Manual.ly Logo

TechN RTX 2080 Ti Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: QW-35-FL
page

/ 2

Loading...
a104fb0c5abd710f02389533fb0625d23160 page 1
Empfohlene Werkzeuge (nicht enthalten) //
Suggested tools (not included)
• Weiches Papiertuch und Isopropanol zum Reinigen der GPU
• Phillips-Schraubendreher
• Soft paper towel and Isopropanol to clean the GPU
• Phillips screwdriver
Haftungsausschluss // Disclaimer
Alle Kühler sind auf Dichtigkeit getestet. Mit der Demontage des
Kühlers erlischt die Dichtigkeitsgarantie der TechN GmbH.
Unsachgemäße Montage des Kühlers kann zu Schäden an der
Grakkarte und dem PC führen. TechN GmbH übernimmt keine
Haftung für Schäden durch unsachgemäße Installation.
All coolers are leak tested. If you disassemble the cooler the leak
warranty will be voided. Improper installation can damage the graphics
card and your PC. TechN GmbH assumes no liability for any damage
caused by improper installation.
*Lies zunächst alle Schritte bevor du anfängst*
*Please read all steps before starting*
1b. Kompatibilität prüfen // Check compatibility
Prüfe die Kompatibilität auf www.techn.de/compatibility
Check compatibility online at www.techn.de/compatibility
2. Original Kühler demontieren //
Disassemble stock cooler
Entferne beide Slotblendenschrauben, alle gekennzeichneten
Außensechskant-Abstandshalter und Schrauben von der
Rückseite des PCB. Demontiere den Luftkühler und ziehe das
Lüfterkabel ab.
Remove the two slot bracket screws, all the highlighted hex spacers
and screws on the back of the PCB. Dismount the air cooler. Don’t
forget to unplug the fan.
1a. Original Backplate demontieren //
Disassemble stock backplate
Löse die Schrauben der Backplate und demontiere diese.
Unscrew and dismount the backplate as illustrated.
4. Grakkarte reinigen // Clean the graphics card
Entferne die alte Wärmeleitpaste mit Isopropanol und einem
weichen Papiertuch. Achte darauf, dass die Grakkarte staub-,
fussel- und fettfrei ist.
Remove the stock thermal paste using isopropanol and a soft paper
towel. Make sure that the graphics card is completely clean.
5. Wärmeleitpaste auftragen // Apply thermal paste
Trage nach der Reinigung die mitgelieferte Wärmeleitpaste auf die
GPU auf. Der Tropfen sollte ca. 3mm im Durchmesser sein.
After cleaning, apply the provided thermal paste onto the GPU. The
drop should be around 3mm in diameter.
6.
Schutzfolie entfernen // Remove protective lm
Entferne die Schutzfolie von allen Wärmeleitpads. Überprüfe
deren Position nach Abbildung auf der Rückseite.
Remove the protective lm from each of the thermal pads.
Compare their positioning with the gure on the back.
3. Slotblende verschrauben // Fasten slot bracket
Befestige die Slotblende mit den mitgelieferten Schrauben (lang)
und Muttern, platziere hierbei eine Unterlegscheibe zwischen
Mutter und PCB.
Secure the slot bracket using the two included screws (long) and
nuts, don’t forget to place a washer between the nut and the PCB.
7. Montage // Assembly
Lege den Kühler umgedreht auf die Verpackungsbox. Positioniere
das PCB auf dem Kühler, achte hierbei auf die Ausrichtung der
Befestigungslöcher.
Place the cooler bottom up on the packaging box. Position the PCB
on the cooler. Make sure that the mounting holes are aligned.
Bedienungsanleitung
User Manual
8a. Verschrauben // Fasten screws
Platziere unter jeder Schraube (kurz) eine Unterlegscheibe.
Verschraube die 4 gekennzeichneten GPU Schrauben
gleichmäßig über Kreuz.
Fasten the 4 highlighted GPU screws (short) crosswise and evenly,
place a washer underneath each screw.
Wasserkühler mit G¼“ Anschluss
Water block with G¼“ connector
Wärmeleitpads (vorinstalliert)
Thermal pads (preinstalled)
2 Muttern M3
2 Nuts M3
Wärmeleitpaste
Thermal paste
Bedienungsanleitung
User Manual
13 Schrauben M3x4 mm (kurz)
13 screws M3x4 mm (short)
15 Unterlegscheiben
15 Plastic washers
Packungsinhalt // Box content
TIPP: Durch Entfernen des originalen Kühlers kann die Garantie der
Grakkarte erlöschen. Verwende nur Kühlüssigkeit mit Korrosionsschutz.
TIP: By removing the stock cooler, warranty of the graphics card can
be voided. Only use coolant with anti-corrosion additives.
WARNUNG! Verwende nicht zu viel Kraft bei der Installation des
Kühlers und dem Verschrauben. Chip Dies können leicht brechen.
ATTENTION! Do not to use too much force by pressing the block
down onto the PCB or overtightening the screws. Chip dies are
prone to cracking.
1.
4.
2.
3.
Unterlegscheibe M3x4mm
Washer M3x4mm
Mutter M3
Nut M3
Schraube M3x6mm (lang)
Screw M3x6mm (long)
2 Schrauben M3x6 mm (lang)
2 screws M3x6 mm (long)
GPU Waterblock
RTX 2080Ti

Chat with your TechN RTX 2080 Ti manual using AI

Get instant AI answers from your TechN RTX 2080 Ti manual

Ask anything about the TechN RTX 2080 Ti. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend RTX 2080 Ti?

Yes No

Frequently Asked Questions

A

Yes, removing the original stock cooler and disassembling the unit typically voids the graphics card manufacturer's warranty. Additionally, the TechN leak warranty is voided once the cooler is taken apart.

Is this answer helpful?

A

You will need a Phillips screwdriver, a soft paper towel, and isopropanol for cleaning. You must also have compatible tubing and a pump reservoir for your liquid cooling loop ready before starting.

Is this answer helpful?

A

Plug the 4-pin connector into the motherboard RGB_HEADER. Ensure the arrow on the plug points to the +12V line. Incorrect polarity can damage your motherboard or the LED strip.

Is this answer helpful?

A

Yes, it is strongly recommended to perform a 24-hour leak test with the PC powered off to ensure there are no leaks before running the system under load.

Is this answer helpful?

A

Always use coolant that contains anti-corrosion additives to protect the copper and aluminum components inside the water block from corrosion and degradation over time.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Precision engineering made in Berlin with leak-tested quality assurance
  • Effective thermal management for the RTX 2080 Ti under heavy loads
  • Integrated RGB LED with easy 4-pin motherboard connection
  • Complete kit includes thermal paste, pads, screws, and fittings
VS

Disadvantages

  • Installation voids the manufacturer's leak warranty immediately
  • Risk of damaging chip dies if screws are over-tightened
  • Requires removal of stock cooler which may void card warranty
  • Complex assembly process requiring specific tools and careful handling
M: QW-35-FL

Product Specification

Type

GPU

Material

Copper (nickel-plated), Aluminum, PMMA

Compatibility

NVIDIA GeForce RTX 2080 Ti Founders Edition

Connections

G1/4"

Lighting

LED (RGB)

Dimensions (LxWxH)

10.43x4.92x1.02 in

Weight

2.34 lbs

Features

Voltage converter cooled with GPU

M: QW-35-FL

Product Description

TechN RTX 2080 Ti Schwarz: Ultimate Water Cooling Upgrade

The TechN RTX 2080 Ti schwarz represents the pinnacle of custom liquid cooling solutions for high-performance graphics cards. Designed in Berlin, Germany, this water block transforms your stock air cooler into a silent and efficient cooling system capable of handling extreme thermal loads. The sleek black finish not only matches premium builds but also ensures that your hardware remains visually striking while operating at lower temperatures.

Installation requires precision and care. The process begins with removing the original air cooler and backplate from the graphics card. Users must thoroughly clean the GPU die and memory modules using isopropanol and a soft paper towel to remove all old thermal paste. A precise 3mm drop of high-quality thermal paste is applied to the GPU before attaching the water block. The kit includes necessary hardware such as M3 screws, washers, and pre-installed thermal pads positioned according to detailed diagrams.

A critical aspect of this product is its integration with RGB lighting. The unit features a dedicated 4-pin connector that plugs directly into the motherboard's RGB header. It is vital to align the arrow on the connector with the +12V line to prevent damage to the motherboard or LED components. Once assembled, the tubing connects to two G1/4-inch fittings, leaving the other ports sealed with provided plugs.

Safety warnings are paramount during installation. Over-tightening screws can crack the chip dies, so torque must be managed carefully. Additionally, disassembling the cooler voids the leak warranty, so users should proceed with caution. A 24-hour leak test with the PC turned off is highly recommended before full operation. Only use coolant containing anti-corrosion additives to protect the internal channels. This manual guides you through every step, ensuring a secure and effective upgrade for your gaming or workstation rig.

M: QW-35-FL

© Copyright 2026 Manual.ly