Manual.ly Logo

Renegade REN10KIT Manual

4.7 · 31 Ratings

PDF manual · 2 Pages

English

M: OA-GPT-54-NAN
page

/ 2

Loading...
646b548426fb38604e56cc24212991f69f23 page 2
Lead one end of the POWER CABLE (red) from the car battery area through the car to the +12V terminal of the
amplifier and connect it. Then connect the other end of the cable with the FUSE HOLDER at the suitable terminal.
INSTALLATION GUIDE
REN10/20/35KIT
2-CHANNEL AMPLIFIERS
Chassis
Amplifier
Head unit
1
Ground Cable
2
RCA / Cinch Cable
6
Remote Wire
7
7
REM
FUSE
Fuse Holder
3
Power Cable
5
4
Cut-off Part
Please attend the following instructions:
1
2
Connect the GROUND CABLE (brown, 0.8m) with the ground terminal of the amplifier and a suitable GROUND contact
point on the car chassis, with a maximum distance of 1 meter from the amplifier. Use the ringterminal for the GROUND
contact point. Ensure that all paint or other insulation is removed from around the hole area.
3
Find a suitable position for the FUSE HOLDER next to the car battery’s PLUS POLE. The maximum distance should
not be more than 30 cm. Please ensure, that you don’t damage any parts of the car, like the fuel tank, wires etc.
4
Cut off a part of the POWER CABLE (red, 5m) on one end, which has the same length like the distance from the
battery’s PLUS POLE to the FUSE HOLDER (max. 30cm). Connect this part on the end without ringterminal with the
FUSE HOLDER (without inserted fuse) and the other end to the battery’s PLUS POLE. Use for the connection the
supplied ring terminals.
5
6
Lead the RCA/CINCH CABLE pair with attached REMOTE WIRE from the HEAD UNIT through the car to the
amplifier’s position. Then connect the RCA/CINCH plugs on one end with amplifier, and the other end with the HEAD
UNIT RCA/CINCH outputs. Please observe the correct polarity of all connections.
7
Connect the one end of the attached REMOTE WIRE with the REMOTE/REM terminal of the HEAD UNIT and the
other end with the REMOTE/REM terminal of the amplifier. This wire provides a turn on/turn off signal to the amplifier,
when the HEAD UNIT is turned on / turned off. NOTE: some amplifier types may require, that you have to extend the
REMOTE WIRE with a suitable cable, to lead the REMOTE WIRE to the other endpanel of the amplifier.
8
At least insert the FUSE into the FUSE HOLDER. Ensure not to cause a short circuit, or your car’s electric system
may get damaged. Do not touch the bare metal parts of the cable or the car battery, otherwise a risk of electric shock
consists. Then re-connect the negative ground connection to the vehicle’s battery.
If you have followed all instructions above, your car audio system is ready for operation. Then follow the further
instructions of the OWNER’S MANUALS of your amplifier and your head unit.
IMPORTANT NOTES:
- Follow by any means the instructions on the left.
- Do not damage any parts of the car like the
fuel tank, electronic system, airbags etc.
- Do not bend or splice any wires or cables.
- Do not touch any bare metal parts of the power cable or
the vehicle’s battery.
- Ensure always the correct polarity of all connections.
- Avoid any short circuits.
- Consult your retailer or car service station in case of open
question or problems.
- Replace the fuse in the fuse holder only with spare
fuses of the same value:
REN10KIT 40A AGU
REN20KIT 60A AGU
REN35KIT 100A ANL
Disconnect at first the negative ground connection from the vehicle’s battery.
Battery

Chat with your Renegade REN10KIT manual using AI

Get instant AI answers from your Renegade REN10KIT manual

Ask anything about the Renegade REN10KIT. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend REN10KIT?

Yes No
0
User Pic

Marius Keller

8 months ago

Will the included ground (mass) cable be long enough, and are the RCA and other connectors reliable for a car amp installation?

0
User Pic

Manual.ly

8 months ago

Most buyers find the supplied cable lengths sufficient, but some note the ground (mass) wire can be a bit short depending on your vehicle and where you can attach a good chassis ground. Before ordering, measure the route from the amp to the intended ground point and the run to the head unit, and choose a solid, bare-metal ground location. For reliability, the connectors are generally fine when handled carefully during installation and routing (avoid sharp bends and excessive force when inserting). If a plug or pin arrives damaged or breaks during fitting, please contact support with photos so we can help with a replacement. For systems under about 500 W, this kit is typically suitable; for higher power, consider a thicker-cable kit.

M: OA-GPT-5-NAN
M: OA-GPT-5-NAN

Frequently Asked Questions

A

It is used to connect a car amplifier safely and neatly. The kit supports power delivery, grounding, RCA signal transfer, and remote turn-on wiring for a 2-channel audio setup.

Is this answer helpful?

A

Disconnecting the negative battery terminal helps prevent short circuits and reduces the risk of electric shock while routing cables or connecting the fuse holder and power lead.

Is this answer helpful?

A

It should be placed close to the battery’s positive terminal, ideally within 30 cm. This helps protect the vehicle’s electrical system if the power cable is damaged or shorted.

Is this answer helpful?

A

The ground cable links the amplifier to a solid chassis point on the car. A short, clean ground connection helps the amplifier operate reliably and reduces the chance of noise issues.

Is this answer helpful?

A

The remote wire carries the on/off signal from the head unit to the amplifier. It tells the amplifier when to power up and when to shut down with the audio system.

Is this answer helpful?

A

Yes. In some amplifier installations, the supplied remote wire may not reach far enough. If that happens, a suitable extension cable can be used to complete the connection safely.

Is this answer helpful?

A

Only a fuse with the same rating as the original should be used. The kit versions may require different values, such as 40A, 60A, or 100A, depending on the model.

Is this answer helpful?

M: OA-GPT-54-NAN

Advantages and Disadvantages

Advantages

  • Complete wiring solution for a 2-channel amplifier setup with power, ground, RCA, remote, and fuse holder.
  • Safety-focused design encourages proper fuse placement, correct polarity, and careful battery disconnection.
  • Clear installation steps help keep cables organized and reduce the chance of loose or noisy connections.
  • Multiple kit versions with different fuse ratings make it easier to match common amplifier power needs.
VS

Disadvantages

  • Installation still requires basic car-audio knowledge and careful handling of vehicle wiring.
  • Some setups may need extra cable length, especially for the remote wire or unusual amplifier placement.
  • The user must supply careful workmanship; poor grounding or routing can reduce performance.
  • Replacement fuses must match the exact rating, so there is little flexibility if the system changes.
M: OA-GPT-54-NAN

Product Specification

Type

Cable

M: OA-GPT-54-NAN

Product Description

Renegade REN10KIT Manual: Clean Power and Control for a 2-Channel Amp Setup

The Renegade REN10KIT Manual centers on a straightforward idea: help you wire a car audio amplifier safely, neatly, and with reliable power delivery. The REN10KIT is presented as a practical installation kit for 2-channel amplifiers, bringing together the essential parts needed to connect the battery, amplifier, head unit, and grounding point without unnecessary complexity.

At the heart of the setup is the power path. The red power cable runs from the vehicle battery area to the amplifier’s +12V terminal, while a fuse holder is placed as close to the battery as possible for protection. This detail matters because it reduces risk and helps protect the vehicle’s electrical system if a fault occurs. The kit also includes a brown ground cable, which should be attached to a clean, bare metal chassis point near the amplifier for stable performance.

The audio signal path is equally important. The RCA/Cinch cable connects the head unit to the amplifier, while the blue remote wire carries the turn-on signal so the amplifier powers up and shuts down with the system. This creates a more organized installation and supports reliable operation. The guide also stresses correct polarity, careful routing, and avoiding damage to sensitive vehicle parts such as fuel lines, wiring, airbags, and the battery itself.

One of the strengths of this kit is its emphasis on good installation habits. The battery should be disconnected before work begins, the fuse must be inserted only at the final step, and any replacement fuse must match the original rating. Different variants use different fuse values, such as 40A, 60A, or 100A depending on the kit version. For many users, this makes the REN10KIT a sensible choice for building a cleaner and safer car audio layout.

Notes

  • Fuse placement near the battery is a key safety step.
  • Grounding should be short, solid, and free of paint or insulation.
  • Some amplifiers may need an extended remote wire.
  • After installation, follow the amplifier and head unit instructions for final setup.
  • If anything is unclear, consulting a car audio specialist is the safest option.
M: OA-GPT-54-NAN

© Copyright 2026 Manual.ly