Rodcraft RC7173 Manual
PDF manual · 36 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your Rodcraft RC7173 manual using AI
Get instant AI answers from your Rodcraft RC7173 manual
Ask anything about the Rodcraft RC7173. Answers come from this manual, with the pages they are based on.
Ask a Question
Do you recommend RC7173?
Yes NoFrequently Asked Questions
The RC7173 is a professional pneumatic angle grinder intended for removing material with abrasive accessories. Typical applications include grinding, surface preparation, and finishing work. It should not be used for purposes outside its intended abrasive material-removal role.
Is this answer helpful?
The RC7173 is specified for a 125 mm, or 4.9 inch, wheel. Always select accessories that are compatible with the grinder, securely install them, and inspect them before use.
Is this answer helpful?
The maximum operating pressure is 6.3 bar, or 90 psi. Use a correctly configured compressed-air supply and avoid exceeding the stated maximum pressure.
Is this answer helpful?
The listed air consumption is 324 l/min, equivalent to 11.5 SCFM. The recommended inner hose diameter is 10 mm, and the air inlet is 1/4 inch NPT. Ensure the compressor and air line can support demand.
Is this answer helpful?
The grinder uses a trigger control. Pull the trigger to start the tool, apply more pressure to increase speed, and release the trigger to stop operation. This lets the operator adjust output to the task.
Is this answer helpful?
Clean the air inlet nipple, place about three drops of Rodcraft air oil into it, and run the tool briefly. Perform this routine before and after use to help support the tool's service life.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- 12,000 RPM and 700 W output support fast abrasive material removal.
- 125 mm wheel capacity and M14 spindle suit common professional grinding accessories.
- Variable trigger provides direct speed control during operation.
- At about 1.5 kg, it offers capable output in a relatively manageable format.
Disadvantages
- Requires a compressed-air system capable of supplying 324 l/min or 11.5 SCFM.
- Noise and vibration exposure require suitable PPE and work-time management.
- Daily use calls for disassembly and inspection every three months.
- Designed only for professional abrasive material removal, limiting alternative uses.
Product Specification
Type
Angle grinder
Operating pressure
91.4 psi
Air consumption
19.07 cfm
No-load speed
12,000 rpm
Disc diameter
4.92 in
Tool holder
M14 spindle thread
Special features
Auxiliary handle
Weight
3.31 lb
Product Description
Rodcraft RC7173 Pneumatic Angle Grinder - Read, Download & Print Free
The Rodcraft RC7173 Pneumatic Angle Grinder is a professional air-powered tool built for abrasive material removal in workshop, fabrication, bodywork, and maintenance environments. Designed around a compact angle-grinder format, it combines a 125 mm wheel capacity with a 12,000 RPM free speed for efficient grinding, surface preparation, and finishing tasks where responsive power matters.
Built for Professional Abrasive Work
Powered by compressed air, the RC7173 delivers 700 W, or 0.93 HP, while operating at a maximum air pressure of 6.3 bar (90 psi). Its M14 spindle thread supports compatible grinding accessories, while the 1/4 inch NPT air inlet and recommended 10 mm inner hose diameter help establish a suitable air connection. With an air consumption rating of 324 l/min, equivalent to 11.5 SCFM, the tool should be paired with an adequately sized compressor and air supply setup.
At approximately 1.5 kg, the grinder offers a practical balance between output and handling. Its listed dimensions of 245 x 80 mm make it suitable for users who need a capable pneumatic tool without moving to a larger, heavier unit. A variable-speed trigger gives the operator direct control: increased trigger pressure increases speed, and releasing the trigger stops the machine.
Setup and Everyday Operation
Accessories must be secured correctly before use. When using a backing plate, it needs to be firmly screwed onto the drive spindle. Remove the tightening wrench before starting the grinder, then connect the air supply and operate the trigger only when the work area is ready.
The RC7173 is intended exclusively for professional material removal with abrasives. It is not designed for unrelated tasks or improvised accessories. Selecting the right wheel, checking its condition, and following workplace safety procedures are essential for productive use.
Care That Supports Service Life
Routine lubrication is an important part of pneumatic-tool ownership. Clean the air inlet nipple, add about three drops of Rodcraft air oil, and briefly run the grinder. Repeating this process before and after use can help support long-term performance.
For tools used every day, a complete disassembly and inspection every three months is recommended. Replace worn or damaged parts, disconnect the air source before maintenance, and use qualified personnel and original spare parts for repairs.
Note: The stated noise and vibration figures come from laboratory testing. Real exposure varies with the accessory, workpiece, workstation, operating technique, and duration of use. Use suitable hearing protection, manage vibration exposure, and remove damaged equipment from service.
Key Takeaway
The Rodcraft RC7173 Pneumatic Angle Grinder is a focused professional solution for 125 mm abrasive work. Its 12,000 RPM speed, M14 spindle, trigger-controlled operation, and straightforward lubrication routine make it a practical option for air-tool users who prioritize controlled grinding performance and regular preventive maintenance.
Search for 67,706 Manuals online
Type-in Brand or Model