Manual.ly Logo

Telwin Maxima 190 Synergic Manual

0.0 · 0 Ratings

PDF manual · 156 Pages

English

M: QW-35-FL
page

/ 156

Loading...
e7510bc10cbb0b93feb6083c682e161c7914 page 5
- 5 -
(EN)
INSTRUCTION MANUAL
WARNING:
BEFORE USING THE WELDING MACHINE READ THE INSTRUCTION
MANUAL CAREFULLY.
CONTINUOUS WIRE WELDING MACHINE FOR MIG-MAG ARC AND FLUX,
TIG, MMA WELDING FOR PROFESSIONAL AND INDUSTRIAL USE.
NB: The following text uses the term "Welding machine" and "Multiprocess
Welding Machine" for models prepared for MIG-MAG AND FLUX, TIG,
MMA welding.
1. GENERAL SAFETY CONSIDERATIONS FOR ARC WELDING
The operator should be properly trained to use the welding machine
safely and should be informed about the risks related to arc welding
procedures, the associated protection measures and emergency
procedures.
(Please refer to the applicable standard ”EN 60974-9: Arc welding
equipment. Part 9: Installation and Use).
- Avoid direct contact with the welding circuit: the no-load voltage
supplied by the welding machine can be dangerous under certain
circumstances.
- When the welding cables are being connected or checks and
repairs are carried out the welding machine should be switched o
and disconnected from the power supply outlet.
- Switch o the welding machine and disconnect it from the power
supply outlet before replacing consumable torch parts.
- Make the electrical connections and installation according to the
safety rules and legislation in force.
- The welding machine should be connected only and exclusively to
a power source with the neutral lead connected to earth.
- Make sure that the power supply plug is correctly connected to the
earth protection outlet.
- Do not use the welding machine in damp or wet places and do not
weld in the rain.
- Do not use cables with worn insulation or loose connections.
- Do not weld on containers or piping that contains or has contained
ammable liquid or gaseous products.
- Do not operate on materials cleaned with chlorinated solvents or
near such substances.
- Do not weld on containers under pressure.
- Remove all ammable materials (e.g. wood, paper, rags etc.) from
the working area.
- Provide adequate ventilation or facilities for the removal of
welding fumes near the arc; a systematic approach is needed in
evaluating the exposure limits for the welding fumes, which will
depend on their composition, concentration and the length of
exposure itself.
- Keep the gas bottle (if used) away from heat sources, including
direct sunlight.
- Use electric insulation that is suitable for the torch, the workpiece
and any metal parts that may be placed on the ground and nearby
(accessible).
This can normally be done by wearing gloves, footwear, head
protection and clothing that are suitable for the purpose and by
using insulating boards or mats.
- Always protect your eyes with the relative lters, which must
comply with UNI EN 169 or UNI EN 379, mounted on masks or use
helmets that comply with UNI EN 175.
Use the relative re-resistant clothing (compliant with UNI EN
11611) and welding gloves (compliant with UNI EN 12477) without
exposing the skin to the ultraviolet and infrared rays produced by
the arc; the protection must extend to other people who are near
the arc by way of screens or non-reective sheets.
- Noise: If the daily personal noise exposure (LEPd) is equal to or higher
than 85 dB(A) because of particularly intensive welding operations,
suitable personal protective means must be used (Tab. 1).
- The ow of the welding current generates electromagnetic elds
(EMF) around the welding circuit.
Electromagnetic elds can interfere with certain medical equipment
(e.g. Pace-makers, respiratory equipment, metallic prostheses etc.).
Adequate protective measures must be adopted for persons
with these types of medical apparatus. For example, they must
be forbidden access to the area in which welding machines are in
operation.
This welding machine conforms to technical product standards for
exclusive use in an industrial environment for professional purposes.
It does not assure compliance with the basic limits relative to human
exposure to electromagnetic elds in the domestic environment.
The operator must adopt the following procedures in order to reduce
exposure to electromagnetic elds:
- Fasten the two welding cables as close together as possible.
- Keep head and trunk as far away as possible from the welding
circuit.
- Never wind welding cables around the body.
- Avoid welding with the body within the welding circuit. Keep both
cables on the same side of the body.
- Connect the welding current return cable to the piece being
welded, as close as possible to the welding joint.
- Do not weld while close to, sitting on or leaning against the
welding machine (keep at least 50 cm away from it).
- Do not leave objects in ferromagnetic material in proximity of the
welding circuit.
- Minimum distance d= 20 cm (Fig. G).
- Class A equipment:
This welding machine conforms to technical product standards
for exclusive use in an industrial environment and for professional
purposes. It does not assure compliance with electromagnetic
compatibility in domestic dwellings and in premises directly
connected to a low-voltage power supply system feeding buildings
for domestic use.
EXTRA PRECAUTIONS
- WELDING OPERATIONS:
- In environments with increased riskof electric shock;
- In conned spaces;
- In the presence of ammable or explosive materials;
MUST BE evaluated in advance by an “Expert supervisor” and
must always be carried out in the presence of other people
trained to intervene in emergencies.
All protective technical measures MUST be taken as provided
in 7.10; A.8; A.10 of the applicable standard EN 60974-9: Arc
welding equipment. Part 9: Installation and Use”.
- Welding MUST NOT be allowed if the welding machine or wire
feeder is supported by the operator (e.g. using belts).
- The operator MUST NOT BE ALLOWED to weld in raised positions
unless safety platforms are used.
- VOLTAGE BETWEEN ELECTRODE HOLDERS OR TORCHES: working
with more than one welding machine on a single piece or on
pieces that are connected electrically may generate a dangerous
accumulation of no-load voltage between two dierent electrode
holders or torches, the value of which may reach double the
allowed limit.
An expert coordinator must be designated to measuring the
apparatus to determine if any risks subsist and suitable protection
measures can be adopted, as foreseen by section 7.9 of the
applicable standard ”EN 60974-9: Arc welding equipment. Part 9:
Installation and Use”.
RESIDUAL RISKS
- OVERTURNING: position the welding machine on a horizontal
surface that is able to support the weight: otherwise (e.g. inclined
or uneven oors etc.) there is danger of overturning.

Chat with your Telwin Maxima 190 Synergic manual using AI

Get instant AI answers from your Telwin Maxima 190 Synergic manual

Ask anything about the Telwin Maxima 190 Synergic. Answers come from this manual, with the pages they are based on.

Maxima 190 Synergic Maintenance Schedule

Before every use
Check torch nozzle, contact tip and gas diffuser

Verify wear state and correct assembly of the end parts of the torch: nozzle, contact tip, and gas diffuser.

Show in the manual (page 10)
Every time wire reel is changed
Blow out wire-guide hose with dry compressed air

Use dry compressed air (max 5 bar) to clean the wire-guide hose and ensure it is not damaged.

Show in the manual (page 10)
Frequently
Check wire feeder rollers for wear

Make frequent checks on the state of wear of the wire feeder rollers.

Show in the manual (page 10)
Regularly
Remove metal dust from wire feeder area

Regularly remove metal dust deposited in the feeder area, including rollers and wire-guide infeed/outfeed.

Show in the manual (page 10)
Periodically
Inspect gas pipe and connector seals

Make regular checks on the tightness of the gas pipe and connector seals.

Show in the manual (page 10)
Periodically
Clean internal components with dry compressed air

Remove dust from transformer, reactance and rectifier using a jet of dry compressed air (max 10 bar). Frequency depends on use and environment dustiness.

Show in the manual (page 10)
Periodically
Check electrical connections and wiring insulation

Ensure electrical connections are tight and check wiring for damage to the insulation during internal inspections.

Show in the manual (page 10)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Maxima 190 Synergic?

Yes No

Frequently Asked Questions

A

No, this equipment is Class A and intended for exclusive industrial use. It does not meet electromagnetic compatibility limits for domestic dwellings.

Is this answer helpful?

A

You must wear a self-darkening helmet with filters, fire-resistant clothing, protective gloves, and eye protection to guard against UV radiation and sparks.

Is this answer helpful?

A

Yes, it is suitable for welding aluminum using Argon gas and specific electrode wires designed for non-ferrous metals.

Is this answer helpful?

A

Connect the return cable to the workpiece or metal bench as close as possible to the welding joint to ensure a stable arc.

Is this answer helpful?

A

The thermal safeguard will trigger, putting the machine in standby mode until the internal temperature returns to safe limits.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Synergic automatic parameter setting for fast and easy welding setup
  • Multiprocess capability supporting MIG-MAG, Flux, TIG, and MMA welding
  • Built-in thermal protection prevents overheating during extended use
  • Compact inverter design suitable for mobile professional applications
VS

Disadvantages

  • Not recommended for domestic environments due to electromagnetic field emissions
  • Requires qualified technicians for electrical installation and repairs
  • TIG and MMA modes are only available on the multiprocess version
  • Strict safety protocols needed for users with medical implants or prostheses
M: QW-35-FL

Product Specification

Power

3.2kW (230V)

Open-circuit voltage

44V

Control range

20-170A (MIG/MAG/FLUX)

Protection class

IP23

Dimensions

14.6x17.7x9.3in (HxDxW)

Weight

21.85lbs

M: QW-35-FL

Product Description

Telwin Maxima 190 Synergic MIG/MAG/FLUX Inverter Welding Machine Review

The Telwin Maxima 190 Synergic is a versatile inverter welding machine designed for professional and industrial applications. It excels in MIG-MAG, Flux, TIG, and MMA welding processes, making it an ideal choice for light metalwork fabrication, body shops, and general repair work. The synergic operation feature simplifies the setup process by automatically adjusting parameters based on material thickness, ensuring high arc control and consistent weld quality.

This multiprocess unit supports various materials including carbon steel, stainless steel, aluminum, and copper alloys. Users can switch between gas-shielded welding with CO2 or Argon mixes and flux-cored welding without gas. The TIG mode offers lift arc starting for precision work on heavy metals like titanium and nickel. Safety is paramount, with built-in protections against short circuits, overvoltage, and thermal overload. The machine requires strict adherence to safety protocols regarding electromagnetic fields and proper grounding.

Installation involves connecting to a single-phase power supply with a neutral earth connection. Operators must ensure adequate ventilation to remove hazardous fumes and wear appropriate protective gear such as helmets, gloves, and fire-resistant clothing. The device includes a digital control panel for easy adjustment of wire speed, arc length, and current settings. Regular maintenance, such as cleaning rollers and checking cable connections, ensures longevity and optimal performance.

M: QW-35-FL

© Copyright 2026 Manual.ly