Manual.ly Logo

Vitavia Playa 5900 Manual

0.0 · 0 Ratings

PDF manual · 40 Pages

English

M: QW-35-FL
page

/ 40

Loading...
c744339fb9e6ec61c8d16ad739ca0b00aff6 page 6
6
Assembly Instructions
SITE SELECTION
Always try to select a sunny location, sheltered
from the wind as much as possible.
IMPORTANT
Before assembling your new greenhouse,
please check that all parts in the provided list
are included. Please take each bundle out of
the packaging in order to identify the parts
better.
It is important that the opened bundles do not
get mixed with one another.
If something is missing please contact your
retailer.
Important! The UV-resistant side of the
polycarbonate panes is indicated by the plastic
lm and printing at the edge. This side must
face outside. Remove the lm.
Nuts (1002) - Max. tightening torque 3Nm.
NECESSARY TOOLS
Screw drivers (Normal and Crosshead PH2),
10 mm socket spanner or wrench, 10 mm
combination spanner, knife, measuring stick,
spirit level, ne tooth saw, Accu-drill with
adjustable torque.
MAINTENANCE
The greenhouse should be thoroughly washed
with a gentle detergent occasionally. Please
check that the detergent used does not react
aggressively with aluminium or the glass xing
clips.
Ensure that the upper and lower door tracks
are cleaned regularly to avoid a build up of
debris.
0A. BASE
Important! The base must be exactly square
and level.
(Attention! Only when the greenhouse has to
be located in a very windy and unprotected
location: Drill through both the prole at the
base of the greenhouse and the steel base,
and connect them with nuts and bolts.)
If you would rather construct your own stone
or concrete foundation, please follow the
dimensions as specied in diagram 0A.
If you choose to use the anchor legs supplied
with the steel base please make a hole at
each point marked C. These will be lled with
concrete after the assembly of the house is
completed.
Foundations must extend down below the frost
level.
Diagrams in a single frame show the view
from inside the greenhouse. Those
enclosed in a double frame show the view
from outside the greenhouse.
0B. STEEL BASE
A zinc-coated steel base is delivered with the
greenhouse.
We recommend the use of the anchor legs
(9101), (9144) and (9145).
Assemble the parts as shown using bolts
(1001) and nuts (1002).
Important! Ensure that a space of 1218 mm is
left between the inside ends of base lengths
(9142) and (9143) in the front of the
greenhouse as shown.
Bend the ends of the anchor legs to provide a
secure connection in the concrete.
Position the completed base on the prepared
foundation.
(Attention! Concrete should be poured after
the house is completely assembled.)
1. PLAIN GABLE END
Lay all of the parts on the oor and connect
them loosely as shown.
Loosely connect the corner plates (1092) on
the upper corners (1.7).
2. SIDE ASSEMBLY
Loosely connect glazing bars (4232) between
the sill bars and horizontal bars.
3. DOOR GABLE END
Insert brush seal (4276) into the channel in
ridge bar (4250) (3.6).
Lay all of the parts on the oor and connect
them loosely as shown.
Please include 2 extra bolts in glazing bars
(2101) for the connection of brace (2092) (3.2)
and horizontal braces (2089 / 2090) (3.4).
Loosely connect the corner plates (1092) on
the upper corners (3.7).
4A. CONNECTING THE SEPARATE
ELEMENTS
Bolt the plain gable end (section 1), side
elements (section 2) and door gable end
(section 3) together (4.1) (4.4) (4.5) (4.6).
Assemble the diagonal braces (4233) (4.3)
and (4235) (4.2).
Loosely connect roof corner bars (4239 / 4240,
4245 / 4246) between the ridge bar (4250) and
eave bar (4226) using corner plates (1092)
(4.7) (4.10).
Loosely connect glazing bars (4241), (4242),
(4243), (4244), (4273) and (4274) between
horizontal bars (4271 / 4272, 4277 / 4278) and
roof corner bars (4239 / 4240, 4245 / 4246)
(4.8) (4.9).
4B. CONNECTING THE ROOF MIDDLE
BARS
Lift the assembled structure onto the prepared
steel base and connect loosely using clips
(9002) (4.11).
Loosely connect the door runner bar (2062) to
steel base lengths (9142) and (9143) using
bolts (2007) inserted into the (2062) bolt
channel (4.12) (4.13). The nuts (1002), inside
the base, will be tightened after the doors have
been positioned in section 5 (5.12).
Position and connect the roof glazing bars
(4254 / 4256) over and to the eave bar (4.18)
(4.19) and ridge bar (4.16) (4.17).
(5900) Note: It is necessary to include 2 extra
bolts in the bolt channel in glazing bars (4254)
at this point, to later connect the strengtheners
(4.16).
Loosely connect the gutter bar (4264) to roof
glazing bars (4254 / 4256) (4.18) (5900) (4.21)
(7600) and both roof corner bars (4239 / 4240,
1. PLEASE READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE ASSEMBLING YOUR GREENHOUSE.
2. Sharp edges and corners can cause injury. Always wear protective glasses, gloves, shoes and headgear when handling the aluminium proles, glass and
polycarbonate sheets. Broken glass is a safety hazard – always clear up immediately and dispose of with care.
3. The product you have purchased is intended only for growing plants and should only be used for this purpose. When used for other purposes we will take
no responsibility.
4. It is recommended that this greenhouse is assembled by two people.
5. Should you encounter difculties constructing this house, or in tting the glass or polycarbonate sheets, please contact your retailer
– do not use force!
6. The greenhouse must always be anchored.
Safety Warning
EN
092.01.1808

