- Open the reel compartment door.This process allows dented or deformed metal sheets to be re-shaped, without having
- Position the wire reel on the spindle, holding the end of the wire upwards; make sure to hammer out the sheets from behind. This is particularly useful for sections of
the tab for pulling the spindle is correctly seated in its hole (1a).
bodywork with inaccessible rear sides.
- Release the pressure counter-roller/s and move it/them away from the lower roller/s
The operation is carried out as follows:
-Replace the nozzle of the torch with the nozzle required for riveting. This nozzle has a
(2a).
side hole for housing the rivet.
-Make sure the puller roller is suitable for the wire being used (2b).
-Turn the current adjustment switch to position 3.
- Free the end of the wire and remove the distorted end with a clean cut and no burr;
-Adjust the feed speed according to the current and the diameter of the wire used as if a
turn the reel anti-clockwise and thread the end of the wire into the wire-guide infeed,
welding operation was to be carried out.
pushing it 50-100mm into the wire guide of the torch fitting (2c).
-Turn the switch to <TIMER> position.
- Re-position the counter-roller/s, adjusting the pressure to an intermediate value, and
-Set the time at 1-1.5 seconds
make sure that the wire is correctly positioned in the groove of the lower roller (3).
A spot of welding will therefore be carried out at the point where the head of the rivet is
- Use the adjustment screw located at the centre of the spindle to apply a slight braking
located and so joining the latter to the metal sheet. The dented metal sheet can now be
pressure on the spindle itself (1b).
re-shaped using the appropriate appliance
- Remove the nozzle and contact tip (4a).
6.6 MET
AL SHEET HARDENING (FIG.M)
-Insert the welding machine plug in the power supply outlet, switch on the welding
This operation is only possible for compact welding machines with one or more earth
machine, press the torch button and wait for the end of the wire to pass through the
connectors.
whole of the wire guide hose and protrude by 10-15 cm from the front part of the
In order to carry out this process, the kit should be requested.
torch, release the button.
After welding and hammering, the metal sheet looses its original characteristics; body
No, this machine is designed exclusively for industrial and professional use. It does not comply with electromagnetic compatibility standards required for domestic environments.
Is this answer helpful?
A
It handles carbon steel, low-alloy steel, stainless steel, and aluminum when used with the appropriate shielding gases and filler wires.
Is this answer helpful?
A
Yes, the machine features an adjustable timer that allows for precise spot welding and rivet welding operations.
Is this answer helpful?
A
Operators must wear protective clothing, gloves, eye protection with actinic glass, and hearing protection if noise levels exceed 85dB(A).
Is this answer helpful?
A
Regularly remove metal dust deposits from the rollers and guide hose using dry compressed air to ensure smooth wire feeding.
Is this answer helpful?
A
Some versions include a water-cooling unit (R.A. version) which must be filled only when the machine is switched off and disconnected.
Is this answer helpful?
M: QW-35-FL
Advantagesand
Disadvantages
Advantages
Versatile capability for MIG, MAG, Flux, Spot, and Rivet welding on multiple materials
Four-roller wire feeder system ensures stable feeding for various wire diameters
Dual timer function allows for precise control during spot welding operations
Robust industrial design built for continuous professional use in harsh environments
Comprehensive safety features including thermal overload protection
VS
Disadvantages
Not certified for use in domestic residential environments due to EMF levels
Requires three-phase power supply which may limit portability without generators
Complex setup procedures require trained personnel for safe installation
Routine maintenance involves frequent cleaning of rollers and guides to prevent jams
Aluminum welding requires specific optional kits like Teflon hoses and special tips
M: QW-35-FL
Product
Specification
Power
11.5kW (230V/400V)
Open circuit voltage
41.5V
Control range
40-300A (MIG/MAG/FLUX)
Protection class
IP22
Dimensions
32.7x37.2x22.2in (HxDxW)
Weight
211.64lbs
M: QW-35-FL
Product
Description
Telwin Mastermig 300 MIG/MAG/FLUX Shielded Gas Welding Machine Manual
The Telwin Mastermig 300 represents a pinnacle of professional welding technology, designed specifically for demanding industrial and commercial environments. This versatile unit is a continuous wire welding machine capable of performing MIG, MAG, and Flux shielded gas arc welding operations. It serves as a robust power source ideal for carbon steel, low-alloy steel, stainless steel, and aluminum applications. Whether you are working with solid wires using CO2 or Argon-CO mixtures, or utilizing cored tubular electrodes for flux-cored welding, this machine delivers consistent performance.
Engineered for flexibility, the Telwin Mastermig 300 supports various configurations including compact models and setups with removable wire feeders. The system features a four-roller drive mechanism that ensures smooth wire feeding across different material types. Operators can easily adjust voltage and current settings to match specific welding requirements, ensuring optimal arc stability and high-quality weld beads. The inclusion of advanced features like a dual timer allows for precise spot welding and rivet welding tasks, making it suitable for complex fabrication jobs where access to the rear side of a joint is limited.
Safety is paramount in the design of this equipment. The manual emphasizes strict adherence to general safety considerations, including the prevention of electric shock, fire hazards, and exposure to harmful ultraviolet radiation. Users must wear appropriate protective clothing, gloves, and eye protection at all times. The machine is built to Class A standards, meaning it is intended for exclusive use in industrial settings and may not be fully compliant with electromagnetic compatibility limits for domestic dwellings. Proper installation requires connection to a three-phase power supply with a neutral conductor grounded to earth, adhering to EN 61000-3-11 flicker standards.
Maintenance routines are straightforward yet critical for longevity. Routine checks involve inspecting the torch for worn parts, cleaning the wire feeder rollers of metal dust, and ensuring gas lines are free from leaks. Extraordinary maintenance should only be performed by qualified technicians after disconnecting the power supply. The unit includes thermal safeguards that trigger if operating limits are exceeded, automatically placing the machine in standby until it cools down. With its durable construction and comprehensive accessory options, the Telwin Mastermig 300 stands as a reliable partner for professional welders seeking efficiency and precision.