Manual.ly Logo

SolaX Power Triple Power HV10230 Manual

0.0 · 0 Ratings

PDF manual · 24 Pages

English

M: QW-35-FL
page

/ 24

Loading...
ea347a8f7b768439da03581d268b9a70f9e7 page 16
36
37
6 Troubleshooting
6.1 Troubleshooting
Check the previous indicators to determine the status of the T-BATsystem.
A warning state is triggered when conditions such as voltage or temperature
exceed the design limitations. T-BAT system's BMSperiodically reports its
operating state to the inverter.
When the T-BAT system falls outside the prescribed limits, it entersinto a
warning state.
Use the monitoring software on the inverter to identify what caused the warning.
The possible error messages are as follows:
6. Troubleshooting
When a warning is reported, the inverter immediately stops its operation.
6. Troubleshooting
Check if the communication
cable between BMS and
inverter is correctly and well
connected.
1. Move the DIP switch to the
correct position;
2. Check if the communication
cable between battery
modules is correctly and well
connected.
BMS_Internal_Err
1) DIP switch on the
wrong position
2) The communication
between battery
modules is interrupted.
1) Move the DIP switch to the
correct position
2) Check if the communication
cable between thebattery
modules is correctly and
properly connected.
BMS_OverVoltage Battery over voltage
BMS_LowerVoltage
Battery under voltage
BMS_ChargeOCP
Battery charge over
current protection
Error Messages Description Troubleshooting
Contact your distributor or
SolaX directly for servicing.
Contact your distributor or
SolaX directly for servicing.
Contact your distributor or
SolaX directly for servicing.
BMS_Ver_Unmatch
The version of
BMS isunmatched
Contact your distributor or
SolaX directly for servicing.
BMS_DishargeOCP
Battery discharge over
current protection
Contact your distributor or
SolaX directly for servicing.
1) Ensure the power cable is
correctly and properly connected to
the power connector (XPLUG) of
theBMS
2) If the first step still does not
work, contact your distributor or
SolaX directly.
BMS_TemHigh
Battery over
temperature
BMS_TemLow
Battery under
temperature
BMS_Hardware_Protect
Battery hardware
under protection
BMS_Insulation_Fault
Battery insulation
fault
BMS_VoltSensor_Fault
Battery voltage
sensor fault
BMS_TempSensor_Fault
Battery
temperature
sensor fault
BMS_CurrSensor_Fault
Battery current
sensor fault
BMS_Relay_Fault Battery relay fault
BMS_Type_Unmatch
The type of BMS
isunmatched
Warning Messages Description Troubleshooting
Contact your distributor or
SolaX directly for servicing.
Contact your distributor or
SolaX directly for servicing.
Contact your distributor or
SolaX directly for servicing.
Contact your distributor or
SolaX directly for servicing.
Contact your distributor or
SolaX directly for servicing.
Contact your distributor or
SolaX directly for servicing.
Wait until the temperature of the
cells returns to the normal state.
Wait until the temperature of the
cells returns to the normal state.

Chat with your SolaX Power Triple Power HV10230 manual using AI

Get instant AI answers from your SolaX Power Triple Power HV10230 manual

Ask anything about the SolaX Power Triple Power HV10230. Answers come from this manual, with the pages they are based on.

Triple Power HV10230 Maintenance Schedule

Remind me when maintenance is due
Every 3 Months
Charge stored batteries if ambient temp is -20 to 45 C

If the storage environment temperature is between -20 and 45 degrees Celsius, charge the batteries at least once every 3 months.

Show in the manual (page 22)
Every 6 Months
Charge stored batteries if ambient temp is -20 to 20 C

If the storage environment temperature is between -20 and 20 degrees Celsius, charge the batteries at least once every 6 months.

Show in the manual (page 22)
After 9 Months of Non-Use
Charge battery to at least 50% SOC after long inactivity

If the battery has not been used for more than 9 months, it must be charged to a State of Charge (SOC) of at least 50%.

Show in the manual (page 22)

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend Triple Power HV10230?

Yes No

Frequently Asked Questions

A

No, the installation must be performed by a qualified electrician familiar with high-voltage systems and local regulations. Improper installation can void warranties and pose safety risks.

Is this answer helpful?

A

A single T-BAT system can support a maximum of four HV10230 battery modules connected together. Exceeding this limit may damage the fuse and the battery modules.

Is this answer helpful?

A

The BMS uses LED indicators on the front panel. During charging, blue LEDs flash in a specific pattern based on SOC, while discharging shows a different flashing sequence.

Is this answer helpful?

A

If the ambient temperature exceeds safe operating limits, the battery pack will automatically stop operating to protect itself from heat damage and potential fire hazards.

Is this answer helpful?

A

Yes, the IP65 rating protects against dust and water jets, making it suitable for outdoor use, provided it is installed in a shaded, cool area away from direct sunlight and flammable materials.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High energy efficiency with 95% roundtrip rate
  • Long cycle life exceeding 6000 cycles at 90% DOD
  • IP65 rated for dust and water resistance
  • Scalable design supporting up to four modules
  • Advanced BMS with real-time status monitoring
VS

Disadvantages

  • Requires professional installation by qualified electricians only
  • Strict temperature constraints for charging and discharging
  • Limited to residential use, not suitable for commercial applications
  • Initial setup requires precise alignment and torque specifications
  • Battery must be charged if stored unused for more than one month
M: QW-35-FL

Product Specification

Note

Prices may include 0% VAT rates for AT and DE

Compatible with

SolaX Power Triple Power T30

Battery type

LiFePO4

Battery modules

1 module (max. 4)

Rated capacity

30Ah, 8.27kWh

Rated voltage

102.4V

Discharge current

25A

Discharge power

2.6kW

Operating temperature

14F to 122F

Lifespan

10 years, 6000 charge cycles

Display

No

Mounting type

Freestanding (stackable)

Protection class

IP65

Dimensions

19x6x18.6in (WxHxD)

Weight

76.06lbs

M: QW-35-FL

Product Description

Unlocking the Potential of SolaX Power HV10230 Storage Module

The SolaX Power HV10230 Storage Module represents a significant leap forward in residential energy storage technology. Designed for seamless integration with the T-BAT series, this high-voltage lithium-ion battery system offers homeowners a reliable and efficient way to manage their energy consumption. With a nominal capacity of 30Ah and an operating voltage range tailored for high-voltage applications, the HV10230 ensures that your solar investment is maximized by storing excess power for use during peak hours or outages.

One of the standout features of this module is its impressive cycle life, boasting over 6000 cycles at 90% depth of discharge. This longevity translates to years of consistent performance, making it a cost-effective solution for long-term energy independence. The system achieves a roundtrip efficiency of 95%, ensuring minimal energy loss during charge and discharge cycles. Whether you are looking to reduce electricity bills or prepare for grid instability, the HV10230 provides the robustness needed for modern households.

Installation is streamlined for qualified electricians, with clear guidelines provided for wall or floor mounting. The unit comes with comprehensive safety protocols, including IP65 protection against dust and water ingress, which allows for flexible placement in various environments. The built-in Battery Management System (BMS) actively monitors cell health, temperature, and voltage, providing real-time status indicators via LED lights. This intelligent management prevents overheating and extends the lifespan of the battery pack.

Key Considerations for Installation

When integrating the SolaX Power HV10230 into your home energy system, attention to detail is crucial. The manual emphasizes the importance of maintaining proper spacing around the unit for ventilation, as well as adhering to strict electrical connection procedures. Users must ensure that all connections are secure and that the grounding requirements are met to prevent potential hazards. The system supports stacking up to four modules, allowing for scalable energy solutions that grow with your needs.

Important Notes

  • Always wear insulated gloves and safety goggles during installation.
  • Do not expose the battery to temperatures exceeding 140°F.
  • Ensure the manufacturing date difference between stacked modules does not exceed three months.
  • Follow local regulations regarding fire extinguishers and emergency response.
M: QW-35-FL

© Copyright 2026 Manual.ly