Manual.ly Logo

Schneider Electric Wiser Manual

0.0 · 0 Ratings

PDF manual · 2 Pages

English

M: OA-GPT-5-NAN
page

/ 2

Loading...
f0692e2ec0721a6d2c56d69bd2fa570ed72d page 1
Ø 1 mm
(2)
(1)
a.
×7
A
b.
(3)
PULL
TO
ACTIVATE
PULL
TO
ACTIVATE
en, ...
A B D
F
C
E
GH
en
Wiser Window/Door Sensor
About this product
The Wiser Window/door sensor (hereinafter referred
to as sensor) consists of two separate parts: primary
and secondary. The primary part includes the
sensing circuit which detects the secondary part. The
secondary part is a magnet.
When the sensor is connected to the Wiser Hub and
the window/door is opened or closed, the primary part
directly reports the change to the hub.
1 Package contents
A Primary part (sensing circuit)
B Secondary part (magnet)
C Base plate
D Adhesive pad
E Screws: 2 × ST2 × 10 mm, 1 × M2 × 3 mm
F Installation instructions
2 Choose suitable location to install
G Vertical mounting options
H Horizontal mounting options
3 Installing the sensor
NOTICE
EQUIPMENT DAMAGE
• To avoid degrading sensor performance, do not
install the sensor near magnetic devices.
• With the window/door in the closed state, the
distance between the primary part and secondary
part of the sensor should be <18 mm for a
non-metallic base (for example, wood or plastic
surfaces) and <10 mm for a metallic base.
Failure to follow these instructions can result in
equipment damage.
CCT591012
!
„
§
$
da
Wiser trådløs dør og vindue
kontaktsæt
Om dette produkt
Wiser trådløs dør og vindue kontaktsæt (herefter
kaldet sensor) består af to separate dele: primær og
sekundær. Primærdelen omfatter registreringskredsen,
som detekterer den sekundære del. Den sekundære
del er en magnet.
Når sensoren er tilsluttet Wiser Hub, og vinduet/døren
åbnes eller lukkes, melder den primære del ændringen
direkte til Hub.
1 Pakkens indhold
A Primær del (registreringskredsløb)
B Sekundær del (magnet)
C Baseplade
D Klæbepude
E Skruer: 2 × ST2 × 10 mm, 1 × M2 × 3 mm
F Installationsvejledning
2 Vælg et passende sted at installere
G Vertikale monteringsmuligheder
H Horisontale monteringsmuligheder
3 Installation af sensor
BEMÆRK
SKADE PÅ UDSTYR
• Installér ikke føleren i nærheden af magnetiske
enheder for at undgå forringet sensorydeevne.
• Med vinduet/døren i lukket tilstand skal afstanden
mellem følerens primære og sekundære del
være < 18 mm for en ikke-metallisk sokkel (f.eks.
træ- eller plastikoverader) og < 10 mm for en
metallisk sokkel.
Manglende overholdelse af disse anvisninger
kan medføre skader på udstyret.
(1) Fjern batteriets isoleringsstrimmel
A Lysdiode blinker grønt
(2) Monter bundpladen
a. Montering med klæbepuder
Brug klæbepuder på træ- eller plastikoverader eller
metaloverader.
BEMÆRK: Brug kun klæbepuder på metaloverader.
b. Montering med skruer
• Brug skruerne på træ- eller plastikoverader.
• Forbor et hul på 1 mm, hvis der anvendes skruer.
(3) Monter føleren på basen.
4 Læs hele vejledningen online
Scan QR-koden, og vælg dit sprog for at få alle
oplysninger om enheden, herunder drift, konguration
og brug af produktet med et Wiser-system.
Tekniske data
Batteri 3 VDC, CR2450
Batteriets levetid
Op til 5 år (kan variere
afhængigt af brug, hyppighed
af rmwareopdatering og miljø)
Nominel e󰀨ekt ≤90 mW
IP-beskyttelse IP20
Betriebsfrequenz 2405 - 2480 MHz
Maks. transmitteret
radiofrekvense󰀨ekt
≤7 dBm
Driftstemperatur -10 °C til 50 °C
Relativ luftfugtighed 10 % til 95 %
Dimensioner for primær del
(H × W × D)
50,3 × 33 × 16,3 mm
Dimensioner for sekundær del
(H × W × D)
50 × 9 × 9 mm
Kommunikationsprotokol Zigbee 3.0-certiceret
Varemærker
• Wiser™ er et varemærke og tilhører Schneider
Electric A/S, dets datterselskaber og associerede
selskaber.
• Zigbee
®
er et registreret varemærke tilhørende
Connectivity Standard Alliance.
Andre varemærker og registrerede varemærker er
deres relevante ejeres egenskaber.
EU-overensstemmelseserklæring
Schneider Electric Danmark A/S erklærer hermed,
at dette produkt er i overensstemmelse med de
væsentlige krav og andre relevante bestemmelser
i DIREKTIV 2014/53/EU OM RADIOUDSTYR.
Overensstemmelseserklæringen kan downloades på:
se.com/docs.
Schneider Electric Danmark A/S
Lautrupvang 1, 2750 Ballerup
Phone: +45 88 30 20 00
www.lk.dk
da esen de
(1) Remove the battery isolation strip
A LED ashes green
(2) Mount the base plate
a. Mounting using adhesive pads
For wood or plastic surfaces or metal surfaces, use the
adhesive pads.
Note: For metal surfaces, use the adhesive pads only.
b. Mounting using screws
• For wood or plastic surfaces, use the screws.
• If using screws, pre-drill a 1 mm hole.
(3) Mount the sensor on the base plate.
4 Read full device guide online
Scan the QR code and choose your language
for complete information about the device, including
operation, conguration and using the product with a
Wiser system.
Technical data
Battery 3 VDC, CR2450
Battery life
Up to 5 years (may vary based
on the usage, frequency of
rmware update and
environment)
Nominal power ≤90 mW
IP rating IP20
Operating frequency 2405 - 2480 MHz
Max. radio frequency power
transmitted
≤7 dBm
Operating temperature -10 °C to 50 °C
Relative humidity 10 % to 95 %
Primary part dimensions
(H × W × D)
50.3 × 33 × 16.3 mm
Secondary part dimensions
(H × W × D)
50 × 9 × 9 mm
Communication protocol Zigbee 3.0 certied
Trademarks
• Wiser™ is a trademark and the property of
Schneider Electric SE, its subsidiaries and a󰀩liated
companies.
• Zigbee
®
is a registered trademark of the
Connectivity Standard Alliance.
Other brands and registered trademarks are properties
of their relevant owners.
EU Declaration of Conformity
Hereby, Schneider Electric Industries, declares
that this product is in compliance with the essential
requirements and other relevant provisions of RADIO
EQUIPMENT DIRECTIVE 2014/53/EU. Declaration of
conformity can be downloaded on: se.com/docs.
Schneider Electric Industries SAS
If you have technical questions, please contact the
Customer Care Centre in your country.
se.com/contact
de
Wiser Fenster-/Türsensor
Über dieses Produkt
Der Wiser Fenster-/Türsensor (nachstehend Sensor
genannt) besteht aus zwei separaten Elementen:
primär und sekundär. Das Primärelement enthält den
Sensorschaltkreis, der das Sekundärelement erkennt.
Das Sekundärelement ist ein Magnet.
Wenn der Sensor mit dem Wiser Hub verbunden ist
und das Fenster/die Tür geö󰀨net oder geschlossen
wird, informiert das Primärelement den Hub direkt über
diese Veränderung.
1 Inhalt des Pakets
A Primärelement (Sensorschaltkreis)
B Sekundärelement (Magnet)
C Basisplatte
D Klebepad
E Schrauben: 2 × ST2 × 10 mm, 1 × M2 × 3 mm
F Installationsanweisungen
2 Geeigneten Installationsort auswählen
G Optionen für vertikale Montage
H Optionen für horizontale Montage
es
Sensor de ventana/puerta
Wiser
Acerca de este producto
El sensor de ventana/puerta Wiser (en adelante
denominado sensor) consta de dos partes
independientes: primaria y secundaria. La parte
primaria incluye el circuito de detección que detecta la
parte secundaria. La parte secundaria es un imán.
Cuando el sensor está conectado a la Wiser Hub y
la ventana/puerta están abiertas o cerradas, la parte
primaria informa directamente del cambio a la Wiser
Hub.
1 Contenido del paquete
A Parte primaria (circuito de detección)
B Parte secundaria (imán)
C Placa base
D Almohadilla adhesiva
E Tornillos: 2 × ST2 × 10 mm, 1 × M2 × 3 mm
F Instrucciones de instalación
2 Elija una ubicación adecuada para instalar
G Opciones de montaje en vertical
H Opciones de montaje en horizontal
3 Instalación del sensor
AVISO
DAÑOS EN EL EQUIPO
• Para evitar degradar el rendimiento del sensor,
no instale el sensor cerca de dispositivos
magnéticos.
• Con la ventana/puerta cerrada, la distancia entre
la parte primaria y la parte secundaria del sensor
debe ser <18 mm para una base no metálica
(por ejemplo, supercies de madera o plástico) y
<10 mm para una base metálica.
Si no se siguen estas instrucciones, el
dispositivo podría resultar dañado.
(1) Retire la banda aislante de la batería
A El LED parpadea en verde
Montaje de la placa base
a. Montaje con almohadillas adhesivas
Para supercies de madera, plástico o metal, use las
almohadillas adhesivas.
NOTA: Para supercies metálicas, utilice las
almohadillas adhesivas exclusivamente.
b. Montaje con tornillos
• Para supercies de madera o plástico, use los
tornillos.
• Si utiliza tornillos, realice oricios previos de 1mm
de diámetro.
(2) Monte el sensor en la placa base.
3 Einbau des Sensors
HINWEIS
BESCHÄDIGUNG DES GERÄTES
• Um eine Beeinträchtigung der Sensorleistung zu
vermeiden, darf der Sensor nicht in der Nähe von
Magnetgeräten installiert werden.
• Bei geschlossenem Fenster/geschlossener Tür
sollte der Abstand zwischen dem Primärelement
und dem Sekundärelement des Sensors <18 mm
bei einer nichtmetallischen Basis (z. B. Holz- oder
Kunststo󰀨oberächen) bzw. <10 mm bei einer
Metallbasis sein.
Die Nichtbeachtung dieser Anweisungen kann
zu Schäden am Gerät führen.
(1) Isolierungsstreifen der Batterie entfernen
A LED blinkt grün
(2) Basisplatte anbringen
a. Montage mit Klebepads
Für Oberächen aus Holz, Kunststo󰀨 oder Metall sind
die Klebepads zu verwenden.
HINWEIS: Für Oberächen aus Metall dürfen nur die
Klebepads verwendet werden.
b. Montage mit Schrauben
• Für Oberächen aus Holz oder Kunststo󰀨 sind
die Schrauben zu verwenden.
• Werden Schrauben verwendet, ein 1 mm Loch
vorbohren.
(3) Sensor auf der Basisplatte montieren.
4 Vollständiges Handbuch zum Gerät online
lesen
Den QR-Code scannen und die gewünschte
Sprache auswählen, um ausführliche Angaben zum
Gerät (z. B. Betrieb, Konguration und Einsatz des
Produkts mit einer Wiser Anlage) zu erhalten.
Technische Daten
Batterie 3 VDC, CR2450
Lebensdauer der Batterie
Bis zu 5 Jahre (kann je nach
Nutzung, Häugkeit des
Firmware-Updates und
Umgebung variieren)
Nennleistung ≤ 90 mW
Schutzart IP20
Betriebsfrequenz 2405-2480 MHz
Max. übertragene
Funkfrequenzleistung
≤ 7 dBm
Betriebstemperatur -10 bis 50 °C
Relative Luftfeuchtigkeit 10 % bis 95 %
Abmessungen des
Primärelements (H × B × T)
50,3 × 33 × 16,3 mm
Abmessungen des
Sekundärelements (H × B × T)
50 × 9 × 9 mm
Kommunikationsprotokoll Zigbee 3.0-zertiziert
Markennamen
• Wiser™ ist eine Marke und Eigentum von Schneider
Electric SE, Tochtergesellschaften und verbundenen
Unternehmen.
• Zigbee
®
ist eine eingetragene Marke der
Connectivity Standard Alliance.
Andere Marken und eingetragene Marken sind
Eigentum der jeweiligen Inhaber.
EU-Konformitätserklärung
Schneider Electric Industries erklärt hiermit, dass
dieses Produkt die grundlegenden Anforderungen
sowie anderen relevanten Bestimmungen der
FUNKANLAGEN-RICHTLINIE 2014/53/EU erfüllt. Die
Konformitätserklärung kann heruntergeladen werden
unter: se.com/docs.
Schneider Electric Industries SAS
Bei technischen Fragen wenden Sie sich bitte an das
Customer Care Center in Ihrem Land.
se.com/contact
fr hu sv svpt
À DÉPOSER À DÉPOSER
EN MAGASIN EN DÉCHÈTERIE
OU
Points de collecte sur www.quefairedemesdechets.fr
FR
Privilégiez la réparaon ou le don de votre appareil !
Cet appareil,
ses accessoires
et baerie se
recyclent
JYT54995-03 09/2023

Chat with your Schneider Electric Wiser manual using AI

Get instant AI answers from your Schneider Electric Wiser manual

Ask anything about the Schneider Electric Wiser. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Wiser?

Yes No

Frequently Asked Questions

A

The Wiser Door/Window Sensor is a two-part magnetic contact sensor (primary sensing unit and secondary magnet) that detects door or window open/close events and reports them to a Wiser Hub over Zigbee 3.0 for smart home automation and security.

Is this answer helpful?

A

Remove the battery isolation strip, mount the base plate using adhesive pads (recommended for metal) or screws (pre-drill a 1 mm hole for wood/plastic), attach the sensor to the base plate, and pair it with your Wiser Hub following on-screen or QR-code instructions.

Is this answer helpful?

A

The sensor uses a CR2450 3 V battery. Battery life is advertised up to 5 years but can vary depending on usage, firmware update frequency, and environmental factors.

Is this answer helpful?

A

Yes. Keep the primary and secondary parts within 18 mm on non-metallic surfaces and within 10 mm on metallic surfaces. Do not install near other magnetic devices to avoid degraded sensor performance.

Is this answer helpful?

A

No. The sensor has an IP20 rating, which means it is intended for indoor use only and is not protected against water or heavy dust exposure—install it in dry, sheltered locations.

Is this answer helpful?

A

The sensor is Zigbee 3.0 certified, operating at 2405–2480 MHz with a maximum transmitted RF power of ≤7 dBm, enabling integration with Zigbee-compatible hubs and ecosystems.

Is this answer helpful?

A

Verify correct gap between the primary and secondary parts based on surface type, ensure the sensor is not near magnetic interference, confirm Zigbee network range and hub connectivity, and check battery health and firmware status via the Wiser system.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Compact two-piece design for discreet mounting on doors and windows
  • Zigbee 3.0 certification for broad smart home compatibility and reliable communication
  • Long battery life (up to 5 years) using a common CR2450 3 V cell
  • Easy installation with adhesive pads or screws and simple pairing to Wiser Hub
  • Low power consumption and wide operating temperature range (-10 °C to 50 °C)
VS

Disadvantages

  • IP20 rating limits use to indoor, dry locations
  • Performance can degrade near other magnetic devices
  • Requires Zigbee-compatible hub (Wiser Hub recommended) for full functionality
  • Magnet-to-sensor gap requirements may complicate installation on some metal frames
  • Limited RF power and range compared with some alternative wireless protocols
M: OA-GPT-5-NAN

Product Specification

Type

Sensor

Standard

ZigBee 3.0

Function

Opening/Closing Sensor

Dimensions

1.97x1.30x0.64in (Sensor), 1.97x0.35x0.35in (Contact)

Special features

IP20, battery-powered (1x CR2450), app-controlled

M: OA-GPT-54-NAN

Product Description

Schneider Electric Wiser Door/Window Sensor — Reliable Opening/Closing Detection

The Schneider Electric Wiser Door/Window Sensor is a compact two-piece magnetic contact sensor designed for smart home security and automation. Composed of a primary sensing module and a secondary magnet, the sensor detects when a door or window opens or closes and reports that state change to a Wiser Hub using Zigbee 3.0. Its small footprint and discreet profile make it suitable for a wide range of doors and windows, while the Zigbee certification ensures reliable integration with compatible smart home systems.

Installation is straightforward: remove the battery isolation strip, mount the base plate using adhesive pads or screws (pre-drill a 1 mm hole for screws on wood or plastic), attach the sensor to the base plate, and pair it with the Wiser Hub. For best performance, keep the primary and secondary parts within 18 mm on non-metallic surfaces and within 10 mm on metallic surfaces. Avoid installing the sensor near magnetic devices to prevent degraded performance.

Powered by a CR2450 3 V battery, the sensor offers up to five years of battery life depending on usage and environment. It operates on 2405–2480 MHz with a maximum transmitted RF power of ≤7 dBm, an IP20 rating, and a wide operating temperature range from -10 °C to 50 °C. The primary unit measures 50.3 × 33 × 16.3 mm and the magnet 50 × 9 × 9 mm, making the device suited for discreet mounting on many frame styles.

Because the device is certified to Zigbee 3.0 and complies with relevant EU radio equipment directives, it can be used reliably within compliant smart home ecosystems. Full configuration options and additional guidance are available via the product documentation online (scan the QR code supplied with the device for language-specific instructions and advanced setup tips).

Notes:

  • Use adhesive pads for metal surfaces; screws are recommended for wood/plastic when appropriate. Pre-drill 1 mm holes for screw mounting.
  • Maintain the specified gap between primary and secondary parts to avoid false readings or device damage.
  • Check compatibility with your Wiser Hub and Zigbee network before installation.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly