Manual.ly Logo

Telwin Superior 320 CE Manual

0.0 · 0 Ratings

PDF manual · 148 Pages

English

M: QW-35-FL
page

/ 148

Loading...
f779ff601105653506ccca47d18ebfab66fe page 5
- 5 -
INVERTERWELDINGMACHINESFORTIGANDMMAWELDINGDESIGNEDFOR
INDUSTRIALANDPROFESSIONALUSE.
Note:Inthefollowingtexttheterm“weldingmachine”willbeused.
1.GENERALSAFETYCONSIDERATIONSFORARCWELDING
The operator should be properly trained to use the welding machine safely
andshouldbeinformedabouttherisksrelatedtoarcweldingprocedures,the
associatedprotectionmeasuresandemergencyprocedures.
(Pleaserefertotheapplicablestandard“EN60974-9:Arcweldingequipment.
Part9:InstallationandUse).
- Avoiddirectcontactwiththeweldingcircuit:theno-loadvoltagesuppliedby
theweldingmachinecanbedangerousundercertaincircumstances.
- When the welding cables are being connected or checks and repairs are
carriedout the welding machine should be switched off and disconnected
fromthepowersupplyoutlet.
- Switch off the welding machine and disconnect it from the power supply
outletbeforereplacingconsumabletorchparts.
- Maketheelectricalconnectionsandinstallationaccordingtothesafetyrules
andlegislationinforce.
- Theweldingmachineshouldbeconnectedonlyandexclusivelytoapower
sourcewiththeneutralleadconnectedtoearth.
- Make sure that the power supply plug is correctly connected to the earth
protectionoutlet.
- Donotusetheweldingmachineindamporwetplacesanddonotweldinthe
rain.
- Donotusecableswithworninsulationorlooseconnections.
- Donotweldoncontainersorpipingthatcontainsorhascontainedammable
liquidorgaseousproducts.
- Donotoperateonmaterialscleanedwithchlorinatedsolventsornearsuch
substances.
- Donotweldoncontainersunderpressure.
- Removeallammablematerials(e.g.wood,paper,ragsetc.)fromtheworking
area.
- Provideadequateventilationorfacilitiesfortheremovalofweldingfumesnear
thearc;asystematicapproachisneededinevaluatingtheexposurelimitsfor
the welding fumes, which will depend on their composition, concentration
andthelengthofexposureitself.
- Keep the gas bottle (if used) away from heat sources, including direct
sunlight.
- Useelectricinsulationthatissuitableforthetorch,theworkpieceandany
metalpartsthatmaybeplacedonthegroundandnearby(accessible).
Thiscannormallybedonebywearinggloves,footwear,headprotectionand
clothingthataresuitableforthepurposeandbyusinginsulatingboardsor
mats.
- Alwaysprotectyoureyeswiththerelativelters,whichmustcomplywithUNI
EN169orUNIEN379,mountedonmasksorusehelmetsthatcomplywithUNI
EN175.
Use the relative re-resistant clothing (compliant with UNI EN 11611) and
weldinggloves(compliantwithUNIEN12477)withoutexposingtheskinto
the ultraviolet and infrared rays produced by the arc; the protection must
extend to other people who are near the arc by way of screens or non-
reectivesheets.
- Noise:Ifthedailypersonalnoiseexposure(LEPd)isequaltoorhigherthan85
dB(A)becauseofparticularlyintensiveweldingoperations,suitablepersonal
protectivemeansmustbeused(Tab.1).
- The ow of the welding current generates electromagnetic elds (EMF)
aroundtheweldingcircuit.
Electromagneticeldscaninterferewithcertainmedicalequipment(e.g.Pace-
makers,respiratoryequipment,metallicprosthesesetc.).
Adequateprotectivemeasuresmustbeadoptedforpersonswiththesetypesof
medicalapparatus.Forexample,theymustbeforbiddenaccesstotheareain
whichweldingmachinesareinoperation.
Thisweldingmachineconforms to technicalproductstandardsfor exclusive
useinanindustrialenvironmentforprofessionalpurposes.Itdoesnotassure
compliancewiththebasiclimitsrelativetohumanexposuretoelectromagnetic
eldsinthedomesticenvironment.
Theoperatormustadoptthefollowingproceduresinordertoreduceexposure
toelectromagneticelds:
- Fastenthetwoweldingcablesasclosetogetheraspossible.
- Keepheadandtrunkasfarawayaspossiblefromtheweldingcircuit.
- Neverwindweldingcablesaroundthebody.
- Avoidweldingwiththebodywithintheweldingcircuit.Keepbothcableson
thesamesideofthebody.
- Connecttheweldingcurrentreturncabletothepiecebeingwelded,asclose
aspossibletotheweldingjoint.
- Donotweldwhilecloseto,sittingonorleaningagainsttheweldingmachine
(keepatleast50cmawayfromit).
- Do not leave objects in ferromagnetic material in proximity of the welding
circuit.
- Minimumdistanced:20cm(Fig.O).
-ClassAequipment:
Thisweldingmachineconforms to technicalproductstandardsfor exclusive
use in an industrial environment and for professional purposes. It does not
assure compliance with electromagnetic compatibility in domestic dwellings
and in premises directly connected to a low-voltage power supply system
feedingbuildingsfordomesticuse.
EXTRA PRECAUTIONS
- WELDINGOPERATIONS:
- Inenvironmentswithincreasedriskofelectricshock.
- Inconnedspaces.
- Inthepresenceofammableorexplosivematerials.
MUSTBEevaluatedinadvancebyan“Expertsupervisor”andmustalwaysbe
carriedoutinthepresenceofotherpeopletrainedtointerveneinemergencies.
Allprotective technicalmeasures MUST be taken asprovided in7.10;A.8;
A.10oftheapplicablestandardEN60974-9:Arcweldingequipment.Part9:
InstallationandUse”.
-The operator MUST NOT BEALLOWED to weld in raised positions unless
safetyplatformsareused.
-VOLTAGE BETWEEN ELECTRODE HOLDERS OR TORCHES: working with
more than one welding machine on a single piece or on pieces that are
connected electrically may generate a dangerous accumulation of no-load
voltagebetweentwodifferentelectrodeholdersortorches,thevalueofwhich
mayreachdoubletheallowedlimit.
An expert coordinator must be designated to measuring the apparatus
to determine if any risks subsist and suitable protection measures can be
adopted,asforeseenbysection7.9oftheapplicablestandard“EN60974-9:
Arcweldingequipment.Part9:InstallationandUse”.
RESIDUAL RISKS
- OVERTURNING:positiontheweldingmachineonahorizontalsurfacethatis
abletosupporttheweight:otherwise(e.g.inclinedorunevenoorsetc.)there
isdangerofoverturning.
-IMPROPER USE: it is hazardous touse the welding machine for any work
otherthanthatforwhichitwasdesigned(e.g.de-icingmainswaterpipes).
- Donotusethehandletohangtheweldingmachine.
2.INTRODUCTIONANDGENERALDESCRIPTION
2.1INTRODUCTION
This welding machine is a power source for arc welding, made specically for TIG
(DC) (AC/DC) welding with HF or LIFT strike and MMA welding with coated electrodes
(rutile, acid, basic).
The particular features of this welding machine (INVERTER), such as high-speed and
ENGLISH
INDEX
1.GENERALSAFETYCONSIDERATIONSFORARCWELDING............................................... 5
2.INTRODUCTIONANDGENERALDESCRIPTION.................................................................... 5
2.1 INTRODUCTION .................................................................................................................. 5
2.2 OPTIONAL ACCESSORIES ................................................................................................. 6
3.TECHNICALDATA...................................................................................................................... 6
3.1 DATA PLATE (FIG. A) ........................................................................................................... 6
3.2 OTHER TECHNICAL DATA .................................................................................................. 6
4.DESCRIPTIONOFTHEWELDINGMACHINE......................................................................... 6
4.1 BLOCK DIAGRAM ................................................................................................................ 6
4.2 CONTROL, ADJUSTMENT AND CONNECTING DEVICES ................................................ 6
4.2.1 Rear panel (FIG. C) .................................................................................................... 6
4.2.2 Front panel FIG. D ...................................................................................................... 6
4.2.3 Front panel (FIG. D1) ................................................................................................. 7
4.3 G.R.A. water cooling unit ENABLING and DISABLING instructions (where applicable) ...... 8
5.INSTALLATION........................................................................................................................... 8
5.1 PREPARATION..................................................................................................................... 8
5.1.1 Assembling the return cable-clamp (FIG. E) ............................................................... 8
5.1.2 Assembling the welding cable-electrode holder clamp (FIG. E) ................................. 8
5.2 POSITION OF THE WELDING MACHINE ........................................................................... 8
5.3 CONNECTION TO THE MAIN POWER SUPPLY ................................................................ 8
5.3.1 Plug and outlet ............................................................................................................ 8
5.4 CONNECTION OF THE WELDING CABLES ...................................................................... 8
5.4.1 TIG welding................................................................................................................. 8
5.4.2 MMA WELDING .......................................................................................................... 8
6.WELDING:DESCRIPTIONOFTHEPROCEDURE................................................................... 8
6.1 TIG WELDING ...................................................................................................................... 8
6.1.1 HF and LIFT strike ...................................................................................................... 8
6.1.2 TIG DC welding .......................................................................................................... 9
6.1.3 TIG AC welding .......................................................................................................... 9
6.1.4 Procedure ................................................................................................................... 9
6.2 MMA WELDING .................................................................................................................... 9
6.2.1 Procedure ................................................................................................................... 9
7.MAINTENANCE.......................................................................................................................... 9
7.1 ROUTINE MAINTENANCE .................................................................................................. 9
7.1.1 Torch ........................................................................................................................... 9
7.2 EXTRAORDINARY MAINTENANCE .................................................................................... 9
8.TROUBLESHOOTING................................................................................................................ 9
page page

Chat with your Telwin Superior 320 CE manual using AI

Get instant AI answers from your Telwin Superior 320 CE manual

Ask anything about the Telwin Superior 320 CE. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Superior 320 CE?

Yes No

Frequently Asked Questions

A

No, this machine is classified as Class A equipment intended exclusively for industrial and professional environments. It does not ensure compliance with electromagnetic compatibility limits required for domestic dwellings.

Is this answer helpful?

A

No, the welding current generates electromagnetic fields that can interfere with medical equipment such as pacemakers. Individuals with such devices or metal prostheses are prohibited from using or being near the operating machine.

Is this answer helpful?

A

It handles low and high-carbon steels, stainless steel, copper, nickel, titanium, aluminum, and magnesium. TIG AC mode is specifically effective for aluminum and magnesium due to its oxide-cleaning capability.

Is this answer helpful?

A

Use the mode selection push-buttons on the front panel. You can select TIG HF, TIG LIFT, or MMA modes depending on your specific welding requirements and electrode type.

Is this answer helpful?

A

Hot Start provides a dynamic overcurrent during the initial phase of MMA welding. This improves arc fluidity and helps prevent the electrode from sticking to the workpiece when starting the weld.

Is this answer helpful?

A

A water cooling unit is optional but recommended for high-duty cycle operations. The machine has a connector for a G.R.A. water cooling unit which can be enabled via the control panel settings.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Advanced inverter technology ensures compact size and lightweight portability
  • Versatile TIG and MMA capabilities with HF and Lift arc striking options
  • Microprocessor control allows precise adjustment of welding parameters
  • Hot Start and Arc Force features improve MMA welding stability and fluidity
  • Comprehensive safety alarms and thermal protection systems included
VS

Disadvantages

  • Designed strictly for industrial use and not compliant for domestic environments
  • Electromagnetic fields may interfere with medical devices like pacemakers
  • Requires qualified personnel for installation and electrical connections
  • Complex parameter settings may have a steep learning curve for beginners
  • Must be operated by authorized personnel only to maintain warranty and safety
M: QW-35-FL

Product Specification

Power

7kW (230V), 9kW (400V)

Open-circuit voltage

60/63V

Control range

10-250A (MMA/TIG) at 230V, 10-270A (MMA/TIG) at 400V

Electrodes

1.6-6mm (MMA)

Protection class

IP23

Dimensions

14.17x18.11x7.48in (HxDxW)

Weight

22.49lbs

M: QW-35-FL

Product Description

Telwin Superior 320 CE: Professional Inverter Welding Excellence

The Telwin Superior 320 CE MMA/WIG Inverter Welding Machine represents a pinnacle of modern industrial welding technology. Designed specifically for professional and industrial environments, this robust unit combines the versatility of MMA (Manual Metal Arc) welding with advanced TIG (Tungsten Inert Gas) capabilities. Whether you are working with low-carbon steels, stainless steel, aluminum, or magnesium alloys, this inverter system delivers precise control and exceptional weld quality.

At the heart of the machine lies its sophisticated inverter technology. By converting power supply voltage to high-frequency alternating current, the unit achieves drastic reductions in size and weight without sacrificing performance. This makes the Telwin Superior 320 CE remarkably easy to handle and transport on busy job sites. The microprocessor-controlled system allows for extensive parameter adjustments, ensuring perfect welding conditions for any material or thickness.

For TIG applications, the machine supports both High Frequency (HF) and Lift arc striking methods. HF strike offers non-contact ignition ideal for all positions, while Lift strike minimizes tungsten contamination and electrical interference. Users can choose between DC and AC modes, with AC functionality enabling the cleaning of oxide layers on aluminum through ionic sandblasting. The adjustable balance parameter gives operators fine-tuned control over penetration and surface cleaning.

In MMA mode, the machine features intelligent Hot Start and Arc Force functions. These dynamic overcurrent settings improve arc fluidity and prevent electrode sticking, resulting in smoother starts and more stable arcs even with difficult electrodes. The front panel provides an intuitive interface with an alphanumeric display, allowing users to easily adjust pre-gas, post-gas, initial slope, main current, and end slope parameters.

Safety is paramount in the design of this equipment. The machine includes comprehensive thermal protection, voltage reduction devices (VRD), and alarm signaling systems. It conforms to strict European safety standards for industrial use. However, it is designed exclusively for professional environments and may not be suitable for domestic dwellings due to electromagnetic field emissions. Operators must adhere to strict safety protocols regarding protective gear, ventilation, and electrical connections.

Key Notes for Operators

  • Always read the instruction manual before first use.
  • Ensure proper grounding and ventilation to avoid fume inhalation.
  • Do not use the handle for hanging the machine to prevent structural damage.
  • Persons with pacemakers or metal prostheses should not operate this machine due to electromagnetic fields.
M: QW-35-FL

© Copyright 2026 Manual.ly