Manual.ly Logo

Telwin Infinity TIG 225 DC Manual

0.0 · 0 Ratings

PDF manual · 136 Pages

English

M: QW-35-FL
page

/ 136

Loading...
3df68ae83bf9c68047d6896336560e72e691 page 5
- 5 -
INVERTERWELDINGMACHINESFORTIGANDMMAWELDINGDESIGNEDFOR
INDUSTRIALANDPROFESSIONALUSE.
Note:Inthefollowingtexttheterm“weldingmachine”willbeused.
1.GENERALSAFETYCONSIDERATIONSFORARCWELDING
The operator should be properly trained to use the welding machine safely
andshouldbeinformedabouttherisksrelatedtoarcweldingprocedures,the
associatedprotectionmeasuresandemergencyprocedures.
(Pleaserefertotheapplicablestandard“EN60974-9:Arcweldingequipment.
Part9:InstallationandUse).
- Avoiddirectcontactwiththeweldingcircuit:theno-loadvoltagesuppliedby
theweldingmachinecanbedangerousundercertaincircumstances.
- When the welding cables are being connected or checks and repairs are
carriedout the welding machine should be switched off and disconnected
fromthepowersupplyoutlet.
- Switch off the welding machine and disconnect it from the power supply
outletbeforereplacingconsumabletorchparts.
- Maketheelectricalconnectionsandinstallationaccordingtothesafetyrules
andlegislationinforce.
- Theweldingmachineshouldbeconnectedonlyandexclusivelytoapower
sourcewiththeneutralleadconnectedtoearth.
- Make sure that the power supply plug is correctly connected to the earth
protectionoutlet.
- Donotusetheweldingmachineindamporwetplacesanddonotweldinthe
rain.
- Donotusecableswithworninsulationorlooseconnections.
- Donotweldoncontainersorpipingthatcontainsorhascontainedammable
liquidorgaseousproducts.
- Donotoperateonmaterialscleanedwithchlorinatedsolventsornearsuch
substances.
- Donotweldoncontainersunderpressure.
- Removeallammablematerials(e.g.wood,paper,ragsetc.)fromtheworking
area.
- Provideadequateventilationorfacilitiesfortheremovalofweldingfumesnear
thearc;asystematicapproachisneededinevaluatingtheexposurelimitsfor
the welding fumes, which will depend on their composition, concentration
andthelengthofexposureitself.
- Keep the gas bottle (if used) away from heat sources, including direct
sunlight.
- Useelectricinsulationthatissuitableforthetorch,theworkpieceandany
metalpartsthatmaybeplacedonthegroundandnearby(accessible).
Thiscannormallybedonebywearinggloves,footwear,headprotectionand
clothingthataresuitableforthepurposeandbyusinginsulatingboardsor
mats.
- Alwaysprotectyoureyeswiththerelativelters,whichmustcomplywithUNI
EN169orUNIEN379,mountedonmasksorusehelmetsthatcomplywithUNI
EN175.
Use the relative re-resistant clothing (compliant with UNI EN 11611) and
weldinggloves(compliantwithUNIEN12477)withoutexposingtheskinto
the ultraviolet and infrared rays produced by the arc; the protection must
extend to other people who are near the arc by way of screens or non-
reectivesheets.
- Noise:Ifthedailypersonalnoiseexposure(LEPd)isequaltoorhigherthan85
dB(A)becauseofparticularlyintensiveweldingoperations,suitablepersonal
protectivemeansmustbeused(Tab.1).
- The ow of the welding current generates electromagnetic elds (EMF)
aroundtheweldingcircuit.
Electromagneticeldscaninterferewithcertainmedicalequipment(e.g.Pace-
makers,respiratoryequipment,metallicprosthesesetc.).
Adequateprotectivemeasuresmustbeadoptedforpersonswiththesetypesof
medicalapparatus.Forexample,theymustbeforbiddenaccesstotheareain
whichweldingmachinesareinoperation.
Thisweldingmachineconforms to technicalproductstandardsfor exclusive
useinanindustrialenvironmentforprofessionalpurposes.Itdoesnotassure
compliancewiththebasiclimitsrelativetohumanexposuretoelectromagnetic
eldsinthedomesticenvironment.
Theoperatormustadoptthefollowingproceduresinordertoreduceexposure
toelectromagneticelds:
- Fastenthetwoweldingcablesasclosetogetheraspossible.
- Keepheadandtrunkasfarawayaspossiblefromtheweldingcircuit.
- Neverwindweldingcablesaroundthebody.
- Avoidweldingwiththebodywithintheweldingcircuit.Keepbothcableson
thesamesideofthebody.
- Connecttheweldingcurrentreturncabletothepiecebeingwelded,asclose
aspossibletotheweldingjoint.
- Donotweldwhilecloseto,sittingonorleaningagainsttheweldingmachine
(keepatleast50cmawayfromit).
- Do not leave objects in ferromagnetic material in proximity of the welding
circuit.
- Minimumdistanced:20cm(Fig.O).
-ClassAequipment:
Thisweldingmachineconforms to technicalproductstandardsfor exclusive
use in an industrial environment and for professional purposes. It does not
assure compliance with electromagnetic compatibility in domestic dwellings
and in premises directly connected to a low-voltage power supply system
feedingbuildingsfordomesticuse.
EXTRA PRECAUTIONS
- WELDINGOPERATIONS:
- Inenvironmentswithincreasedriskofelectricshock.
- Inconnedspaces.
- Inthepresenceofammableorexplosivematerials.
MUSTBEevaluatedinadvancebyan“Expertsupervisor”andmustalwaysbe
carriedoutinthepresenceofotherpeopletrainedtointerveneinemergencies.
Allprotective technicalmeasures MUST be taken asprovided in7.10;A.8;
A.10oftheapplicablestandardEN60974-9:Arcweldingequipment.Part9:
InstallationandUse”.
-The operator MUST NOT BEALLOWED to weld in raised positions unless
safetyplatformsareused.
-VOLTAGE BETWEEN ELECTRODE HOLDERS OR TORCHES: working with
more than one welding machine on a single piece or on pieces that are
connected electrically may generate a dangerous accumulation of no-load
voltagebetweentwodifferentelectrodeholdersortorches,thevalueofwhich
mayreachdoubletheallowedlimit.
An expert coordinator must be designated to measuring the apparatus
to determine if any risks subsist and suitable protection measures can be
adopted,asforeseenbysection7.9oftheapplicablestandard“EN60974-9:
Arcweldingequipment.Part9:InstallationandUse”.
RESIDUAL RISKS
- OVERTURNING:positiontheweldingmachineonahorizontalsurfacethatis
abletosupporttheweight:otherwise(e.g.inclinedorunevenoorsetc.)there
isdangerofoverturning.
-IMPROPER USE: it is hazardous touse the welding machine for any work
otherthanthatforwhichitwasdesigned(e.g.de-icingmainswaterpipes).
- Donotusethehandletohangtheweldingmachine.
2.INTRODUCTIONANDGENERALDESCRIPTION
2.1INTRODUCTION
This welding machine is a power source for arc welding, made specically for TIG
(DC) (AC/DC) welding with HF or LIFT strike and MMA welding with coated electrodes
ENGLISH
INDEX
1.GENERALSAFETYCONSIDERATIONSFORARCWELDING..........................5
2.INTRODUCTIONANDGENERALDESCRIPTION...............................................5
2.1 INTRODUCTION ..............................................................................................5
2.2 ACCESSORIES ON REQUEST (if not planned) ..............................................6
3.TECHNICALDATA................................................................................................6
3.1 DATA PLATE (FIG. A) .......................................................................................6
3.2 OTHER TECHNICAL DATA ..............................................................................6
4.DESCRIPTIONOFTHEWELDINGMACHINE....................................................6
4.1 BLOCK DIAGRAM ...........................................................................................6
4.2 CONTROL, ADJUSTMENT AND CONNECTING DEVICES............................6
4.2.1 Rear panel (FIG. C) .................................................................................6
4.2.2 Front panel FIG. D...................................................................................6
5.INSTALLATION......................................................................................................7
5.1 PREPARATION (FIG. P) ..................................................................................7
5.1.1 Assembling the return cable-clamp (FIG. E) ...........................................7
5.1.2 Assembling the welding cable-electrode holder clamp (FIG. E) ..............7
5.2 POSITION OF THE WELDING MACHINE .......................................................7
5.3 CONNECTION TO THE MAIN POWER SUPPLY ............................................7
5.3.1 Plug and outlet ........................................................................................7
5.4 CONNECTION OF THE WELDING CABLES ..................................................7
5.4.1 TIG welding .............................................................................................7
5.4.2 MMA WELDING ......................................................................................7
6.WELDING:DESCRIPTIONOFTHEPROCEDURE..............................................7
6.1 TIG WELDING ..................................................................................................7
6.1.1 HF and LIFT strike ...................................................................................8
6.1.2 TIG DC welding .......................................................................................8
6.1.3 TIG AC welding (if installed) ....................................................................8
6.1.4 Procedure ................................................................................................8
6.2 MMA WELDING ...............................................................................................8
6.2.1 Procedure ................................................................................................8
7.MAINTENANCE.....................................................................................................8
7.1 ROUTINE MAINTENANCE ..............................................................................8
7.1.1 Torch ........................................................................................................8
7.2 EXTRAORDINARY MAINTENANCE ...............................................................8
8.TROUBLESHOOTING...........................................................................................8
page page

Chat with your Telwin Infinity TIG 225 DC manual using AI

Get instant AI answers from your Telwin Infinity TIG 225 DC manual

Ask anything about the Telwin Infinity TIG 225 DC. Answers come from this manual, with the pages they are based on.

Infinity TIG 225 DC Maintenance Schedule

Daily
Check torch terminal parts for wear and assembly

At least once a day check the nozzle, electrode, electrode-holder clamp, and gas diffuser for wear and ensure they are assembled correctly.

Regularly
Inspect gas pipe and connector seals

Make regular checks on the gas pipe and connector seals to ensure integrity.

Periodically
Clean dust from internal electronic boards

Inspect inside of machine and remove dust from electronic boards with a soft brush or appropriate solvents, frequency depends on usage and dust conditions.

Periodically
Check electrical connections and wiring insulation

Ensure electrical connections are tight and check wiring for damage to insulation during internal inspection.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Infinity TIG 225 DC?

Yes No

Frequently Asked Questions

A

No, this machine is designed exclusively for industrial and professional use. It does not assure compliance with electromagnetic compatibility limits for domestic dwellings.

Is this answer helpful?

A

Operators must wear protective clothing, gloves, eye protection with appropriate filters, and hearing protection if noise levels exceed 85 dB(A).

Is this answer helpful?

A

Screw the pressure reducing valve to the bottle, connect the gas hose to the valve and the machine, then adjust the flow rate according to the recommended tables.

Is this answer helpful?

A

The thermal safeguard will trigger, putting the machine in standby mode until the internal temperature returns to safe operating limits.

Is this answer helpful?

A

Yes, it supports remote controls with one or two potentiometers as well as foot pedals for adjusting current during operation.

Is this answer helpful?

A

No, users with vital electrical or electronic apparatus like pacemakers or metal prostheses are strictly prohibited from using this equipment.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Advanced inverter technology ensures high-quality welds with precise control.
  • Compact and lightweight design makes it highly portable for professional use.
  • Microprocessor control allows for complex parameter settings and automation.
  • Comprehensive safety features protect against thermal and electrical hazards.
VS

Disadvantages

  • Requires qualified personnel for installation and electrical connections.
  • Not suitable for domestic environments due to electromagnetic field emissions.
  • Complex interface may require a learning curve for new operators.
M: QW-35-FL

Product Specification

Power

4.7kW (230V)

Open-circuit voltage

82V

Regulating range

10-200A (MMA/WIG)

Electrodes

1/16-5/32in (MMA)

Protection class

IP23

Dimensions

11.4x15.4x6.1in (HxWxD)

Weight

13.23lb

M: QW-35-FL

Product Description

Telwin Infinity TIG 225 DC MMA/WIG Inverter Welding Machine Review

The Telwin Infinity TIG 225 DC MMA/WIG Inverter Welding Machine represents a significant leap in professional welding technology. Designed specifically for industrial and professional environments, this unit combines the versatility of TIG and MMA processes into a compact, lightweight package. The core of its performance lies in advanced inverter technology, which allows for high-speed and precise current adjustments. This results in superior weld quality with minimal spatter and excellent arc stability across various materials.

One of the standout features of this machine is its microprocessor control system. This intelligent brain manages complex welding cycles, ensuring perfect operation regardless of the material being used or the environmental conditions. Whether you are performing TIG welding with high-frequency or lift start methods, or engaging in standard MMA stick welding with coated electrodes, the Infinity TIG 225 adapts seamlessly. The inverter design drastically reduces the size and weight of the transformer components, making the unit incredibly easy to handle and transport around busy job sites.

Safety is paramount in the design of this equipment. The manual emphasizes strict adherence to safety protocols regarding electromagnetic fields, electric shock prevention, and fire hazards. It includes robust protection systems against thermal overload, overvoltage, and undervoltage conditions. The machine is built to withstand demanding industrial use while maintaining compliance with European safety standards. Operators can rely on its durability and reliability for long-term productivity without compromising on worker safety.

Key Features

  • Microprocessor-controlled precision for all welding types.
  • Compact and lightweight design for easy mobility.
  • Comprehensive safety protections including thermal and electrical safeguards.
  • Versatile connectivity for remote controls and pedals.

Notes

Always ensure the machine is disconnected from power before performing any maintenance. Regular cleaning of internal dust is essential to prevent overheating.

M: QW-35-FL

© Copyright 2026 Manual.ly