Chat with your Vitavia Playa 5900 manual using AI

Get instant AI answers from your Vitavia Playa 5900 manual

Ask anything about the Vitavia Playa 5900. Answers come from this manual, with the pages they are based on.

Playa 5900 Maintenance Schedule

Occasionally
Wash the greenhouse with gentle detergent

Thoroughly wash the greenhouse occasionally using a gentle detergent. Ensure the detergent does not react aggressively with aluminium or glass fixing clips.

Regularly
Clean door tracks to prevent debris buildup

Ensure that the upper and lower door tracks are cleaned regularly to avoid a build up of debris.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Playa 5900?

Yes No

Frequently Asked Questions

A

You will need screwdrivers (normal and crosshead PH2), a 10 mm socket spanner, a knife, a measuring stick, a spirit level, a fine tooth saw, and an accu-drill with adjustable torque.

Is this answer helpful?

A

The UV-resistant side must face outside. It is indicated by a plastic film and printing at the edge. Remove the film completely only after the pane has been positioned in the greenhouse.

Is this answer helpful?

A

It is strongly recommended that two people assemble the greenhouse to ensure safety and proper alignment of the heavy aluminum profiles and glass panels.

Is this answer helpful?

A

The maximum tightening torque for the nuts is 3 Nm. Over-tightening can damage the aluminum profiles or cause stress fractures in the polycarbonate sheets.

Is this answer helpful?

A

Yes, the greenhouse must always be anchored securely to the foundation using the provided anchor legs filled with concrete after assembly is complete.

Is this answer helpful?

A

No, neutral silicone is not included in the package. You must purchase it separately if you wish to seal the edges of the greenhouse for extra protection.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Durable 6mm polycarbonate glazing provides excellent insulation and light diffusion
  • Robust aluminum frame resists corrosion and structural deformation
  • Double sliding doors offer convenient access and space-saving design
  • Effective ventilation system prevents overheating and humidity buildup
  • Comprehensive multi-language manual simplifies the assembly process
VS

Disadvantages

  • Assembly requires two people and specific tools not included in the box
  • Foundation must be perfectly level and extend below the frost line
  • Polycarbonate film must be removed only after installation to prevent scratches
  • Maximum tightening torque of 3Nm requires careful monitoring to avoid damage
  • Silicone for sealing edges is not included and must be purchased separately
M: QW-35-FL

Product Specification

Glazing

Polycarbonate 6mm (hollow chamber sheets)

Frame

Aluminum

Color

Silver

Area

63.54 sq ft

Features

1 tilt-and-turn window, gutter, lockable

Door

Double sliding door

Dimensions (WxDxH)

8.46x7.54x7.58 ft

Delivery scope

Steel foundation

M: QW-35-FL

Product Description

Vitavia Playa 5900 HKP 6mm Greenhouse alu Manual

Creating a sanctuary for your garden has never been easier with the Vitavia Playa 5900 HKP 6mm Greenhouse. This robust structure combines durable aluminum framing with high-quality 6mm polycarbonate glazing to ensure optimal light transmission and thermal insulation for your plants throughout the year. Whether you are an experienced gardener or just starting out, this greenhouse offers a reliable environment that protects your crops from harsh weather while maximizing growth potential.

The assembly process is designed for clarity and safety. The manual guides you through selecting the perfect sunny location sheltered from strong winds, ensuring your greenhouse stands firm against the elements. Before beginning, it is crucial to verify all parts against the provided list and keep bundles organized to avoid confusion during construction. The aluminum profile requires careful handling due to sharp edges, so wearing protective gear is highly recommended.

A key feature of this model is its sturdy steel base, which must be placed on a level foundation extending below the frost line. The installation involves assembling the gable ends, side walls, and door sections before connecting them into a cohesive unit. Special attention is paid to the UV-resistant side of the polycarbonate sheets, which must face outward to protect the material from degradation. The roof strengtheners and gutter bars are installed to handle rainwater runoff efficiently, keeping the interior dry.

The double sliding doors provide easy access to your plants while maintaining a tight seal to retain heat. Proper adjustment ensures smooth operation without sticking. Additionally, the included vents allow for excellent air circulation, preventing overheating during summer months. Maintenance is straightforward; regular cleaning with mild detergent keeps the aluminum and polycarbonate looking new. Remember to secure the structure firmly to the ground and consider including it in your home insurance for complete peace of mind.

M: QW-35-FL

© Copyright 2026 Manual.ly