Manual.ly Logo

sera flore CO2 Active Reactor 500 Manual

0.0 · 0 Ratings

PDF manual · 52 Pages

English

M: qwen/qwen3.5-flash-20260224
page

/ 52

Loading...
d227a4fe22a9b8782385f8ce681c906d37d5 page 8
8
The new sera flore CO
2
active reactors 500 and 1000 with
twin rotor supersede the generation of static CO
2
reac-
tors. The rotors, the upper one of which is designed as
a lamella rotor (6.3), ensure strong blending of CO
2
with
the aquarium water, allowing to dissolve several hun-
dred CO
2
bubbles per minute.
General notes
Dissolving CO
2
correctly and in sufficient amounts in
freshwater aquariums is the key to good and lasting
plant growth, especially in larger aquariums.
Added CO
2
that is only partially dissolved will escape via
the water surface in smallest bubbles and does not
reach the plants where it is actually required. The sera
active reactors are designed for optimized currents,
provide excellent performance capacity and can com-
pletely dissolve even large amounts of CO
2
. They can en-
tirely be disassembled, and are therefore easy to main-
tain and clean.
Safety advice for your fishkeeping
CO
2
lowers the pH value of the aquarium water.
Therefore be sure to monitor the pH value when using
the sera active reactors. We recommend the seramic
pH Controller to do so for professionals, or the sera CO
2
long-term indicator and the sera pH-Test kit for begin-
ners.
Application range
The sera flore CO
2
active reactor 500 is suitable for
freshwater aquariums between 250 l (66 US gal.) and 600 l
(159 US gal.). We recommend the sera flore CO
2
active
reactor 1000 for larger or densely planted aquariums.
Both reactors are identically constructed. Their only dif-
ference is the volume of the lower reactor part (6.6).
Usage and function
The sera flore CO
2
active reactors 500 and 1000 can be
integrated into an existing filter circuit outside the
aquarium (fig. 1). They can also be operated within (fig.
2) or outside (fig. 3) the aquarium with a feed pump, e.g.
sera P 700 for the sera flore CO
2
active reactor 500 or
sera P 1200 for the sera flore CO
2
active reactor 1000.
Recommended pump performance:
• for sera flore CO
2
active reactor 500
at least 500 l/h (132 US gal.)
• for sera flore CO
2
active reactor 1000
at least 700 l/h (185 US gal.)
The water current (4.1) of the pump drives the double
rotor (4.2) integrated in the reactor, which disperses CO
2
introduced from the pressure gas bottle (4.3) so finely
that it entirely dissolves in water. Even large amounts of
CO
2
can be dissolved entirely if required, allowing to
supply even large, densely planted aquariums with CO
2
economically.
We emphasize once again that CO
2
overdosage may
cause fish loss. The performance capacity of the reactor
is sufficient to create a pH value of 5.9 if the unit is op-
erated without limiting. The setting of the fine-adjust-
ment needle valve of a pressure reducer must not
change. Be sure to use a high quality fine-adjustment
needle valve in the pressure operating equipment as to
avoid too much CO
2
getting into the reactor.
Kit includes (fig. 5)
5.1 sera flore CO
2
active reactor 500 or 1000
5.2 Holder plate
5.3 2 suction cups
Parts list (fig. 6)
6.1 Reactor head with hose connectors for
6.1.1 Water intake
6.1.2 Water outlet
6.1.3 CO
2
intake connector
6.1.4 3 union nuts
6.2 O-ring seal
6.3 Lamella rotor
6.4 Blade rotor
6.5 Standpipe
6.6 Lower reactor part with screw thread and stand-
pipe guiding
6.7 Holder plate
Accessories (not included)
sera flore CO
2
bubble counter (item No. 08059)
sera non-return valve (item No. 08818)
Hose, 16 mm (5/8 in.) internal diameter
sera CO
2
hose (item No. 08022)
Attachment screws for holder plate
Assembly instruction and operation
Installation outside the aquarium into the circuit of an
external filter (fig. 1)
(e.g. sera fil bioactive 400 + UV external filter)
Switch off the present external filter for installing the
sera flore CO
2
active reactor and empty the attached
hoses. Cut the hose that directs the water cleaned by
the filter back into the aquarium in a suitable position.
Hang up the sera flore CO
2
active reactor 500 or 1000 in
a position that allows to lay all hoses free from kinks and
without much tension. Install the holder of the sera ac-
tive reactor 500 or 1000 (5.2) vertically, allowing to hang
up the reactor vertically as well (1.1). You can attach the
holder plate with screws instead of the suction cups.
Connect the filter outlet hose piece to the intake of the
reactor (1.2), and the hose directing the water into the
aquarium to the water outlet of the reactor (1.3). Secure
the hoses to the water intake and outlet of the reactor
using the union nuts. Now push the CO
2
supplying hose
4/6 mm (preferably use the CO
2
proof sera CO
2
hose for
this purpose) onto the CO
2
intake connector (1.4). A
bubble counter (1.5) should be integrated into the CO
2
US
Information for use
sera flore CO
2
active reactor 500 and 1000
Please read these instructions carefully and keep for future use.
sera flore Reaktoren_GBI INT:GBI seramic 15.01.10 11:55 Seite 7

Chat with your sera flore CO2 Active Reactor 500 manual using AI

Get instant AI answers from your sera flore CO2 Active Reactor 500 manual

Ask anything about the sera flore CO2 Active Reactor 500. Answers come from this manual, with the pages they are based on.

flore CO2 Active Reactor 500 Maintenance Schedule

After several disassemblies
Replace O-ring seal

Change the O-ring (6.2) after the unit has been disassembled multiple times to ensure a proper seal.

After long operation
Inspect and replace rotors

Check the lamella rotor (6.3) and blade rotor (6.4) for wear after extended use and replace them if necessary.

M: QW-35-FL

Ask a Question

0/1000

Do you recommend flore CO2 Active Reactor 500?

Yes No

Frequently Asked Questions

A

The 500 model works for 250 to 600 liters. The 1000 model is recommended for larger or heavily planted tanks. Both are construction identical except for volume.

Is this answer helpful?

A

Install within filter circuits, inside the tank, or outside. Use recommended pumps. Connect hoses securely and ensure no air remains inside during setup.

Is this answer helpful?

A

Yes, if CO2 levels are managed to prevent pH drops. Monitor pH with test kits or controllers regularly for safety.

Is this answer helpful?

A

Disassemble parts and clean without detergent. Replace worn O-rings or rotors when necessary to maintain performance.

Is this answer helpful?

A

Minimum 500 liters per hour for the 500 model. The 1000 model requires at least 700 liters per hour pump capacity.

Is this answer helpful?

A

No. Operating pressure must not exceed one bar. Use a high-quality pressure reducer with a needle valve.

Is this answer helpful?

A

O-rings, rotor sets, suction cups, and holder plates are available as spare parts for both models.

Is this answer helpful?

M: qwen/qwen3.5-flash-20260224

Advantages and Disadvantages

Advantages

  • Innovative double rotor technology for efficient gas solution.
  • Fully disassemblable design allows easy cleaning and maintenance.
  • High capacity suitable for large and densely planted aquariums.
  • Versatile installation inside, outside, or in filter circuits.
  • Reduces CO2 waste by dissolving hundreds of bubbles per minute.
VS

Disadvantages

  • Requires external pump for some installation configurations.
  • Needs regular pH monitoring due to gas lowering effects.
  • O-rings and rotors require replacement after long-term use.
  • Specific pressure limits must not be exceeded to prevent damage.
  • Accessories like bubble counters and hoses are sold separately.
M: qwen/qwen3.5-flash-20260224

Product Specification

Application

CO2 Supply, Plant Fertilization

Type

CO2 Reactor, CO2 Injection

Specifications

0.63/0.87 inch Hose Connection

Suitability

Freshwater, 66.04-158.50 gallons

Power Consumption

N/A

M: qwen/qwen3.5-flash-20260224

Product Description

Enhancing Plant Growth with Advanced CO2 Technology

Achieving robust aquarium plant health requires precise carbon dioxide management. The sera flore CO2 Active Reactor 500 and 1000 utilize innovative double rotor technology to ensure lossless CO2 dissolution. This system replaces older static reactor generations by offering superior performance for freshwater setups. Whether you own a small tank or a massive planted aquarium, understanding your equipment is vital. Referencing a comprehensive sera flora CO2 500 Active Reactor Manual ensures you maximize efficiency and safety during setup.

Innovative Design for Maximum Efficiency

The core innovation lies in the twin rotor system. The upper lamella rotor and lower blade rotor work together to break down CO2 gas into microscopic bubbles. This process allows several hundred bubbles to dissolve per minute effectively. Water flow drives the rotors internally, creating strong mixing without external energy. This ensures that even large quantities of gas are completely absorbed before reaching plant roots. Partial dissolution leads to wasted gas escaping at the surface, a problem this reactor solves. The reactors are fully disassemblable, making maintenance straightforward.

Flexible Installation Options

Versatility defines this equipment. You can integrate the unit into an existing external filter circuit or operate it inside the aquarium. Outside aquarium installation with a circulation pump is another valid method. Recommended pump power varies by model, requiring at least 500 l/h for the smaller unit and 700 l/h for the larger one. Proper hose selection is crucial to avoid restrictions. Always secure connections tightly to prevent leaks or air pockets. Including a bubble counter allows accurate tracking of dosage levels.

Maintenance and Safety Protocols

Regular upkeep keeps the reactor functioning optimally. The design allows complete disassembly for cleaning parts without detergents. Rotors and O-rings may wear over time and require replacement as spare parts. Safety is paramount since CO2 lowers pH levels. You must regularly monitor water chemistry. Use a quality pressure reducer to maintain pressure below one bar. Never bypass safety valves to prevent accidents. A non-return valve protects equipment from water backflow. By following guidelines, you ensure a healthy environment for fish and plants alike.

Suitability for Various Tank Sizes

The 500 model suits tanks between 250 and 600 liters. Larger or densely planted environments benefit from the 1000 version. Both share identical construction but differ in volume. This flexibility allows hobbyists to scale their systems easily. Ensure your pressure reducer has a needle valve for precise adjustments. Consistent delivery ensures plants receive nutrients without toxicity risks.

M: qwen/qwen3.5-flash-20260224

© Copyright 2026 Manual.ly