Manual.ly Logo

sera marin stream pump SPM 8000 Manual

0.0 · 0 Ratings

PDF manual · 41 Pages

English

M: gpt-5.6-terra
page

/ 41

Loading...
4aa93af2984da5ee34985a72605145cc11e8 page 7
7
The sera marin stream pump SPM 8000 is designed for
use in aquariums whose inhabitants are exposed to per-
manent currents in their natural biotopes. Many marine in-
habitants have optimally adapted to these conditions.
Sessile animals are supplied with nutrients only by water
currents. Insufcient currents may affect sufcient nutrient
supply of these animals. The currents generated by normal
lter pumps are often not sufcient for marine aquariums.
It is therefore advisable to install one or several additional
sera marin stream pumps SPM 8000.
SAFETY PRECAUTION
All electrical units must be disconnected from the mains/
power supply before conducting work at the sera marin
stream pump SPM 8000 or the aquarium.
Application and application range
The sera marin stream pump SPM 8000 can be used in
aquariums between approx. 100 l (25 US gal.) up to 500 l
(132 US gal.). Several pumps may be used in larger tanks.
Due to the large intake openings, the sera marin stream
pump SPM 8000 should not be used in tanks with sh fry
or very small sh. The clamping lever suction cup allows
attaching the sera marin stream pump SPM 8000 to the
aquarium glass almost everywhere.
Kit includes
sera marin stream pump SPM 8000
Clamping lever suction cup with ball joint holder
Parts list (1)
1.1
Motor block
1.2 Rotor, ceramic shaft with rubber bearings
1.3 Outlet nozzle
1.4 Back part with cast-in holder screw
1.5 Clamping lever suction cup with ball joint holder
Assembly instruction (2 – 7)
Attachment with the clamping lever suction cup
The included clamping lever suction cup allows particular-
ly strong xation at the aquarium glass which cannot be
achieved with ordinary standing feet. Thoroughly remove
algae and dirt from the desired location for positioning the
clamping lever suction cup.
Screw the ow pump into the ball joint holder of the clamp-
ing lever suction cup (2).
Take the sera marin stream pump SPM 8000, fold the
clamping lever upwards and pull it out of the suction cup
casing (3). Position the sera marin stream pump SPM
8000 in the desired location (4). Press the rubber of the
clamping lever suction cup against the glass while the
clamping lever is still up (5). Then move the clamping lever
(6). You will need to repeat the process in case the clamp-
ing lever can be moved without resistance. Check whether
the clamping lever suction cup is rmly attached to the
aquarium glass. No invertebrates should be located direct-
ly in front of the nozzle of the sera marin stream pump
SPM 8000 (7).
Operation
Plug the mains plug into the main socket after the pump
has been installed. The sera marin stream pump SPM
8000 begins to run immediately. Watch the sera marin
stream pump SPM 8000 for a while as to see whether in-
vertebrates are being exposed to currents too strong, or if
they even are about to being torn off. Immediately pull the
mains plug in this case and switch off the sera marin
stream pump SPM 8000 by doing so. Re-adjust the outlet
direction of the sera marin stream pump SPM 8000 (2). If
applicable, move invertebrates which are exposed to very
strong currents.
Due to the strong currents, especially directly in front of the
nozzle, the water level may rise in case of being directed
against the aquarium glass. The water level should be low-
ered before starting the pump, and slowly be topped up
again when the sera marin stream pump SPM 8000 is
running.
Cleaning
Take the sera marin stream pump SPM 8000 out of
the aquarium for cleaning and clean it under running water
with a dishwashing brush or a sponge. Do not use any
detergents. Place the pump in a descaler solution if the
casing is lime encrusted. Please adhere to the information
for use of the descaler solution. Rinse off the descaler so-
lution very carefully. Then remove partially dissolved
lime remainders under running water using a brush or a
sponge.
Pull the current nozzle (1.3) off the motor part (1.1) for re-
moving parts drawn into the pump, and clean both parts.
Be sure to locate the shaft properly in its bearings when re-
assembling the unit.

Information for use
sera marin stream pump SPM 8000

information for use is also to be handed over.
GBI marin stream pump_8_2012neu.indd 9 17.08.2012 13:58:29

Chat with your sera marin stream pump SPM 8000 manual using AI

Get instant AI answers from your sera marin stream pump SPM 8000 manual

Ask anything about the sera marin stream pump SPM 8000. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend marin stream pump SPM 8000?

Yes No

Frequently Asked Questions

A

The pump is designed for aquariums from approximately 100 to 500 liters. In larger aquariums, multiple units can be installed to improve circulation coverage and create more varied water movement.

Is this answer helpful?

A

The sera marin stream pump SPM 8000 delivers approximately 8,000 liters per hour. This high output is intended to supplement normal filtration flow in marine aquariums.

Is this answer helpful?

A

It should not be used in tanks containing fry or very small fish. The intake openings are relatively large, which can create a risk for small livestock.

Is this answer helpful?

A

It uses a clamping-lever suction cup with a ball-joint holder. Clean algae and dirt from the glass before mounting, then check that the suction cup is firmly secured.

Is this answer helpful?

A

Remove it from the aquarium and rinse it under running water using a brush or sponge. Do not use detergents. For heavy lime deposits, use a suitable descaling solution and rinse the pump thoroughly afterward.

Is this answer helpful?

A

If cleaning does not restore performance, replace the rotor and ceramic shaft. The rubber bearings should also be replaced when the ceramic shaft is changed.

Is this answer helpful?

M: gpt-5.6-terra

Advantages and Disadvantages

Advantages

  • Provides approximately 8,000 l/h of circulation for strong marine aquarium water movement.
  • Suitable for aquariums of about 100 to 500 liters, with multiple pumps supported for larger tanks.
  • Ball-joint holder and clamping-lever suction cup allow secure placement and adjustable flow direction.
  • Ceramic shaft, rotor, rubber bearings, and mounting suction cup are available as replacement parts.
  • IPX8 rating supports submerged use up to 1 m, with water temperatures up to 40 C.
VS

Disadvantages

  • Large intake openings make it unsuitable for tanks containing fry or very small fish.
  • Strong flow can stress or dislodge invertebrates if the outlet is aimed poorly.
  • Requires regular cleaning and occasional descaling to maintain circulation performance.
  • Designed for 220-240 V, 50 Hz electrical systems.
  • A damaged power cable means the pump must no longer be used.
M: gpt-5.6-terra

Product Specification

Type

Flow pump

Suitable for

Freshwater, saltwater, aquariums

Flow rate

2,113.38 gal/h

Filter circulation

N/A

Net pump head

N/A

Aquarium size

Up to approx. 211.34 gal

Filtration

N/A

Connections

N/A

Power consumption

28 W

Dimensions

3.31 x 3.31 x 3.78 in (W x H x D)

Special features

Suction cup mount, 4.59 ft cable length

Manufacturer warranty

Two years

M: gpt-5.6-terra

Product Description

sera marin stream pump SPM 8000 Aquarium Circulation Pump

The sera marin stream pump SPM 8000 Aquarium circulation pump is designed to create the strong, continuous water movement that many marine aquarium inhabitants need. In reef and saltwater habitats, water flow helps distribute oxygen and nutrients, especially to sessile animals such as corals and other invertebrates. Standard filter pumps may not provide enough circulation on their own, making this stream pump a useful addition for building a healthier, more dynamic aquarium environment.

With an approximate circulation capacity of 8,000 liters per hour, the SPM 8000 delivers substantial flow for aquariums from around 100 to 500 liters. Larger aquariums can use multiple pumps to create broader, more natural current patterns. Its directional outlet nozzle and ball-joint mounting system make it easier to aim the flow where it is most beneficial, whether that means improving circulation behind rockwork or supporting water movement across a reef layout.

Secure Positioning and Adjustable Flow Direction

The pump includes a clamping-lever suction cup with a ball-joint holder. This mounting method is intended to provide a firmer grip on clean aquarium glass than ordinary suction cups. Before installation, algae and debris should be removed from the chosen area to ensure reliable attachment. Once positioned, the adjustable holder allows the outlet direction to be refined after observing how the current affects fish, corals, and other aquarium residents.

Because the flow is powerful close to the nozzle, care is important during setup. Invertebrates should not be placed directly in front of the outlet, and the pump should be monitored after startup. If animals are exposed to excessive current, reposition the pump or move the affected livestock. When directing flow toward aquarium glass, the water level may rise locally, so filling and water-level management should be handled gradually.

Maintenance and Safe Use

Routine cleaning helps preserve flow performance. Remove the pump from the aquarium, rinse it under running water, and use a soft brush or sponge to remove debris. Detergents should not be used. For heavy lime buildup, an appropriate descaling solution may be used, followed by very thorough rinsing. If performance remains reduced after cleaning, the rotor, ceramic shaft, and rubber bearings may need replacement.

The sera marin stream pump SPM 8000 operates at 220-240 V, 50 Hz, uses 28 W, and has a 1.4 m cable. It is rated IPX8 for use underwater up to 1 m and is suitable for water temperatures up to 40 C.

Notes

  • Disconnect all electrical equipment before servicing the pump or aquarium.
  • Do not use this pump with fry or very small fish because of its large intake openings.
  • Use an RCD or FI safety switch with a maximum 30 mA trip current.
M: gpt-5.6-terra

© Copyright 2026 Manual.ly