Manual.ly Logo

Schneider Electric EVlink Pro AC Pedestal Manual

0.0 · 0 Ratings

PDF manual · 16 Pages

English

M: QW-35-FL
page

/ 16

Loading...
dd1f04487dedba277c9b166b8cf395f1da13 page 2
MFR7099401 -02 2/16
© 2020 Schneider Electric - All rights reserved.
Content / Contenu / Inhalt / Innhold
This document must be kept for future
use.
IMPORTANT NOTE
• This accessory should be installed,
repaired and maintained only by qualied
personnel. No responsibility is assumed
by Schneider Electric for any
consequences arising out of the use of
this document.
• A qualied person is one who has skills
and knowledge related to the
construction, installation and operation of
electrical equipment and who has
received safety training to recognize and
avoid the hazards involved.
• Read this document carefully and
examine the accessory to become
familiar with its operation before installing
it.
• All applicable local, regional, and
national regulations must be respected
when installing, repairing, and
maintaining this accessory.
• This accessory should not be installed
if, when unpacking, you observe that it is
damaged.
• To simplify the illustrations, only the
power and earth wiring are shown in the
document.
Ce document doit être conservé pour une
utilisation future.
REMARQUE IMPORTANTE
• L’installation, la réparation et la
maintenance de cet accessoire doivent
être assurées uniquement par des
personnes qualiées. Schneider Electric
décline toute responsabilité quant aux
éventuelles conséquences découlant de
l’utilisation de ce document.
• Une personne qualiée est une
personne disposant de compétences et
de connaissances en matière de
construction, installation et
fonctionnement du matériel électrique et
ayant bénécié d’une formation de
sécurité an de percevoir et d’éviter les
dangers associés.
• Lisez attentivement ce document et
examinez l'accessoire pour vous
familiariser avec son fonctionnement
avant de faire son installation.
• Toutes les réglementations locales,
régionales et nationales applicables
doivent être respectées lors de
l’installation, réparation et maintenance
de cet accessoire.
• Cet accessoire ne doit pas être installé
si vous constatez lors du déballage qu'il
est endommagé.
• Pour simplier les illustrations, seuls
les câbles de d'alimentation et de terre
sont indiqués dans le document.
Bewahren Sie bitte dieses Dokument als
Referenz für den weiteren Gebrauch auf.
WICHTIGER HINWEIS
• Dieses Zubehör darf nur von
qualiziertem Fachpersonal installiert,
repariert und gewartet werden.
Schneider Electric haftet nicht für
Schäden, die durch die Verwendung
dieses Dokuments entstehen.
• Als Fachpersonal gelten Mitarbeiter,
die über Qualikationen und Kenntnisse
hinsichtlich der Konstruktion, der
Installation und des Betriebs elektrischer
Geräte verfügen und eine Schulung zur
Erkennung und Vermeidung möglicher
Gefahren absolviert haben.
• Lesen Sie sich dieses Dokument bitte
sorgfältig durch und machen Sie sich mit
dem Zubehör, dessen Betrieb und
Bedienung vertraut, bevor Sie mit der
Installation beginnen.
• Bei der Installation, Reparatur und
Wartung des Zubehörs sind alle
geltenden örtlichen, regionalen und
nationalen Regelungen und Vorschriften
einzuhalten.
• Installieren Sie das Zubehör nicht,
wenn Sie bei der Entnahme aus der
Verpackung Materialschäden feststellen
können.
• Zur Vereinfachung der Abbildungen
werden im Dokument nur die Strom- und
Erdungskabel angezeigt.
Dette dokumentet må beholdes for
fremtidig bruk.
VIKTIG!
• Dette tilbehøret må bare installeres,
repareres og vedlikeholdes av kvalisert
personell. Schneider Electric påtar seg
intet ansvar for eventuelle konsekvenser
av bruken av dette dokumentet.
• En kvalisert person er en som har
ferdigheter og kunnskaper relatert til
bygging, installasjon og bruk av elektrisk
utstyr, og som har gjennomgått
sikkerhetsopplæring for å se og unngå
farer som er involvert.
• Les dette dokumentet nøye og
undersøk tilbehøret for å gjøre deg kjent
med virkemåten før installering.
• Alle gjeldende lokale, regionale og
nasjonale bestemmelser må overholdes
ved installering, reparasjon og
vedlikehold av tilbehøret.
• Dette tilbehøret må ikke installeres hvis
du ser at det er skadet når du pakker det
ut.
• For å forenkle illustrasjonene vises
bare strøm- og jordledninger i
dokumentet.
1 Charging station accessory bag ref
EVA1PBS1
1 Sac d'accessoires pour station de
charge ref EVA1PBS1
1 Ladetank-Zubehörtasche Ref
EVA1PBS1
1 Ladestasjon tilbehørspose ref
EVA1PBS1
Bag for Instruction Sheet / Sac pour feuille d'instructions / Tasche für Anleitungsblatt /
Pose med dokumentasjon
1
Bag for fasteners / Sac pour attaches / Tasche für Befestigungselemente / Pose med festemateriell 1
Instruction Sheet (notice) / Instruction Sheet (notice) / Gebrauchsanweisung (Hinweis) / Instruksjonsark
(merknad)
1
Screw M5 x 20 torx / Vis M5 x 20 torx / Schraube M5 x 20 Torx / Skru M5 x 20 torx 2
Screw M5 x 10 torx / Vis M5 x 10 torx / Schraube M5 x 10 Torx / Skru M5 x 10 torx 2
Washer M5 / Rondelle M5/ Unterlegscheibe M5 / Skive M5 4
Ring tongue / Cosse à oeillet / Anschlussring / terminalring 1
Nut / Ecrou / Nuss / Lokk / nøtt 1
2 Charging station accessory bag ref
EVA1PBS2
2.Sac d'accessoires pour station de
charge ref EVA1PBS2
2 Ladetank-Zubehörtasche Ref
EVA1PBS2
2 Ladestasjon tilbehørsposer ref
EVA1PBS2
Bag for Instruction Sheet / Sac pour feuille d'instructions / Tasche für Anleitungsblatt /
Veske til instruksjonsark
1
Bag for fasteners / Sac pour attaches / Tasche für Befestigungselemente / Veske til fester 1
Instruction Sheet (notice) / Instruction Sheet (notice) / Gebrauchsanweisung (Hinweis) / Instruksjonsark
(merknad)
1
Screw M5 x 20 torx / Vis M5 x 20 torx / Schraube M5 x 20 Torx / Skru M5 x 20 torx 4
Screw M5 x 10 torx / Vis M5 x 10 torx / Schraube M5 x 10 Torx / Skru M5 x 10 torx 4
Washer M5 / Rondelle M5/ Unterlegscheibe M5 / Skive M5 8
Ring tongue / Cosse à oeillet / Anschlussring / terminalring 2
Nut / Ecrou / Nuss / Lokk / nøtt 2

Chat with your Schneider Electric EVlink Pro AC Pedestal manual using AI

Get instant AI answers from your Schneider Electric EVlink Pro AC Pedestal manual

Ask anything about the Schneider Electric EVlink Pro AC Pedestal. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend EVlink Pro AC Pedestal?

Yes No

Frequently Asked Questions

A

It is designed to accommodate up to two charging stations simultaneously. You can configure it for a single unit or convert it to a double setup depending on your specific infrastructure needs.

Is this answer helpful?

A

The pedestal is constructed from aluminum. It is painted grey RAL 7016 to match the charging station body. Stainless steel screws are used throughout the hardware.

Is this answer helpful?

A

Yes, grounding is mandatory. You must connect the pedestal to a ground rod or the charging station terminal to ensure safety and compliance with electrical standards like EV Ready and ZE Ready protocols.

Is this answer helpful?

A

You will need Torx T25 and T10 bits. Specific tightening torques must be observed during assembly. Standard hand tools are typically sufficient for the civil works and mounting process.

Is this answer helpful?

A

No. Installation must only be performed by qualified personnel. They must have skills related to electrical equipment construction and safety training to avoid hazards effectively.

Is this answer helpful?

A

The weight depends on the configuration. A pedestal for a single charging station weighs 9 kg. A pedestal configured for two charging stations weighs 10 kg.

Is this answer helpful?

A

The mechanical protection class is IK10 according to IEC 62262 standards. This ensures resistance against significant mechanical impacts during normal operation.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Durable aluminum construction painted to match charging stations.
  • Mechanical impact protection class IK10 ensures high durability.
  • Compatible with single and double charging station setups.
  • Stainless steel hardware prevents corrosion over time.
  • Clear grounding requirements help meet safety standards.
VS

Disadvantages

  • M16 fixing shanks and nuts are not supplied by manufacturer.
  • Impact protection devices for vehicles are optional accessories.
  • Ground rod installation required if resistance exceeds thresholds.
  • Strict installation rules apply for safety compliance.
  • Specialized tools like Torx T25 needed for assembly.
M: QW-35-FL

Product Specification

Type

Column

M: QW-35-FL

Product Description

Elevate Your EV Charging Infrastructure Stability

Installing an electric vehicle charging station requires a robust foundation to handle the daily operational demands of modern transportation networks. The Schneider Electric Pedestal for Wallbox Pro AC Series Manual provides the essential guidance for this critical process within your facility. This accessory ensures that your power unit remains secure and safe against various environmental factors that could compromise performance over time. Stability is paramount when handling high voltage equipment outdoors exposed to unpredictable weather elements and physical dangers.

Construction Materials and Durability

The pedestal itself is crafted from high quality durable aluminum materials designed for longevity. It features a grey paint finish matching RAL 7016 standards for professional aesthetics. This color coordination helps the unit blend seamlessly into your property landscape without drawing unnecessary attention. Mechanical protection class IK10 offers significant resistance against physical impacts from debris or accidental vehicle contact. Stainless steel screws are utilized throughout the assembly to prevent rust and corrosion over extended periods. The design supports robust usage in demanding commercial settings effectively.

Installation Requirements and Safety

Proper installation is non-negotiable for safety reasons regarding electric shock hazards. Qualified personnel must handle the setup to avoid significant electrical risks to themselves. This ensures adherence to local electrical regulations and national standards regarding electrical safety compliance. Grounding is a crucial safety step for any outdoor electrical installation to prevent failure. If ground resistance exceeds defined thresholds, an additional ground rod is mandatory to prevent shock hazards effectively. Compliance with EV Ready and ZE Ready protocols specifically requires grounding resistance to remain under 100 Ohms for certification approval.

Configuration Options and Flexibility

You can support up to two charging sleeves with a maximum diameter of 62 mm on one unit structure. The system allows conversion from a single to a double charging station pedestal layout easily. This adaptability supports growing infrastructure needs without requiring replacement of the base unit entirely. Impact protection devices around the pedestal are also strongly recommended for vehicle safety and equipment longevity preservation. Civil works must follow applicable standards to secure the ground rods correctly.

Maintenance and Care

Regular checks ensure long-term functionality and safety standards are met. Always observe specified tightening torques during the assembly of all components to ensure structural integrity. Tools like Torx T25 drivers are necessary for proper screw engagement and secure fastening during maintenance. Cable management should be handled carefully to avoid visible wiring beneath the unit for a clean appearance. Packaging materials provided are recyclable to support environmental conservation efforts throughout the installation process efficiently.

Conclusion and Final Thoughts

Following strict guidelines guarantees a safe and efficient charging environment for all users. This accessory transforms a standard wallbox into a sturdy, professional installation ready for public or private use cases. Safety comes first throughout the entire lifecycle of the equipment deployment for maximum reliability.

M: QW-35-FL

© Copyright 2026 Manual.ly