Manual.ly Logo

SKS S-Board Manual

0.0 · 0 Ratings

PDF manual · 1 Pages

English

M: OA-GPT-5-NAN
page

/ 1

Loading...
7ea6f478b2adafde777869284607efdcff48 page 1
MADE IN GERMANY SKS-GERMANY.COM
GERMANY
MONTAGEANLEITUNG S-BOARD ¬ 11317
ROAD
ALLROAD
MOUNTAIN
REIFENBREITE
TYRE WIDTH
38
mm
MAX.
DE. S-BOARD
Clip-on front mudguard for racing bikes, cyclocross bikes, hybrid bikes and gravel bikes. For a max. tyre width of 38 mm. The S-BOARD is the ideal companion for our S-BLADE
rear mudguard. Its light, double-hinged quick release tting system also ts aero forks.
Mounting instructions: The S-BOARD is to be mounted on the fork so that there is a minimum clearance of 1.5 cm between the mudguard and the tyres
all-round. CAUTION! Only tighten the screws with max. 1 NM!
1
Initially position at point A the mudguard on the fork so that the minimum clearance to the tyre of 1.5 cm is ensured. This can be ascertained by pushing it up or down (Arrow
B). Now tighten the quick release rubber around the fork and hook it into the fastening tabs, so that it is unable to slip on the fork (see 1a.).
1a
Use the enclosed paintwork protection in order to protect the frame. Please see the section entitled »Permanent attachment of the mudguards« for information regarding the
permanent attachment of the mudguard with not enclosed cable ties.
2
Now adjust the angle of the mudguard, by loosening the screws and moving the mudguard, within the elongated eyelets at the end of the plastic stays, so that the clearance
between the mudguards and the tyres is a min. of 1.5 cm all-round.
Now retighten the screws (max. 1 NM) so that the mudguard now rmly remains in position.
2a
Where necessary, carefully shorten the clamping rubbers with a scissors so that the ends cannot come into contact with the wheel spokes.
Permanent mounting of the mudguards
In order to fasten with quick release clamping rubbers, the S-BOARD can also be attached with cable ties (C). This type of fastening is only suitable for a permanent mounting and
as protection against the S-BOARD being stolen from the bike. In order to assemble the mudguard, use a further 2 cable ties per side in addition to the clamping rubbers. Ensure
that the cable ties run precisely in the grooves provided for this purpose. Pull the cable ties as tight as possible in order so that slipping cannot occur. Carefully cut the protruding
ends of the cable ties using scissors.
Safety instructions!
Before each journey, check that the mudguard is sitting correctly. If the minimum distance between the mudguard and the tyre is not observed, the mudguard may become
damaged and, in the worst case scenario, could lead a crash. Therefore, it is essential that the minimum distance of 1.5cm is observed during assembley. Ensure that the awless
function of the brakes is guaranteed and that the mudguard does not come into contact with the moving brake parts. Due to the eect of UV radiation, the clamping rubbers are
subject to natural aging. Regularly check the condition of the clamping rubbers and promptly replace them in the event of damage. Please check screws before each ride to insure
they are tight to 1NM.
MONTAGEVIDEO YOUTUBE
MOUNTINGVIDEO YOUTUBE
ACHTUNG! SKS haftet nicht für Schäden an Rahmenlackierung oder Carbon, die aus der Nut-zung dieses Produkts resultieren. Der sachgemäße Gebrauch der
Schutzfolie sowie regelmäßige Wartung inklusive der Reinigung des Rahmens und der Radschützer im Bereich der Befestigungspunkte beugen möglichen
Schäden vor.
LACKSCHUTZFOLIE
PAINTWORKPROTECTION
1a.
C
C
2a.
SW 2,5
INBUS/ALLEN MAX. 1
LANGLOCH
ELONGATED EYELET
2.
1.
B
A
B

Chat with your SKS S-Board manual using AI

Get instant AI answers from your SKS S-Board manual

Ask anything about the SKS S-Board. Answers come from this manual, with the pages they are based on.

S-Board Maintenance Schedule

Remind me when maintenance is due
Before each ride
Check mudguard fit and tyre clearance

Check that the mudguard is correctly seated and maintains at least 1.5 cm clearance from the tyre. Ensure it does not contact moving brake parts.

Before each ride
Check screw tightness

Check that screws are tightened to 1 Nm.

Regularly
Inspect clamping rubbers

Check clamping rubbers for UV-aging damage and replace them promptly if damaged.

Regularly
Clean mounting areas

Clean the frame and mudguards around fastening points as part of regular maintenance to help prevent damage.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: gpt-5.6-terra

Ask a Question

0/1000

Do you recommend S-Board?

Yes No

Video Manual

Montage vom S-BOARD | mounting the S-BOARD

Frequently Asked Questions

A

The S-Board supports tyres up to a maximum width of 38 mm, making it suitable for road, all-road, cyclocross, hybrid and many gravel setups within that limit.

Is this answer helpful?

A

Maintain a minimum 1.5 cm (15 mm) clearance all around between the mudguard and the tyre to prevent contact that could cause damage or a crash. Check clearance before every ride.

Is this answer helpful?

A

Yes. In addition to the quick-release bungee cords, you can secure the S-Board permanently with two cable ties per side to prevent slipping and deter theft. Tighten ties fully and trim excess tails carefully.

Is this answer helpful?

A

Tighten the mounting screws to a maximum of 1 Nm (use a 2.5 mm Allen key). Exceeding this torque can damage fittings or the fork.

Is this answer helpful?

A

Use the included paintwork protection film at contact points, and regularly clean attachment areas. Despite precautions, SKS is not responsible for paint or carbon damage, so careful installation and maintenance are important.

Is this answer helpful?

A

Yes. The bungee cord degrades under UV exposure. Inspect it regularly for signs of wear or damage and replace it promptly to ensure reliable mounting and safety.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Lightweight double-hinged quick-release fits aero and conventional forks
  • Adjustable longitudinal slots ensure a consistent 1.5 cm clearance
  • Compatible with tyres up to 38 mm—good for road, gravel and cyclocross
  • Option for permanent mounting with cable ties for theft deterrence
  • Supplied paint protection film helps prevent frame damage
VS

Disadvantages

  • Maximum tyre width limited to 38 mm, not suitable for wider gravel tyres
  • Bungee cords subject to UV ageing—require periodic inspection and replacement
  • Screws must be tightened to max 1 Nm; overtightening risks damage
  • Permanent cable-tie mounting is irreversible and may mark frame
  • SKS disclaims responsibility for paint or carbon damage from use
M: OA-GPT-5-NAN

Product Specification

Type

Front wheel

Colors

black

Wheel size

28"

Tire width max.

1.50 in

Weight

0.20 lb

M: OA-GPT-54-NAN

Product Description

SKS S-Board Schutzblech Manual

The SKS S-Board is a lightweight clip-on front mudguard designed for road, all-road, cyclocross, hybrid and gravel bikes, accommodating tyres up to 38 mm wide. Engineered in Germany, it pairs well with the S-BLADE rear mudguard to provide coordinated splash protection without disrupting bike handling or aerodynamics. Its double-hinged quick-release fitting and slim profile allow mounting on modern aero forks and many conventional fork shapes.

Key features and usage

The S-Board uses a bungee cord quick-release system combined with longitudinal adjustment slots to fine-tune wheel clearance. When mounted, maintain a minimum 1.5 cm clearance between the mudguard and tyre all around to avoid contact that could cause damage or a crash. Screws that secure the guard must be tightened gently — maximum torque 1 Nm — to protect components and maintain proper positioning. The guard can be temporarily attached with the quick-release bungee or permanently fixed using cable ties for theft protection and extra security.

Installation overview

Position the mudguard on the fork so the top section meets the 1.5 cm clearance. Wrap the quick-release bungee around the fork and hook it into place; use the included paintwork protection film if needed. Adjust longitudinally via the elongated slots to ensure uniform clearance, then retighten screws to the specified 1 Nm. Trim any excess bungee cord so loose ends cannot touch spokes. For permanent mounting, add two cable ties per side in addition to the bungee cord, pull tight and trim excess tie tails.

Safety and maintenance

Always check clearance before every ride and verify brakes operate correctly without interference from the mudguard. Bungee cords degrade over time from UV exposure; inspect them regularly and replace at the first sign of wear. Use the supplied paint protection film and clean attachment points to reduce risk of frame paint damage. SKS disclaims responsibility for paint or carbon damage resulting from product use, so careful installation and upkeep are essential.

Notes

  • Maximum tyre width: 38 mm.
  • Maximum screw torque: 1 Nm (use a 2.5 mm Allen key).
  • Use paint protection film to avoid frame marks.
  • There is a YouTube mounting video available for visual guidance.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly