Manual.ly Logo

SW-Stahl S3249 Manual

0.0 · 0 Ratings

PDF manual · 16 Pages

English

M: OA-GPT-5-NAN
page

/ 16

Loading...
302532d19c1e18eaf2d2165aa3d9aa3d1ce4 page 7
7
COMMISSIONING:
1.
Before operation, put a few drops of acid- and resin-free pneumatic oil in the air inlet of the tool.
2. Before connecting the tool, clean the couplers and hoses by blasting them briey with air. Make
sure hose and couplers have a sufcient diameter.
NOTE: THE DIAMETERS OF COMPRESSED AIR HOSES ARE USUALLY CHOSEN TOO SMALL,
NEVER TOO LARGE!
3. The operating pressure measured under load at the tool air inlet should be 6.3 bar. A higher
pressure means greater wear and can cause damage to the tool. A fall in pressure to 5.5 bar
means extreme loss of power.
4. Good air quality is vital for any pneumatic tool. The air must be clean, dry and lubricated. The
best solution is a complete maintenance unit comprising an air lter, regulator and oil-fog
lubricator which is no more than 6-8 m away from the tool. The oiler should be set to 3-6 drops
per minute (inspection glass). The length of the hose between tool and maintenance unit should
not exceed 8 m.
5. We recommend using a central oiler unit for optimum tool lubrication. Up to 80% oil can be
saved, which also improves the quality of the air inhaled by the user of course, since no excess oil
is expelled to the air.
6. The hammer mechanism of the impact screwdriver should be lubricated lightly after 60 working
hours at the latest. Too much grease will impair the power of the impact screwdriver since the
hammer mechanism will become sticky.
7. If the tool is not to be used for a longer period, it must be lubricated thoroughly before storage.
Before re-use, please heed points 1 and 2.
8. Output and direction of rotation are adjusted by turning the lever. Clockwise = arrow to the right
/ Anti-clockwise = arrow to the left.
9. Output can be adjusted in three stages for clockwise and one stage for anti-clockwise direction
using the lever.

Chat with your SW-Stahl S3249 manual using AI

Get instant AI answers from your SW-Stahl S3249 manual

Ask anything about the SW-Stahl S3249. Answers come from this manual, with the pages they are based on.

S3249 Maintenance Schedule

Every 60 hours
Lubricate hammer mechanism

Lightly lubricate the hammer mechanism after 60 working hours at the latest. Too much grease will impair power.

Before storage
Lubricate tool for long-term storage

If the tool is not to be used for a longer period, it must be lubricated thoroughly before storage.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend S3249?

Yes No

Frequently Asked Questions

A

The tool should be supplied with 6.3 bar measured at the tool inlet under load. Higher pressures increase wear and risk damage; a drop to around 5.5 bar causes significant power loss.

Is this answer helpful?

A

Lightly lubricate the hammer mechanism after a maximum of 60 working hours. Over-greasing can cause the hammer to stick and reduce performance. For storage, thoroughly oil the tool before long periods of inactivity.

Is this answer helpful?

A

Use a maintenance unit comprising an air filter, regulator and oil-fog lubricator installed within 6–8 m of the tool. Set the oiler to 3–6 drops per minute and keep the hose between unit and tool under 8 m for best results.

Is this answer helpful?

A

Only use impact-rated sockets. For drive squares with a bore, secure the socket with a steel pin and rubber ring; if fitted with a spring ring, check tension regularly. An unsecured socket can detach and cause injury.

Is this answer helpful?

A

Due to high noise and operational hazards, always wear hearing protection, safety gloves and goggles. Avoid loose clothing and tie back long hair. Inspect air hoses and couplings before use and do not use damaged hoses.

Is this answer helpful?

A

Key specs: 9,000 U/min no-load speed, 12.5 mm (1/2") drive, 610 Nm rated torque, 1,172 Nm max loosening torque, 6.3 bar operating pressure, 127 l/min air consumption, length 281 mm, weight 1.11 kg.

Is this answer helpful?

A

No. The pneumatic impact wrench is intended solely for loosening and tightening screws and bolts. Using it for other tasks or modifying the tool voids the warranty and can be dangerous.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • High maximum torque: 610 Nm rated, 1,172 Nm loosening torque for demanding jobs.
  • Compact and lightweight: 1.11 kg and 281 mm length for comfortable handling.
  • Fast no-load speed: 9,000 U/min for efficient fastening and removal.
  • Clear maintenance guidance: recommended filter-regulator-oiler setup and lubrication intervals.
  • Robust safety compliance: meets relevant EU standards and includes explicit safety instructions.
VS

Disadvantages

  • Loud operation: 94.2 dB(A) sound pressure and 105.2 dB(A) sound power—requires PPE.
  • Air-hungry: 127 l/min consumption and needs stable 6.3 bar under load.
  • Vibration level: about 7.3 m/s²—possible operator fatigue over long periods.
  • Maintenance-dependent: requires regular lubrication and correct air treatment to avoid damage.
  • Specialized sockets required and must be securely fastened to avoid accidents.
M: OA-GPT-5-NAN

Product Specification

Type

Impact wrench

Operating pressure

91.38 psi

Air consumption

6.00 cfm

No-load speed

9000/min

Torque

228.67 ft-lb

Loosening torque

864.42 ft-lb

Tool reception

1/2" Square

Features

Forward/reverse rotation, Torque preselection, Soft grip, Vibration damping

Weight

2.45 lb

M: OA-GPT-54-NAN

Product Description

SW-Stahl S3249 pneumatic impact wrench Manual

The SW-Stahl S3249 pneumatic impact wrench is a high-performance 1/2" (12.5 mm) impact tool designed for professional workshops and demanding industrial use. With a no-load speed of 9,000 U/min and a rated torque of 610 Nm (maximum loosening torque up to 1,172 Nm), this compact, lightweight unit delivers powerful turning force while remaining easy to handle. At just 1.11 kg and 281 mm long, the tool balances portability and output, making it suitable for repetitive fastening tasks and heavy-duty loosening jobs alike.

Built for compressed-air operation, the S3249 runs best at a nominal operating pressure of 6.3 bar and consumes approximately 127 l/min of air. The tool connects via a 1/4" compressed air coupling and produces measured vibration around 7.3 m/s². Acoustic levels are significant—94.2 dB(A) sound pressure and 105.2 dB(A) sound power—so hearing protection is mandatory during use.

Performance and longevity depend heavily on proper air supply and maintenance. The manual emphasizes clean, dry, and lubricated air delivered through a maintenance unit (filter, regulator, oiler) placed within 6–8 m of the tool, with the oiler set to 3–6 drops/min and hose length kept below 8 m. Under-load inlet pressure should be 6.3 bar; higher pressures accelerate wear, while drops to ~5.5 bar lead to severe power loss. Regular light lubrication of the hammer mechanism after about 60 working hours and thorough oiling before long-term storage help avoid sticky or worn internal parts.

Operation is straightforward: a three-stage lever setting for clockwise output and a single stage for counterclockwise allows controlled torque application and reverse rotation. Direction is selected by lever orientation (arrow right = clockwise, arrow left = counterclockwise). Use only suitable impact-rated sockets secured to the 1/2" square drive—either with a steel pin and rubber ring or a properly tensioned spring ring—to prevent sockets from coming loose.

Safety is stressed throughout: wear ear protection, safety goggles, and gloves; avoid loose clothing and secure long hair; inspect hoses and couplings for damage; and do not run the tool at high idle with a socket attached. The tool should only be used for fastening and loosening screws and bolts—misuse or unauthorized modification voids warranty. SW-Stahl declares conformity with relevant EU machinery directives and safety standards.

Notes:

  • Optimum performance requires a maintenance unit (filter, regulator, oiler) within 6–8 m of the tool.
  • Set oiler to 3–6 drops per minute and keep hose length under 8 m.
  • Lubricate the hammer mechanism after 60 working hours; avoid over-greasing.
  • Use hearing protection; tool exceeds 94 dB(A) sound pressure.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly