wetter chips). Use antistatic, flame-retardant hoses and ensure the extractor starts with the saw.

Is this answer helpful?

A

No. Wearing gloves on rotating parts is prohibited. Use a push stick to keep hands clear; gloves are allowed only for handling blades or non-rotating tool changes as specified.

Is this answer helpful?

A

Before each use, inspect safety devices, blade condition, tension and guide settings. Clean chips after each run, monthly check belts and fasteners, and replace worn table inserts or belts as listed in the maintenance schedule.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Compact footprint with 195 mm throat and 80 mm cutting height at 90°—good for small workshops.
  • Accepts 3.5–12 mm blade widths, enabling both tight-radius curve cutting and straight ripping.
  • Safety interlocks on upper and lower doors plus adjustable blade guard (max 3 mm to workpiece).
  • Clear adjustment procedures for tracking, blade tension, upper/lower guide alignment and table tilt.
  • Integrated dust-extraction port and specifications for required airflow to reduce wood dust hazards.
VS

Disadvantages

  • 250 W motor (S2) limits heavy continuous cutting compared with higher-power workshop saws.
  • Blade length limited to 1400 mm; larger projects may require a larger saw model.
  • IP20 rating and modest sound insulation—requires care in noisy or damp environments.
  • Some maintenance tasks and electrical connections require a qualified electrician.
  • Not designed for cutting metal or other materials outside wood-like physical properties.
M: OA-GPT-5-NAN

Product Specification

Type

Bandsaw

Power

250W (230V)

Band speed

3116.80 ft/min

Saw blade length

55.12in

Cutting capacity

max. 3.15in

Blade tilt

45°

Dimensions

11.81x25.20x15.35in (WxHxD)

Weight

40.34lb

Scope of delivery

Push stick

M: OA-GPT-54-NAN

Product Description

Zipper ZI-BAS205 Electric Band Saw — Powerful, Precise, Workshop-Ready

The Zipper ZI-BAS205 Electric Band Saw is a compact yet capable woodband saw engineered for accurate longitudinal, cross and curved cuts in wood and similar materials. Designed for hobbyists, small shops and light professional use, the machine balances a robust build with user-focused features: a protected blade guard, adjustable worktable with 0°–45° tilt, dust extraction port and clear safety interlocks on upper and lower doors.

With a 250 W motor (S2 duty) and a saw throat of 195 mm, the ZI-BAS205 handles typical woodworking tasks including thin rip cuts, miters, tenons, wedges and template-driven profiles. The machine accepts blade widths from 3.5 to 12 mm and blade length of 1400 mm, giving good versatility for curve cutting or straight ripping. Important ergonomic touches include a rip fence, a bench angle gauge, a removable table insert and push stick for safe small-piece feeding.

The saw emphasizes safety and maintenance: door safety switches disable the motor when front doors are opened, the upper blade guard must be set within 3 mm of the workpiece for optimal protection, and guidance explains proper blade tensioning, tracking and guide adjustment for consistent, vibration-free cuts. Electrical guidance recommends operation from a earthed 230–240 V supply with RCD protection and specific extension-cable gauges for safe power delivery.

Practical setup and upkeep instructions simplify long-term use: secure the machine to a firm, level surface, ensure dust extraction (minimum airflow guidance included), check blade condition and replace worn or deformed blades immediately, and follow the provided maintenance schedule for checks on belts, bearings and fasteners. For the ZI-BAS205 the manual details blade changing, tracking adjustments, upper/lower blade guide alignment and table leveling so users can maintain accuracy and prolong blade life.

Overall this band saw is a focused tool for precise wood cutting in constrained spaces. It pairs safety features and clear service guidance with the flexibility needed for common woodworking operations, making it a reliable choice for workshops seeking a small footprint bandsaw that still offers quality results.

Notes

  • Always use appropriate personal protective equipment (eye protection, dust mask, hearing protection). Do not use gloves near rotating parts.
  • Ensure dust extraction is connected and running before operation; follow recommended air speeds for effective extraction.
  • Only operate, wire or repair electrical components by qualified personnel; observe grounding and RCD requirements.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly