Manual.ly Logo

Pieps iProbe BT 260 Manual

0.0 · 0 Ratings

PDF manual · 17 Pages

English

M: claude-opus-5-5
page

/ 17

Loading...
880120f5fed220582bd74fe963d30161ff4d page 9
Manual PIEPS iPROBE BT | 08/2020 9 / 17
SWITCHING ON | SELF-CHECK
To switch on the PIEPS iPROBE BT go through these steps:
• Open the elastic closure buckle (1C).
• Eject the PIEPS iPROBE BT into soft ground (snow) and tension the probe. To do so, hold the top part of
the probe tube with one hand and with the other hand pull the probe handle (1A) until the quick-closing
latch (1B) clicks into place and a beep from the loudspeaker (1H) indicates that the PIEPS iPROBE BT is
switched on.
4.2.1 Self-check
When switching on the PIEPS iPROBE BT an extensive self-check is performed, and all relevant system
components are tested.
PIEPS iPROBE BT Status
Optical signal indication (LEDs)
Acoustic signal indication
Switching on
Continuous tone for 1 s (piiiiiiiiiiep)
Self-check
Self-check
„OK“
Both LEDs lit GREEN for 1 second
No acoustic signal
Self-check
„Low battery
capacity“
Both LEDs flash RED for 3 seconds
Warning tone for 3 seconds (5x piiiep),
see Replacing the battery
Self-check
„System error“
Both LEDs lit RED as long as the PIEPS
iPROBE BT is switched on
Warning tone for 3 seconds (5x piiiep),
see Troubleshooting
• If the PIEPS iPROBE BT is OK (self-check “OK”), a green LED-light lits for 1 second. The LED-light of the
Check A1 then starts flashing and the PIEPS iPROBE BT can be used.
• If the battery needs to be replaced (low battery capacity self-check), a red flashing LED light and an
acoustic warning signal will be indicated for 3 seconds. The LED-light of the Check A1 then starts flashing
and the PIEPS iPROBE BT can be used. In this case, replace the battery.
• If the PIEPS iPROBE BT shows an error (system error self-test), a permanent red LED-light and an acoustic
warning signal will be indicated for 3 seconds. The optical warning will continue as long as the PIEPS
iPROBE BT is activated. The electronic functionalities are not available. In this case, perform
troubleshooting.
NOTICE
If the PIEPS iPROBE BT is defect (system error self-check), no electronic functionalities are available,
and any electronic support will lapse. In this case, use the PIEPS iPROBE BT like a classic avalanche
probe.
NOTICE
The switching on of the electronic is confirmed with an acoustic (Piep-tone) signal.
Continuous signal for 1 second (piiiiiiiiiiep)

Chat with your Pieps iProbe BT 260 manual using AI

Get instant AI answers from your Pieps iProbe BT 260 manual

Ask anything about the Pieps iProbe BT 260. Answers come from this manual, with the pages they are based on.

iProbe BT 260 Maintenance Schedule

Before each use
Perform self-check and inspect for damage

Switch on the device to run a self-check. Check for physical damage and ensure battery capacity is sufficient before every use.

As needed
Replace battery when low warning appears

Replace the AA alkaline battery immediately if the red flashing LED and warning tone indicate low battery capacity during the self-test.

Show in the manual (page 16)
Seasonal
Remove batteries for long-term storage

If the device is not used for extended periods (e.g., summer months), remove the batteries from the compartment to prevent leakage damage.

Show in the manual (page 17)
M: qwen/qwen3.8-flash

Ask a Question

0/1000

Do you recommend iProbe BT 260?

Yes No

Frequently Asked Questions

A

The device features an automatic sleep-mode that temporarily deactivates a beacon once it is located. This allows the rescuer to immediately see the next strongest signal on their receiver, saving valuable time when searching for additional victims.

Is this answer helpful?

A

You must use only Alkaline AA batteries (LR6, 1.5V). Using other types or damaged batteries can lead to explosion risks or incorrect capacity readings. Replace them immediately if the low battery warning appears.

Is this answer helpful?

A

Yes, you can connect the Pieps iProbe BT to the PIEPS APP via Bluetooth. This allows for software updates, device configuration, and access to a training mode. However, never use Bluetooth mode while in avalanche terrain.

Is this answer helpful?

A

If the self-check indicates a system error, the electronic functionalities will not work. You should treat the device as a classic mechanical avalanche probe and contact support or a retailer for repairs.

Is this answer helpful?

A

When the probe tip is within 0.5 meters of a transmitting beacon, the device triggers a hit indicator. Both LEDs will light up blue continuously, and a continuous tone will sound from the loudspeaker.

Is this answer helpful?

A

Yes, the probe tube includes a centimeter scale. This allows users to measure the depth of the snow profile accurately while also using the probe for locating buried victims.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Provides optical and acoustic hit indicators for accurate pinpointing
  • Features automatic sleep-mode to handle multiple burial scenarios efficiently
  • Includes Bluetooth connectivity for software updates and training via the PIEPS APP
  • Offers a built-in centimeter scale for measuring snow profile depth
  • Uses a Speed-Cone system for quick and easy probe extension
VS

Disadvantages

  • Requires specific Alkaline AA batteries which may need frequent replacement in cold weather
  • Bluetooth functionality must be disabled during active avalanche rescue operations
  • Electronic features fail completely if a system error occurs during self-check
  • Device performance can be compromised by exposure to extreme temperatures outside limits
  • Users with impaired vision or hearing must ensure they can interpret visual or audio cues
M: QW-35-FL

Product Specification

Type

Avalanche probe

Length

8.53 ft

Weight

0.93 lbs

M: QW-35-FL

Product Description

Pieps iProbe BT 260: Revolutionizing Avalanche Rescue

The Pieps iProbe BT 260 represents a significant leap forward in avalanche safety technology. Designed for both inexperienced beginners and trained professional rescuers, this electronic avalanche probe integrates optical and acoustic hit indicators to provide maximum support during pinpointing operations. Whether you are conducting a solo rescue or participating in an organized operation, the device saves crucial time by offering immediate feedback when approaching a buried victim.

At the heart of the Pieps iProbe BT 260 is its ability to detect standard avalanche beacons transmitting according to EN300718 standards. The device features a Speed-Cone system for rapid extension and a quick-closing latch that ensures reliable locking. Users benefit from a centimeter scale on the probe tube, allowing for precise depth measurement of snow profiles. The inclusion of PIEPS Safety Markers at 100 cm and 40 cm helps rescuers visualize the burial depth instantly. Furthermore, the device supports multiple burials through an automatic sleep-mode feature that deactivates beacons once they are found, allowing rescuers to focus on the next signal without manual intervention.

Connectivity is another standout feature, managed via the PIEPS APP over Bluetooth. This allows for software updates, device configuration, and access to a practical training mode. The self-check function upon activation ensures all components are working correctly, displaying status via green, red, and blue LEDs alongside distinct acoustic signals. With a total length of 260 cm and a weight of just 420 grams including the battery, it balances portability with the reach needed for deep burials. The elastic closure buckle keeps the folded unit secure in your backpack emergency pocket, ensuring it is ready for deployment whenever the terrain demands it.

Key Features

  • Optical and acoustic hit indicators for precise location.
  • Automatic beacon deactivation for multiple burial scenarios.
  • Bluetooth connectivity for app management and training.
  • Durable construction with a centimeter scale for snow profiling.
  • Fast assembly with the Speed-Cone system.

Important Notes

  • Always read the operating manual before first use.
  • Use only Alkaline AA batteries (LR6, 1.5V).
  • Do not expose the device to extreme temperatures outside -20°C to +45°C.
  • Store in a dry place and remove batteries if not used for extended periods.
M: claude-opus-5-5

© Copyright 2026 Manual.ly