Manual.ly Logo

X-Lite X-1005 Ultra Carbon Manual

0.0 · 0 Ratings

PDF manual · 128 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 128

Loading...
fe05a31de8477c12db324fb4b849ae558980 page 17
23
X-1005
6.4 Repeat these steps with the padding of the right cheek pad.
Warning: the buttons are not fastened until a click is heard. Check that the strap
comes out properly from the cheek pad padding.
6.5 Insert the chin strap band into the elastic loop on the cheek pad strap (Fig. 13).
WARNING
- If your helmet is equipped with the D-Ring retention system, pull it down as
indicated in the attached D-Ring label.
- Remove the inner comfort padding only when cleaning or washing is required.
- Never use the helmet if the inner comfort padding and the cheek pads have not
been correctly and completely tted.
- Carefully wash by hand and use only neutral soap and water at 30° max.
- Rinse using cold water and dry at room temperature, away from direct sunlight.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material. It is apt to change or get
partially destroyed to help absorb shocks.
- Do not modify or alter the internal polystyrene components in any way.
- Clean the inner polystyrene components using a damp cloth only and allow it to
dry at room temperature away from direct sunlight.
- Never use tools or equipment of to carry out the steps described above.
LINER POSITIONING CONTROL (LPC)
1 ADJUSTING THE POSITION OF THE LINER
The different anatomic shape of riders heads at times requires the position of the hel-
met to be adapted to the head in question. The LINER POSITIONING CONTROL (LPC)
enables the position of the liner to be adjusted. This means that, unlike a standard
helmet, the position of the helmet on the rider’s head can be changed without changing
the size of the helmet, making it adaptable to multiple needs.
To adjust the liner, proceed as follows after releasing the rear part of the liner (see
instructions above).
1.1 Release the liner adjustment rear ap from the central locking pin on the rear frame
of the liner (Fig.22).
1.2 Pull the adjustment rear ap and fasten it to the central pin in one of the other 7
possible snap positions.
By pulling the adjustment rear ap of the liner, the helmet is gradually posi-
tioned higher on the head snap after snap.
1.3 Fully reassemble the liner into the helmet (see instructions above) being careful to
correctly insert the adjustment ap into the cavity between the outer shell and the
polystyrene inner shell.
1.4 Put on the helmet and check that the helmet is comfortable and suitably posi-
tioned. If it is not, adjust it again.
WARNING
After adjusting the position of the liner, put on and fasten the helmet to check the correct adjust-
ment of the chin strap (see attached label), the correct positioning of the helmet on your head
in the riding position and the taking off (see “SAFETY AND INSTRUCTIONS FOR USE” above)
.
INSTRUCTIONS FOR USE

Chat with your X-Lite X-1005 Ultra Carbon manual using AI

Get instant AI answers from your X-Lite X-1005 Ultra Carbon manual

Ask anything about the X-Lite X-1005 Ultra Carbon. Answers come from this manual, with the pages they are based on.

X-1005 Ultra Carbon Maintenance Schedule

After every use
Dry helmet and visor

Leave helmet to dry in a ventilated, dry place with visor open. Keep away from heat sources.

Show in the manual (page 18)
Periodically
Check PINLOCK stretch

Open and close visor to ensure correct stretch and prevent scratching between surfaces.

Show in the manual (page 18)
When damaged
Replace scratched visor or PINLOCK

Replace if deeply scratched or damaged as it reduces visibility and compromises protection.

As needed
Wash inner comfort padding

Remove padding only for washing. Hand wash with neutral soap and water max 30C. Do not machine wash.

Show in the manual (page 23)
As needed
Clean polystyrene liner

Clean internal polystyrene components only with a damp cloth. Do not modify or alter them.

Show in the manual (page 23)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend X-1005 Ultra Carbon?

Yes No

Frequently Asked Questions

A

Use lukewarm water and neutral soap only. Dry at room temperature away from direct sunlight. Never use solvents like petrol or benzene as they damage materials.

Is this answer helpful?

A

The Vision Protection System is an internal sunshade made of LEXAN. It allows you to reduce light transmission without removing the outer visor, useful during bright days.

Is this answer helpful?

A

Replace the helmet after any accident where integrity is in doubt or if damage is visible. Even invisible impacts can compromise the polystyrene liner.

Is this answer helpful?

A

No. Modifications void the warranty and may reduce protection. Only use original accessories and spare parts compatible with this specific model version.

Is this answer helpful?

A

It uses upper, lower, and rear vents. Lower vents channel air to the visor, upper vents diffuse air, and the rear spoiler exhausts hot air for comfort.

Is this answer helpful?

A

Yes, certain versions are pre-wired for N-Com kits. You must remove specific foam fillers from cheek pads to install the speakers correctly.

Is this answer helpful?

A

Install the PINLOCK inner visor correctly. Ensure silicone seals are clean and stretched properly. Keep the helmet dry inside after use.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Advanced ventilation system with upper, lower, and rear exhaust channels
  • Unique dual action chin guard mechanism for one-handed safety operations
  • Integrated Vision Protection System reduces glare without removing visor
  • Removable and washable inner liner and cheek pads for hygiene
  • Compatible with PINLOCK anti-fog inner visor system for clear sight
VS

Disadvantages

  • Complex fitting process for eyewear adaptive padding requires care
  • VPS sensitivity to high heat requires specific storage conditions
  • Manual specifies helmet replacement after impacts even with no visible damage
  • Dual action lever adjustment requires checking every time for security
  • Padding removal requires careful reassembly to avoid fit issues later
M: qwen/qwen3.5-flash-20260224

Product Specification

Type

Modular helmet

Features

Integrated visor

M: qwen/qwen3.5-flash-20260224

Product Description

Discover the X-Lite X-1005 Ultra Carbon

Welcome to the ultimate riding experience with the X-Lite X-1005 Ultra Carbon. This premium helmet combines advanced safety with superior comfort for the modern rider. When you refer to the X-Lite X-1005 Ultra Carbon Manual found inside the package, you will find detailed guidance on maximizing your gear performance every single day. The design prioritizes ergonomics and aerodynamics to reduce fatigue during long rides across varied terrain.

Key Safety Features

Safety remains paramount for all our products. The helmet meets strict ECE 22-05 standards for protection on roads. It features a unique dual action system for the chin guard, allowing one-handed operation while preventing accidental opening from wind pressure. This mechanism ensures stability during high-speed riding situations. In case of impact, the shell absorbs energy, though no helmet guarantees absolute safety. Always replace the helmet after an accident if integrity is doubtful or damaged visibly. Modifications void all warranties and protection standards. Avoid altering the polystyrene layers.

Comfort and Adjustability

Internal comfort is highly adjustable for diverse head shapes. The liner positioning control allows fine-tuning the helmet height on your head for better stability. Removable cheek pads and liner make washing easy, using only neutral soap and lukewarm water at thirty degrees Celsius. Airflow is managed through upper, lower, and rear ventilation channels integrated into a spoiler. The rear exhaust clears hot air effectively. For eyeglasses wearers, the eyewear adaptive feature creates space without removing padding. Ensure padding is dry before reassembly to prevent mold growth inside the helmet material.

Optical Protection

The Vision Protection System, or VPS, offers sun protection without removing the outer visor. It can be activated or deactivated smoothly using a slider. For clear vision at night or in fog, the PINLOCK inner visor system helps prevent condensation between layers. Maintain the silicone seals carefully to avoid scratches that affect visibility. Use only specific cleaning solutions for the polycarbonate material. Do not let raindrops sit on the VPS as it reduces clarity quickly during rainfall conditions on the road.

Maintenance Instructions

Clean the visor and shell using warm water and mild soap strictly. Avoid chemicals like petrol, thinner, or benzene that damage the structural integrity. Keep the helmet away from heat sources like exhaust pipes. If you experience fogging, check the PINLOCK installation and stretch regularly. Following the X-Lite X-1005 Ultra Carbon Manual instructions ensures longevity of the shell and pads. Always ensure the retention strap is snug but comfortable below the chin. Regular checks prevent accidents and ensure compliance with safety norms while riding motorcycles or motorbikes. Ride safely and enjoy the technology provided by this excellent piece of engineering designed for modern motorcyclists worldwide who demand quality assurance in their gear selection.

Notes

Store the helmet in a cool, dry place. Inspect screws regularly. If the VPS feels hard, check temperature sensitivity.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly