Manual.ly Logo

SW-Stahl S3224 Manual

0.0 · 0 Ratings

PDF manual · 10 Pages

English

M: QW-35-FL
page

/ 10

Loading...
91d1038611c6bbaa7d6a9922849c3d6071bd page 7
7
S3224
7. Followairsourcemanufacturersdirectionsforconnectionsofregulators,ltersand
other accessories to air source. Do not install quick couplers directly on tool as they put
unnecessary strain on the air inlet threads possibly causing them to wear out
prematurely. Instead, install them on a short length of air hose attached to the tool.
We cannot accept any guarantee for damages caused by non-observance of these operating
instructions or by improper repair. We reserve the right to make changes in the interest of technical
progress.
INBETRIEBNAHME
1. Select lowest torque to solve glow plugs or other sensitive couplings.
Torque settings can be adjusted for this impact wrench in the following 4 steps for the
left rotation: 1 = 10 Nm, 2 = 20 Nm, 3 = 30 Nm, 4 = 40 Nm
2. Turn the air regulator to lowest position and increase the performance until the nut or
bolt moves gradually. Warning: If pressing the trigger for longer time and the highest
torque level of the torque controller is set, there is a danger that the glow plug breaks
off when releasing! Always check the torque with a torque wrench by manufacturer´s
instructions.
3. Do not tighten nuts or screws with higher torque than allowed. Put nut or screw in the
thread and start attach several revolutions by hand. With the impact wrench tighten the
screwuntilitrestsushagainstthesupportingsurface.
AIR SOURCE
Clean air of correct air pressure is recommended for the power supply for this tool. A maximum of
90PSI atthetoolis recommendedformost airtoolsofthisclass.Checkspecicationssection for
recommended pressure. (Depending on length of air hose and other circumstances, air pressure at
compressor may need to be increased to 100 PSI to ensure 90 PSI at the tool.) Water in the air hose
and compressor tank contributes to reduced performance and damage of the air tool. Drain the air
tankand ltersbeforeeachuse andas necessarytokeeptheairsupplydry.Hose lengthover25“
causes loss in line pressure. Increase hose ID or increase compressor pressure to compensate for the
pressure loss. Use an in-line pressure regulator with gauge if air inlet pressure is critical.

Chat with your SW-Stahl S3224 manual using AI

Get instant AI answers from your SW-Stahl S3224 manual

Ask anything about the SW-Stahl S3224. Answers come from this manual, with the pages they are based on.

S3224 Maintenance Schedule

Before each use
Lubricate the tool with air tool oil

Place 4 to 5 drops of air tool oil into the air inlet before every use to ensure proper lubrication and prevent damage.

Before each use
Drain water from the air system

Drain water from hoses, compressors, tanks, and filters before each use to prevent performance loss and internal corrosion.

M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend S3224?

Yes No

Frequently Asked Questions

A

The maximum recommended air pressure is 6.3 bar or approximately 90 PSI. Higher pressures may require compensation if hose length causes pressure drop.

Is this answer helpful?

A

The wrench features four stages: Stage 1 is 10 Nm, Stage 2 is 20 Nm, Stage 3 is 30 Nm, and Stage 4 is 40 Nm. Start with the lowest setting for delicate work.

Is this answer helpful?

A

Water in the air line can destroy the tool internally and cause significant power loss. Draining ensures dry air reaches the mechanism.

Is this answer helpful?

A

No, you must only use IMPACT rated sockets. Standard sockets may shatter under the high impact forces generated by this pneumatic tool.

Is this answer helpful?

A

The set includes five hexagon sockets (8-12 mm), two extension bars (50 mm and 100 mm), and a quick-action coupling.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Compact design ideal for tight spaces
  • Four-stage adjustable torque for sensitive parts
  • Includes complete 9-piece accessory kit
  • Lightweight at only 2.12 kg for reduced fatigue
VS

Disadvantages

  • Requires regular lubrication to maintain performance
  • Sensitive to water contamination in air lines
  • High noise level of 103.2 dB requires hearing protection
  • Must use specific impact sockets not standard ones
M: QW-35-FL

Product Specification

Type

Impact wrench

Operating pressure

91.4 psi

Torque

29.56 lb-ft

Drive size

1/4" square

Features

Right/left rotation, torque preselection

Weight

4.67 lbs

Package contents

8-piece accessory set

M: QW-35-FL

Product Description

SW-Stahl S3224 Pneumatic Impact Wrench with Accessories - Read, Download & Print Free

The SW-Stahl S3224 Pneumatic Impact Wrench is a compact and powerful tool designed specifically for the demanding task of removing jammed glow plugs and stubborn fasteners. This nine-piece set offers exceptional versatility, featuring a right-and-left rotation capability and a four-stage adjustable loosening torque that ranges from 10 to 40 Nm. Its small size makes it highly maneuverable in tight engine compartments where larger tools cannot fit.

This impact wrench comes equipped with essential accessories including five IMPACT hexagon sockets measuring 50 mm long (sizes 8-12 mm) and two extension bars of 50 mm and 100 mm. The unit operates on standard 6.3 mm air connections and weighs only 2.12 kg, ensuring reduced operator fatigue during extended use. Proper maintenance is critical; users must lubricate the tool with four to five drops of air tool oil before each operation and ensure the air supply system is free of moisture to prevent internal damage.

Safety is paramount when operating this device. Always wear approved eye protection and avoid loose clothing or jewelry that could get caught in moving parts. The tool requires a clean air source with a maximum pressure of 6.3 bar (90 PSI). Adjusting the torque settings allows for gentle removal of sensitive components without risking breakage. After installation, all fasteners should be verified with a torque wrench to meet manufacturer specifications. This reliable pneumatic solution combines durability with precision control for professional automotive repair tasks.

M: QW-35-FL

© Copyright 2026 Manual.ly