Manual.ly Logo

Telwin T-Charge 12 Manual

0.0 · 0 Ratings

PDF manual · 56 Pages

English

M: QW-35-FL
page

/ 56

Loading...
11fd248652b0f504f48e589da3e8a098e4e7 page 4
- 4 -
(EN)
INSTRUCTION MANUAL
WARNING: BEFORE USING THE BATTERY
CHARGER READ THE INSTRUCTION MANUAL
CAREFULLY.
1. GENERAL SAFETY RULES WHEN USING
THIS BATTERY CHARGER
- During the charge the battery produces
explosive gases, avoid the formation of
ames and sparkes. DO NOT SMOKE.
- Position the batteries to be charged in a well-
ventilated place.
- Inexperience and untrained people
should be properly instructed before
using the appliance.
- This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not
be made by children without supervision.
- Disconnect the mains cable before
connecting to or disconnecting the charging
cables from the battery.
- Do not connect or disconnect the clamps to
or from the battery with the battery charger
operating.
- Never use the battery charger inside the car
or in the bonnet.
- Substitute the mains cable only with an
original one.
- If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualied persons in order
to avoid a hazard.
- Do not use the battery charger to charge
batteries which are not rechargeable.
- Make sure the available power supply
voltage corresponds to that shown on the
battery charger rating plate.
- To avoid damaging the vehicle’s electronics,
read, keep and take very careful note of
the information supplied by the vehicle
manufacturer, when using the battery
charger either for charging or starting; the
same applies to the instructions supplied by
the battery manufacturer.
- This battery charger has components such as
switches and relays which can cause arcs or
sparks. Therefore when using it in a garage or
in a similar place set the battery charger in a
suitable case.
- Repair or maintenance of the inside of the
battery charger can be executed only by
skilled technicians.
- WARNING: ALWAYS DISCONNECT THE
POWER SUPPLY CABLE FROM THE MAINS
BEFORE CARRYING OUT ANY SIMPLE
MAINTENANCE OPERATION ON THE
BATTERY CHARGER.
2. INTRODUCTION AND GENERAL
DESCRIPTION
- This battery charger is used to charge
electrolyte free lead batteries used on motor
vehicles (petrol and diesel), motorcycles,
boats etc., and is designed for charging
sealed batteries.
- Rechargeable accumulators according to the
output voltage available: 6V / 3 cells; 12V / 6
cells.
- This model is a single phase 230V
50/60Hz battery charger, with constantly
electronically controlled current and voltage.
The charge voltage and current supplied by
the device have a IU charge curve.
- Standard features:
- The device allows you to connect dierent
types of output cables for the charging of
batteries:
- cables tted with eyelets (g. B-1);
- cables tted with clamps (g. B-2).
3. DESCRIPTION OF THE BATTERY CHARGER
Control, adjustment and indicator devices.
- Selecting the charge current/charge voltage:
Press the button seen in g. A-1 to set the
charge levels to 1A - 6V, 1A (
)12V, 4A
(
)12V: the LEDs seen in g. A-2 will
light up according to the selected charge
current.
Press and hold the button seen in g. A-1
for 3 seconds to enable the “AGM
” and
“RECOVERY
” (g. A-4) functions:
- The “AGM
” function is useful for
charging “AGM” type batteries: sealed lead
batteries, with electrolyte on absorbent
material, or for charging standard batteries
in low temperature conditions below 0°C
“COLD”.
- The “RECOVERY
” function, used at the
start of the charging process is designed to
recover sulphated batteries.
- Warning indications:
- Yellow LED (
) (g. A-5): polarity
reversal, Danger!!! Invert the charge
clamp connections!
- Orange LED “25%” (g. A-3): charge in
progress.
- Orange LED “50%” (g. A-3): charge in
progress.
- Green LED “75%” (g. A-3): charge in
progress.
- Green LED “100%” (g. A-3): charge
completed.
4. INSTALLATION
BATTERY CHARGER POSITION
- Place the battery charger in a stable position
during use.
- Do not lift the battery charger using the
power cable or charge cable.
CONNECTION TO THE MAINS
- The battery charger must only be connected
to a mains power supply with neutral
conductor connected to earth.
Make sure that the mains voltage is
equivalent to the operating voltage.
- The power line must have a protection
system, such as fuses or circuit breakers,
that can support the maximum apparatus
absorption.
- Use the relative power cable when
connecting to the mains.
- Any power cable extensions must be of
suitable size, never lower than that of the

Chat with your Telwin T-Charge 12 manual using AI

Get instant AI answers from your Telwin T-Charge 12 manual

Ask anything about the Telwin T-Charge 12. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend T-Charge 12?

Yes No

Frequently Asked Questions

A

Yes, this charger is designed for various motor vehicles including cars, motorcycles, and boats that use lead-acid batteries.

Is this answer helpful?

A

The RECOVERY function is used at the start of the charging process to help restore deeply discharged or sulfated batteries to a usable state.

Is this answer helpful?

A

Yes, it has electronic safeguards to prevent damage, but you should still follow vehicle manufacturer instructions regarding disconnection.

Is this answer helpful?

A

The green LED labeled 100% will light up to indicate that the charging process is complete.

Is this answer helpful?

A

Yes, in TRONIC or PULSE TRONIC mode, the charger can maintain the battery voltage automatically after the initial charge is done.

Is this answer helpful?

A

A flashing yellow LED indicates polarity reversal. You must immediately stop and swap the red and black clamp connections.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Supports multiple battery types including standard, AGM, and sealed batteries
  • Features intelligent IU charge curve for safe and efficient charging
  • Includes dedicated RECOVERY mode to revive sulfated batteries
  • Built-in protection against overload, short circuit, and polarity reversal
  • Clear LED indicators provide real-time charging status updates
VS

Disadvantages

  • Must be used in well-ventilated areas due to explosive gas risk
  • Requires manual selection of charging parameters by the user
  • Not suitable for non-rechargeable batteries
  • Cannot be operated safely inside a closed vehicle cabin
  • Maintenance requires skilled technicians if internal repairs are needed
M: QW-35-FL

Product Specification

Suitable for

AGM, Lead, EFB, Gel

Battery voltage

6V, 12V

Battery capacity

2-70Ah

Display

LED

Color

red, black

Dimensions

6.69x2.56x1.38in (WxHxD)

Weight

1.32lb

M: QW-35-FL

Product Description

Telwin T-Charge 12: The Ultimate Battery Charging Solution

The Telwin T-Charge 12 is a robust and versatile battery charger designed to meet the needs of automotive enthusiasts, mechanics, and everyday vehicle owners. Whether you are maintaining a standard petrol or diesel car, a motorcycle, or even a boat, this device offers reliable performance for both open and sealed lead-acid batteries. It features an intelligent IU charge curve that ensures optimal charging while protecting the battery from damage.

One of the standout features of the Telwin T-Charge 12 Manual is its user-friendly interface. The control panel allows you to easily select between different charging currents and voltages, including settings for 6V and 12V systems at 1A or 4A. The device also includes specialized modes such as AGM for Absorbent Glass Mat batteries and RECOVERY for reviving sulfated batteries. Visual feedback is provided through clear LED indicators that show the charging progress from 25% up to a full 100% charge, ensuring you always know the status of your battery.

Safety is paramount with the Telwin T-Charge 12. It is equipped with advanced internal electronic safeguards that protect against overloads, short circuits, and polarity reversals. The charger also warns users of potential hazards with distinct color-coded LEDs, such as a yellow light for polarity errors. This makes it safe for use in garages and workshops, provided standard safety precautions like avoiding sparks and ensuring ventilation are followed. The unit is built to handle various environments while keeping the connected electronics of modern vehicles secure.

Using the Telwin T-Charge 12 is straightforward. After connecting the clamps correctly to the battery terminals or chassis, simply plug the unit into a standard power outlet. The charger maintains a constant current and voltage during the process, automatically adjusting to keep the battery healthy. Once the green 100% LED lights up, the charging cycle is complete. For long-term maintenance, the device can be left connected in TRONIC or PULSE TRONIC mode to keep the battery topped up without overcharging.

Important Notes

  • Always disconnect the power supply before connecting or disconnecting clamps.
  • Ensure the battery electrolyte level covers the plates before charging.
  • Do not use the charger inside a vehicle or under the bonnet due to explosion risks.
  • Clean battery terminals to ensure good contact and prevent oxidation issues.
M: QW-35-FL

© Copyright 2026 Manual.ly