Manual.ly Logo

Renegade RXA 1200 D Manual

0.0 · 0 Ratings

PDF manual · 40 Pages

English

M: QW-35-FL
page

/ 40

Loading...
08b5a8d13230ff4eb4cd5055e3a2a83673af page a
10
IMPORTANT NOTES PRIOR TO INSTALLATION
- This device is only suited for a 12 volt system with negative ground.
- Theradiatedheatwhileoperationrequiressufcientaircirculationattheplaceofinstallation.Itis
veryimportantthattheheatsinknsdonothavecontactwithanymetalpartsoranysurfaceswhich
couldimpairaircirculation.Theampliermaynotbeinstalledinsmallclosedlocationorspaces
without air circulation (e.g. spare wheel recess or below the vehicle carpeting). We recommend the
installationinthevehicle’strunk.Ensuresufcientprotectionagainstvibrations,dustanddirt.
- Ensurethattheinputandoutputcablesaresufcientlyseparatedfromthepowersupplycables.
Otherwise interferences may occur.
- Ensure the accessibility of the fuse and the operating elements after installation.
- Thereliabilityandperformanceoftheamplierdependsonthequalityofinstallation.Preferably
consult an expert to install the system, particularly if you want to install several loudspeakers.
POWER SUPPLY AND TURN-ON-CONNECTION
ATTENTION: Before you start with the installation, disconnect the ground connection from the ve-
hicle’s battery in order to prevent short circuits.
Thepowerwiringwhichisusuallyinstalledinon-boardcarnetworksisnotsufcientforapoweramplier‘s
demands.MakesurethatthepowerwirestoGNDandtothe+12Vterminalhasbeensufcientlyspecied.A
cable cross section of at least 10 mm
2
mustbeusedtoconnectthebatterytotheamplier‘sterminals.
FirstconnecttheGNDterminaloftheampliertoanappropriategroundconnectionatthechassis.Toensurea
good connection, residue dirt and dust from the connection point. A loose connection may cause malfunctions
or interferences noise and distortion.
Thenconnectthe+12Vterminaloftheamplierwiththebatterybyusinganappropriatecableincludingan
in-line fuse. This fuse should be located very close to the battery; for safety reasons not more than 30 cm away.
Sincetheamplierdoesnothaveaninternaldevicefuse,anotherfusewith100Amustbeinstalledveryclose
totheampliertothispowercable.
Thenconnecttheremoteturn-on-wirefromtheheadunitwiththeamplier‘sREMterminal.Acablewitha
cross-section of 0.5 mm
2
is adequate.
LOUDSPEAKER CONNECTION
- The total impedance must not be lower than 1 ohm.
- Never connect loudspeaker cables with the ground of the chassis or the +12 V supply voltage.
Iftheamplierisoperatedwithatoolowimpedanceorincorrectlyused,theentiresoundsystemmaybedam-
aged. This means a warranty void in such cases.
AUDIO SIGNAL CABLES
When installing the audio cables between the RCA outputs of the head unit and the RCA inputs of the ampli-
er(Fig.1,8),theaudioandpowersupplycablesshould,ifpossible,notberoutedalongthesamesideofthe
vehicle. We recommend a separated installation, e.g. routing the power cable through the cable channel on
the left side and the audio cables through the cable channel of the vehicle on the right side or vice versa. This
prevents interferences due to crosstalk into the audio signal.

Chat with your Renegade RXA 1200 D manual using AI

Get instant AI answers from your Renegade RXA 1200 D manual

Ask anything about the Renegade RXA 1200 D. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend RXA 1200 D?

Yes No

Frequently Asked Questions

A

The amplifier can deliver a maximum of 1200 watts at 1 ohm, 900 watts at 2 ohms, and 600 watts at 4 ohms, providing immense power for subwoofers.

Is this answer helpful?

A

Yes, you can use the Master/Slave function to link two identical units. This doubles the total power output and allows both amps to share the same crossover settings controlled by the master unit.

Is this answer helpful?

A

Yes, it features an automatic turn-on function that activates when it detects a voltage rise via the high-level inputs. However, this works with 90% of head units and may not function with very old models.

Is this answer helpful?

A

No, if you use the high-level inputs for the auto turn-on feature, the REM terminal is not needed. Otherwise, you can connect a standard remote wire from your head unit.

Is this answer helpful?

A

The built-in protection circuit will detect overheating or low impedance shorts. The red LED will light up, and the amplifier will automatically shut down to prevent damage until it cools down.

Is this answer helpful?

A

Use the included cable remote controller. Connect it to the REMOTE port on the amplifier to adjust the bass boost level directly from the driver's seat.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Delivers up to 1200W RMS power at 1 ohm for intense bass response
  • Supports Master/Slave linking to combine two amplifiers into one system
  • Includes variable low-pass, subsonic filters, and 12dB bass boost
  • Features high-level inputs for use with radios lacking RCA outputs
  • Comes with a wired bass level remote for convenient on-the-fly adjustments
VS

Disadvantages

  • Requires external fuses as no internal device fuse is included
  • Needs significant cooling airflow and cannot be installed in enclosed spaces
  • High current draw requires heavy gauge wiring (minimum 10mm2)
  • Automatic turn-on may not work with older head units lacking DC offset
  • Complex wiring for Master/Slave mode requires careful polarity matching
M: QW-35-FL

Product Specification

Type

Mono Amplifier

Channels

1

Power 4Ω

1x 300W

Power 2Ω

1x 450W

Power 1Ω

1x 600W

Dimensions

8.7x1.9x10.6in

M: QW-35-FL

Product Description

Renegade RXA 1200D: Unleash Deep Bass in Your Vehicle

The Renegade RXA 1200D is a powerful monoblock amplifier designed specifically for car audio enthusiasts who demand high performance and reliability. This Class D mono amplifier delivers exceptional power output, reaching up to 1200 watts at 1 ohm, ensuring your subwoofers receive the energy they need to produce earth-shaking bass. Its compact design measures just 220 x 48 x 240 mm, making it easy to fit into various vehicle trunks without taking up excessive space.

One of the standout features of the RXA 1200D is its versatility in configuration. It supports Master/Slave linking, allowing you to connect two units to double your power output while maintaining synchronized crossover settings. The built-in variable low-pass filter lets you fine-tune frequencies between 40 and 150 Hz, while the subsonic filter removes unwanted infrasonic content below 35 Hz to protect your speakers and improve sound clarity. Additionally, the adjustable bass boost offers a gain of up to 12 dB at 40 Hz, giving you precise control over the low-end punch.

Installation is straightforward with multiple input options. If your head unit lacks pre-out RCA connections, the high-level inputs allow direct connection using speaker wires. The automatic turn-on feature detects voltage changes on these high-level inputs, eliminating the need for a separate remote turn-on wire in many setups. For those seeking ultimate control, a wired bass level remote controller is included, enabling adjustments from the driver's seat. Safety is prioritized with an integrated protection circuit that monitors temperature and impedance, shutting down the unit if overheating or short circuits occur.

Whether you are building a single-subwoofer system or a dual-amplifier setup, the Renegade RXA 1200D provides the robust foundation needed for a superior auditory experience. Ensure proper ventilation during installation to maintain optimal performance and longevity.

M: QW-35-FL

© Copyright 2026 Manual.ly