Manual.ly Logo

Wagner Control Pro 350 M Manual

5.0 · 1 Ratings

PDF manual · 144 Pages

English

M: OA-GPT-54-NAN
page

/ 144

Loading...
91ef9f022cd4fdd3c9d0f05020561dfdc88f page 11
D
11
Control Pro 350 M
8. Drehen Sie den Wahlschalter in die Position PRIME (senkrecht).
9. Halten Sie die Spritzpistole an den Rand des Reinigungsbehälters.
10. Ziehen Sie den Abzugsbügel und halten Sie den Abzugsbügel so lange gedrückt, bis nur noch klare Flüssigkeit austritt.
11. Schalten Sie das Gerät aus und ziehen Sie den Netzstecker.
12. Drehen Sie den Wahlschalter in die Position PRIME (senkrecht).
13. Ziehen Sie den Abzugsbügel, um eine Druckentlastung durchzuführen.
14. Sichern Sie die Spritzpistole.
15. Trennen Sie die Spritzpistole mithilfe von Schraubenschlüsseln (13) vom Farbschlauch.
i
Falls das HEA Filter Set verwendet wird dieses entsprechend den Informationen im Kapitel "HEA Filter Set" demon-
tieren und reinigen.
16. Entfernen Sie die Düse (1), Unterlegscheibe (2) und die Halterung (3) aus dem Düsenhalter (4) und reinigen Sie alle Teile
gründlich. (Abb. 21)
17. Setzen Sie die Halterung und die Unterlagsscheibe wieder in den Düsenhalter ein.
Schrauben Sie den Düsenhalter auf die Pistole.
18. Entfernen Sie den Ansaugschlauch vom Grundgerät.
19. Entfernen Sie den Rücklaufschlauch.
20. Wischen Sie beide Schläuche von außen ab.
21. Ziehen Sie die Filterscheibe (1) vorsichtig aus dem Ansauglter heraus. (Abb. 22)
22. Reinigen Sie die Filterscheibe gründlich unter ießendem Wasser.
23. Entfernen Sie den Hochdruckschlauch mit einem Schraubenschlüssel (17) vom Grundgerät.
24. Tauchen Sie das Einlassventil in einen mit Konservierungsmittel (z.B. Haushaltsöl) gefüllten Behälter ein. (Abb. 23)
25. Stecken Sie den Netzstecker ein.
26. Halten Sie ein Tuch vor den Schlauchanschluss und schalten Sie das Gerät für ca. 5 Sekunden ein. (Abb. 24)
Die Pumpe wird durch diesen Vorgang konserviert.
Wartung und Reparaturen
Gefahr
Vor allen Arbeiten am Gerät Druckentlastung durchführen und den Netzstecker aus der Steckdose ziehen.
a) Reinigung Einlassventil
i
Wenn beim Ansaugen des Materials Probleme auftreten, muss gegebenenfalls das Einlassventil gereinigt oder
ersetzt werden. Probleme können vermieden werden, wenn das Gerät immer ordnungsgemäß gereinigt und
gewartet wird.
1. Entfernen Sie den Ansaugschlauch vom Grundgerät.
2.
Entfernen Sie das Einlassventil (Abb. 25, 1) mit einem Schraubenschlüssel (20) oder Innensechskantschlüssel (10 mm) vom
Grundgerät.
3. Entnehmen Sie Ventilsitz (Abb. 25, 2), Kugel (3) und O-Ring (4) aus dem Einlassventil.
4.
Reinigen Sie die Aufnahme für das Einlassventil und alle Bauteile gründlich mit einer geeigneten Reinigungslösung bzw. tauschen
Sie sie bei Bedarf aus.
5. Fetten Sie den O-Ring (Abb. 25, 5) am Einlassventil ein.
6. Setzen Sie Ventilsitz, Kugel und O-Ring wieder in das Einlassventil ein.
7. Drehen Sie das Einlassventil wieder in das Spritzgerät.
b) Reinigung Auslassventil
i
Bei einem schlechten Sprühbild, muss gegebenenfalls das Auslassventil gereinigt oder ersetzt werden. Probleme
können vermieden werden, wenn das Gerät immer ordnungsgemäß gereinigt und gewartet wird.
1. Entfernen Sie den Hochdruckschlauch mit einem Schraubenschlüssel (17) vom Grundgerät.
2. Lockern Sie die Schraube (Innensechskantschlüssel 2,5 mm) am Auslassventil (Abb. 26), entfernen Sie sie aber nicht.
3. Entfernen Sie das Auslassventil (Abb. 27, 1) mit einem Schraubenschlüssel (16) vom Grundgerät.
4. Reinigen Sie die Aufnahme für das Auslassventil und das Auslassventil gründlich mit einer geeigneten Reinigungslösung bzw.
tauschen Sie das Auslassventil bei Bedarf aus.
5. Setzen Sie das neue oder gereinigte Auslassventil wieder ein.
6. Ziehen Sie die Schraube (Abb. 26) wieder fest.

Chat with your Wagner Control Pro 350 M manual using AI

Get instant AI answers from your Wagner Control Pro 350 M manual

Ask anything about the Wagner Control Pro 350 M. Answers come from this manual, with the pages they are based on.

Control Pro 350 M Maintenance Schedule

After every use
Clean the entire unit and components

Clean the device immediately after work ends. Remove nozzle holder, clean filters, suction hose, high-pressure hose, and inlet valve with appropriate solution.

