Manual.ly Logo

Schneider Electric Acti9 iCV40N VigiARC Active Manual

0.0 · 0 Ratings

PDF manual · 10 Pages

English

M: OA-GPT-5-NAN
page

/ 10

Loading...
c3a3a6380c02b4a12ab5ab67f4453e378b73 page 1
05/2021 1/10
GDE66871-00
Acti9 - iCV40 VigiARC Active - A9TDFCppp - A9TDECppp - A9TDFDppp
en
Arc fault detection RCBO.
fr
RCBO Détecteur d’arc.
es
Interruptor automático diferencial con detector de arco eléctrico.
it
Interruttore magnetotermico di󰀨erenziale con protezione da arco.
de
Fehlerlichtbogen-Schutzeinrichtung mit FI/LS-Schutz.
PLEASE NOTE
b The installation, maintenance and eventual replacement of this device must only be
carried out by a qualied electrician.
b This device must not be repaired.
b All applicable local, regional and national regulations must be complied with during
the installation, use, maintenance and replacement of this device.
b This device should not be installed if, when unpacking it, you observe that it is
damaged.
b Schneider Electric cannot be held responsible in the event of non-compliance with
the instructions in this document and in the documents to which it refers.
b The service instruction must be observed throughout the life time of this device.
REMARQUE IMPORTANTE
b L’installation, l’entretien et le remplacement éventuel de cet appareil doivent être
e󰀨ectués uniquement par un personnel qualié.
b Cet appareil ne doit pas être réparé.
b Toutes les réglementations locales, régionales et nationales applicables doivent
être respectées lors de l’installation, l’utilisation, l’entretien et le remplacement de cet
appareil.
b Cet appareil ne doit pas être installé si, lors du déballage, vous observez qu’il est
endommagé.
b Schneider Electric ne peut être tenu responsable en cas de non-respect des
instructions contenues dans ce document et dans les documents auxquels il se réfère.
b Les instructions de service doivent être respectées tout au long de la durée de vie
de cet appareil.
TENGA EN CUENTA
b La instalación, el mantenimiento y el eventual reemplazo del equipo eléctrico solo
se debe realizar por personal cualicado.
b El equipo no debe repararse.
b Durante la instalación y el uso de este dispositivo, se deben cumplir todas las
normativas locales, regionales y nacionales aplicables.
b Este dispositivo no debe instalarse si, al desembalarlo, se observa que está
dañado.
b Schneider Electric no se hace responsable en caso de incumplimiento de las
instrucciones de este documento y de los documentos a los que se reere.
b Las instrucciones de uso se deben respetar durante toda la vida útil del producto.
NOTA
b Le operazioni di installazione, utilizzo, riparazione e manutenzione del presente
dispositivo elettrico devono essere eseguite esclusivamente da personale qualicato.
b Il dispositivo non deve essere riparato.
b Durante l’installazione e l’uso del presente dispositivo, è obbligatorio rispettare tutte
le normative locali, regionali e nazionali applicabili.
b Non installare il dispositivo se durante le operazioni di disimballaggio si nota che è
danneggiato.
b Schneider Electric non si assume alcuna responsabilità in caso di mancata
osservanza delle istruzioni riportate nel presente documento e nei documenti a cui
viene fatto riferimento.
b necessario rispettare le istruzioni di servizio per tutta la durata di vita del prodotto.
BITTE BEACHTEN
b Das elektrische Gerät darf ausschließlich von einem qualizierten Elektriker
installiert, verwendet, repariert und gewartet werden.
b Dieses Gerät darf nicht repariert werden.
b Bei der Installation und Verwendung dieses Geräts müssen sämtliche lokalen,
regionalen und nationalen Vorschriften eingehalten werden.
b Dieses Gerät darf nicht installiert werden, wenn Sie beim Auspacken
Beschädigungen feststellen.
b Schneider Electric kann keinesfalls für die Nichtbeachtung der Anweisungen in
dieser Anleitung oder Anweisungen in Dokumenten, auf die sie Bezug nimmt, haftbar
gemacht werden.
b Während der gesamten Produktlebensdauer müssen die Wartungsanweisungen
befolgt werden.
en fr es it de
A9TDFCppp
A9TDECppp
A9TDFDppp

Chat with your Schneider Electric Acti9 iCV40N VigiARC Active manual using AI

Get instant AI answers from your Schneider Electric Acti9 iCV40N VigiARC Active manual

Ask anything about the Schneider Electric Acti9 iCV40N VigiARC Active. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Acti9 iCV40N VigiARC Active?

Yes No

Frequently Asked Questions

A

The unit combines arc-fault detection (series and parallel), residual current protection (30 mA), overcurrent and short-circuit protection (C-curve, 13A), plus diagnostic and wireless communication features for system monitoring.

Is this answer helpful?

A

No. Installation, maintenance and any replacement must be carried out by a qualified electrician. The device must not be repaired; follow local regulations and Schneider Electric instructions.

Is this answer helpful?

A

Run the built-in self-diagnostic after installation and periodically by pressing the Test button (T). The multifunction LED indicates communication status, fault diagnosis and reminds you when an RCD test is due.

Is this answer helpful?

A

Use the product QR code and Schneider Electric’s EcoStruxure Power Commission tools to pair the device with a concentrator via IEEE 802.15.4 wireless link for commissioning, configuration and remote monitoring.

Is this answer helpful?

A

It is designed for 1P+N circuits up to 13A with C-curve characteristics. Higher-current or three-phase circuits require different Acti9 variants with appropriate ratings and breaking capacities.

Is this answer helpful?

A

VISI-TRIP provides tripping diagnosis for earth leakage, arc faults and overvoltage (VISI-TRIP) as well as overload/short-circuit tripping, helping technicians identify the cause of an intervention quickly.

Is this answer helpful?

A

Disconnect all input and output conductors before dielectric (insulation resistance) testing. Always de-energize the device and verify absence of voltage with a rated tester to avoid damage and ensure safety.

Is this answer helpful?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Integrated AFDD + RCD + overcurrent protection reduces fire risk and simplifies panel design.
  • A-SI 30 mA sensitivity offers both arc and human protection while meeting safety norms.
  • Multifunction LED, Test button and VISI-TRIP diagnostics speed fault identification and maintenance.
  • Wireless IEEE 802.15.4 connectivity enables pairing to concentrators for remote monitoring and commissioning.
  • DIN-rail mountable 1P+N form factor and QR-coded commissioning streamline installation.
VS

Disadvantages

  • Must be installed and serviced by qualified electricians; not user-serviceable.
  • Max breaking capacity of 6 kA may be limiting for some high-fault-level installations.
  • 13A rating and C-curve limit suitability to smaller circuits, requiring different units for heavier loads.
  • Device must be replaced if damaged; repairs are not permitted, potentially increasing lifecycle cost.
  • Requires concentrator and EcoStruxure setup for full remote monitoring functionality.
M: OA-GPT-5-NAN

Product Specification

Type

RCBO

Number of poles

1 + N

Rated voltage

230V

Rated current

13A

Rated residual current

30mA

Short-circuit breaking capacity

6kA

Residual current type

A-SI

Tripping characteristic

C

Degree of protection

IP20

Width

1.42in

Modular units

2

Special features

Arc fault protection device, Neutral conductor left

M: OA-GPT-54-NAN

Product Description

Schneider Electric Acti9 iCV40N VigiARC Active — Smart AFDD + RCD Protection

The Schneider Electric Acti9 iCV40N VigiARC Active combines arc-fault detection device (AFDD), residual current device (RCD) with overcurrent protection (FI/LS), and communication capabilities in a compact 1P+N, 13A, C-curve unit. Designed for modern residential and small commercial installations, it protects circuits from parallel and series arc faults, earth leakage, overloads and short-circuits while offering diagnostics and wireless connectivity for remote monitoring and commissioning.

Featuring an A-SI (sensitive instantaneous) trip characteristic and a 30 mA residual current threshold, the iCV40N is tuned to reduce fire risk from arcing faults and to meet safety requirements for human protection. The device supports up to 6 kA short-circuit breaking capacity and is DIN-rail mountable for straightforward integration into distribution boards. A multifunction LED and a Test/Reset button provide local status, automatic reminders for RCD testing, and simple on-site diagnostics.

Practical commissioning is streamlined with a unique product identifier and QR code for use with Schneider Electric’s EcoStruxure Power tools. The integrated wireless link (IEEE 802.15.4 band) enables pairing to a concentrator for system-level monitoring, allowing installers and facility managers to track communication status, receive fault diagnosis (earth leakage, series/parallel arc, overvoltage, internal faults), and respond quickly to events.

Operation guidance emphasizes safety: installation, maintenance and replacement must be carried out by qualified electricians; isolation and voltage testing are mandatory before work; the device must not be repaired and must be replaced if damaged. Built-in self-diagnostics should be run after installation and at regular intervals using the Test button to verify correct operation and trigger reminders if no differential test has been recorded in a year.

With clear visual indications for communication states and detailed VISI-TRIP diagnostics, the iCV40N simplifies fault cause identification (leakage, parallel/series arc, overload/short-circuit, overvoltage or internal fault) and provides recall and acknowledgment sequences for technicians. Dielectric and installation warnings stress de-energizing all conductors before dielectric testing or service, protecting both personnel and the device.

Notes:

  • Intended for use by qualified electricians only; do not attempt repairs.
  • Run self-diagnostic tests after installation and periodically.
  • Observe all local and national regulations for installation and disposal.
  • Use EcoStruxure Power Commission and the product QR code for commissioning and maintenance.
M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly