Manual.ly Logo

Telwin Defender 8 Manual

0.0 · 0 Ratings

PDF manual · 104 Pages

English

M: QW-35-FL
page

/ 104

Loading...
eee0beaa1ccf8f60a0a487a52c6096702529 page 6
- 6 -
5. OPERATION
BEFORE CHARGING
NB: Before charging check that the capacity of the battery
(Ah) which is to be charged, is not inferior to that reported
on the data table. (C min).
Follow the instructions, taking great care to respect the
order given below.
- Remove the caps of the battery charger (if foreseen) so as to
let the gas produced go out.
- Check that the level of the electrolyte covers the plates of
the battery. If these were not covered add distilled water
and cover them up to 5-10 mm.
WARNING: USE THE MAXIMUM CAUTION
DURING THIS OPERATION AS THE
ELECTROLYTE IS A HIGHLY CORROSIVE ACID.
- Make sure the battery charger is disconnected from the
power supply.
- Check the polarities of the battery terminals: positive for
the + symbol and negative for the - symbol.
NOTE: if the symbols are indistinguishable remember
that the positive terminal is the one not connected to the
vehicle chassis.
- Connect the red charge clamp to the positive terminal of
the battery ( + symbol).
- Connect the black charge clamp to the vehicle chassis, at a
safe distance from the battery and the fuel pipe.
NOTE: if the battery is not installed in the vehicle, connect
the clamp directly to the negative terminal of the battery
(- symbol).
CHARGING
- Power the battery charger by inserting the power cable into
the mains socket.
- During this phase the battery charger keeps the charging
current constant.
END OF CHARGING
- The battery charger FULL LED “
” lights up to signal
that charging has ended.
- Disconnect the power supply to the battery charger by
removing the power supply cable from the mains outlet.
- Disconnect the black charge clamp from the chassis of
the vehicle or from the negative terminal of the battery (-
symbol).
- Disconnect the red charge clamp from the positive terminal
of the battery (+ symbol).
- Store the battery charger in a dry place.
- Close up the battery cells with the appropriate plugs (if
present).
MAINTENANCE (enabled in TRONIC or PULSE TRONIC
mode only)
- Leave the battery charger connected to the mains.
- Do not interrupt the charge process.
- Leave the charge clamps connected to the battery even
after the charge process has been completed.

Chat with your Telwin Defender 8 manual using AI

Get instant AI answers from your Telwin Defender 8 manual

Ask anything about the Telwin Defender 8. Answers come from this manual, with the pages they are based on.

Defender 8 Maintenance Schedule

Before each charge
Check electrolyte level and add distilled water if needed

Ensure the electrolyte covers the battery plates. If not, add distilled water up to 5-10 mm above the plates.

Before each charge
Clean battery terminals of oxidation

Remove any oxide from positive and negative terminals to ensure good contact with the charging clamps.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Defender 8?

Yes No

Frequently Asked Questions

A

Yes, this model is suitable for charging both free electrolyte lead-acid batteries and sealed batteries found in cars, motorcycles, and boats.

Is this answer helpful?

A

The charger has internal protection against polarity reversal, but it does not provide a specific signal warning. Always double-check the red clamp goes to positive and black to negative.

Is this answer helpful?

A

No, never use the battery charger inside a car or under the bonnet. Use it in a garage or open space to allow explosive gases to escape safely.

Is this answer helpful?

A

When the charging is complete, the FULL LED indicator will light up to signal that the process has ended successfully.

Is this answer helpful?

A

Children aged 8 and above may use it only under supervision or after receiving proper instruction on safety hazards and correct usage.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Automatically detects 6V and 12V battery voltages for versatile use
  • Includes multiple safety protections against overload and short circuits
  • Clear LED indicators show charging status and completion easily
VS

Disadvantages

  • No signal warning if battery polarity is reversed by mistake
  • Requires careful handling due to corrosive electrolyte risks
  • Must be used in well-ventilated areas to avoid gas accumulation
M: QW-35-FL

Product Specification

Suitable for

AGM, Lead, EFB, Gel

Battery voltage

6V, 12V

Max charging current

750mA

Battery capacity

2-20Ah

Display

LED

Color

white, black

Dimensions

1.97x3.15x1.18in (WxHxD)

Weight

7.76oz

M: QW-35-FL

Product Description

Telwin Defender 8: The Ultimate Guide to Safe and Efficient Battery Charging

The Telwin Defender 8 is a robust battery charger designed for petrol and diesel vehicles, motorcycles, and boats. It handles both free electrolyte lead-acid batteries and sealed types with ease. This device operates on a single-phase power supply ranging from 100V to 240V at 50/60Hz. Its intelligent electronics ensure a constant current and voltage charge following the IU curve, automatically detecting whether your battery requires 6V or 12V. With a charging current of 0.75A, it provides a gentle yet effective recharge cycle.

Safety is paramount when using the Telwin Defender 8 Manual instructions. Before connecting the unit, always ensure the area is well-ventilated to disperse explosive gases generated during charging. Never smoke near the battery. The device features clear LED indicators; the CHARGE light signals active charging, while the FULL light confirms the process is complete. Users must connect the red clamp to the positive terminal and the black clamp to the vehicle chassis or negative terminal, avoiding fuel lines. The charger includes internal electronic safeguards against overloads, short circuits, and polarity reversal.

For maintenance modes like TRONIC or PULSE TRONIC, the unit can maintain battery voltage automatically without interruption. Always disconnect the mains cable before performing any simple maintenance or changing connections. Clean terminals regularly to prevent oxidation and ensure good contact. Store the charger in a dry place after use. By following these guidelines, you extend the life of your battery and ensure safe operation.

M: QW-35-FL

© Copyright 2026 Manual.ly