Show in the manual (page 16)
After every use
Preserve the pump

Immerse the inlet valve in conservation agent like household oil and run the pump for 5 seconds to preserve internal parts.

Show in the manual (page 17)
Before each use
Inspect the high-pressure hose

Check the hose thoroughly for wear, kinks, or leaks before every operation. Replace damaged hoses immediately.

Show in the manual (page 10)
Every 6 years
Replace the high-pressure hose

Wagner recommends replacing the high-pressure hose after 6 years due to increased risk of damage from aging.

Show in the manual (page 11)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Control Pro 350 M?

Yes No
0
User Pic

Klaus Richter

8 months ago

How is the price-performance and customer service, and is the delivery really reliable?

0
User Pic

Manual.ly

8 months ago

We are committed to strong value for money and a smooth shopping experience. Many customers mention the product quality compared to the price as a key benefit. For service, our team responds promptly and helps with questions or any issues that may come up. Delivery is handled carefully and shipped efficiently; you can typically follow the shipment so you know when it is on the way. If anything is not right, contact support and we will work with you to resolve it quickly.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

It is best for spraying interior walls and outdoor surfaces like fences or garage doors. It handles larger DIY painting projects where speed, even coverage, and a professional-looking finish are important.

Is this answer helpful?

A

It can spray dispersion and latex paints, lacquers, glazes, oils, primers, rust protection coatings, and other compatible water-based or solvent-based materials. The right nozzle and filter should match the coating.

Is this answer helpful?

A

Sometimes. Many wall paints may need slight thinning, while some lacquers and glazes can be used undiluted. The ideal ratio depends on the material, so a spray test is recommended before starting.

Is this answer helpful?

A

PRIME is used to prefill the system with paint and to release pressure from the hose and gun. It is the safe position to use before setup, cleaning, or whenever you need to depressurize the unit.

Is this answer helpful?

A

Turn the reversible nozzle 180 degrees, switch to PRIME briefly to reduce pressure, then return to SPRAY and spray into cardboard or scrap wood. This can clear the blockage without touching the tip.

Is this answer helpful?

A

Very important. Immediate cleaning prevents dried paint from blocking the filter, hose, nozzle, or valves. Proper cleaning also helps maintain spray quality and supports the long-term life of the sprayer.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • High-pressure airless spray system helps cover large areas quickly with a smooth, even finish.
  • Works with a wide range of coatings, including wall paint, lacquer, glaze, oil, and rust protection.
  • Includes practical features like a telescopic handle, 15 m hose, and onboard storage for accessories.
  • HEA Filter Set and interchangeable nozzles improve spray quality and reduce clogging.
VS

Disadvantages

  • Requires careful safety handling because airless spray pressure can cause serious injection injuries.
  • Cleaning and pressure relief steps are time-sensitive and must be followed closely after every use.
  • Not suitable for flammable materials, abrasive coatings, acids, or heavily solvent-rich mixes.
  • Performance depends on correct thinning, nozzle choice, grounding, and regular maintenance.
M: OA-GPT-54-NAN

Product Specification

Power

600W

Flow rate

0.40 gal/min

Paint application

80.73 ft^2/min

Paint cup

no

Special features

Airless, Suction connection

Scope of delivery

2x nozzle set, hose (49.21 ft)

M: OA-GPT-54-NAN

Product Description

Wagner Control Pro 350 M: Efficient Airless Painting for Bigger DIY Projects

The Wagner Control Pro 350 M Airless Electric Paint Spraying System Manual highlights a machine built for users who want fast, even coating without the fatigue of constant brushwork. This airless sprayer is designed for interior walls, fences, garage doors, and other medium-to-large painting jobs where speed and finish quality matter. With its 230 V motor, 600 W power input, and maximum spray pressure of 110 bar, it delivers strong performance while remaining practical for home renovators and ambitious DIY painters.

What makes this system appealing is its balance of power and control. The pressure regulator lets you fine-tune output depending on the material, while the PRIME and SPRAY settings make startup, priming, and pressure relief straightforward. The unit is also equipped with a 15 m high-pressure hose, a telescopic handle, and a built-in storage area for nozzles and small parts, which adds convenience during real-world use.

The sprayer is compatible with a wide range of coating materials, including dispersion and latex wall paints, lacquers, glazes, oils, and rust protection coatings. It also supports different nozzle and filter combinations, such as the 311 nozzle for thinner materials and the 517 nozzle for thicker paints. This flexibility helps users achieve a cleaner spray pattern and better material flow across different surfaces. The optional HEA Filter Set is another practical touch, reducing nozzle clogging and helping maintain a steadier finish.

Of course, the system demands careful handling. Like all airless sprayers, it operates at very high pressure, so safety steps are essential. Proper grounding, ventilation, protective gloves, eye protection, and respiratory protection are all strongly recommended. Regular cleaning is equally important, since dried paint can affect performance and shorten the life of parts like filters, valves, and nozzles.

For users who value consistent coverage and want to cut down on painting time, the Control Pro 350 M offers a strong mix of precision, efficiency, and versatility. It is especially well suited to anyone tackling renovation work and looking for a dependable airless spray solution.

Notes

  • Best for interior wall paint, lacquers, and similar coatings
  • Always relieve pressure before cleaning or maintenance
  • Use the correct nozzle and filter for the material
  • Clean immediately after use to protect performance and warranty
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly