Manual.ly Logo

Pewag Servostar Manual

0.0 · 0 Ratings

PDF manual · 20 Pages

English

M: QW-35-FL
page

/ 20

Loading...
1d5fdc527dfea5ec383e77f85f63f416ddd2 page 8
8
Customer Information
It is absolutely necessary to adjust the chain before first use. As a
result mounting is easier in the course of winter conditions. Smooth
and quick mounting is possible only when chain is optimally
adapted to tire and rim.
Content
1) Adapter for fastening to the wheel nut
a) Clamp with wrench width 17, 19 and 21/22 mm
b) Sleeve for clamp
2a+b) Spacer
3a) Screw long
3b) Screw medium
3c) Screw short
4+5) Tools for size adjustment
6) Wrench
*) pre-assembled
Chain Adjustment to the
Dimension (Prepare A)
For some tire sizes an adjustment of the chain dimension is
necessary. Check your tire dimension, look for it in the dimension
setup table at the end, and remove, if necessary, the specified
number of adjustment elements (yellow) with enclosed tools as
shown in the figure.
Explanation: ok = no adjustment necessary, -1 = remove 1
element, -2 = remove 2 elements etc.
For removing 2 or 4 elements, always remove the opposite
elements. Keep the removed parts –this chain can be reused for
other tire dimension. Note: These instructions are generally valid
and non-binding and are results of tests and our experience.
Therefore, a fitting test before the first use is urgently
recommended.
Check the fit of the chain after approx. 50 m. Readjust if needed
(remove more adjustment elements if the chain does NOT pull
automatically on the tire).
Adapter Adjustment (Prepare B)
To adjust the adapter, remove the wheel cover and wheel nut caps.
Remove any dirt, snow or ice. Move the slide switch of the ratchet
to the “open” position and pull out the cable on which the adapter
is fixed. To do this, move the slide switch as much as possible in
the direction“open”. After that, move it slightly back in direction
“drive” and then you can move it to the end of direction “open”.
Now check whether the pre-assembled adapter fits onto the wheel
nut. If the adapter touches the rim as shown in figure 2, the adapter
has to be elongate (see fig. 4-6).As a basic principle: screw the
adapter as close as possible to the rim (see fig. 1) without touching
it. End of adjustment.
Fig. 3a: The hexagon of the clamp has to be pushed completely
through the opening of the sleeve. So the clamp can be
fastened correctly to the wheel nut.
Fig. 3b: The clamp must be placed straight and completely on the
hexagon nut of the wheel nut for secure attachment.
Fig. 4: Pre-mounted: short.
Fig. 5: Alternative: medium -> change spacer and screw.
Fig. 6: Alternative: long -> add spacer and change screw.
EN

Chat with your Pewag Servostar manual using AI

Get instant AI answers from your Pewag Servostar manual

Ask anything about the Pewag Servostar. Answers come from this manual, with the pages they are based on.

Ask a Question

0/1000

Do you recommend Servostar?

Yes No

Frequently Asked Questions

A

Yes, it is absolutely necessary to adjust the chain length to match your specific tire dimensions before the first use. This ensures a smooth fit and prevents damage to the wheels.

Is this answer helpful?

A

Consult the dimension table included with the product. It lists tire sizes and indicates exactly how many yellow adjustment elements need to be removed for each size.

Is this answer helpful?

A

Absolutely. The chain is designed to be reusable. Simply keep the removed adjustment elements and reconfigure the chain length according to the new tire dimensions when switching vehicles.

Is this answer helpful?

A

If the chain fails to pull onto the tire, drive forward approximately half a wheel rotation. Then manually pull the loose sections onto the tire and check the tension again.

Is this answer helpful?

A

It is designed specifically for passenger cars (PKW). Always refer to your vehicle manufacturer's guidelines to ensure compatibility with your specific wheel type and clearance.

Is this answer helpful?

A

You should check the fit and tension after driving approximately 50 meters or 150 feet. Further adjustments may be needed if the chain has not tightened sufficiently.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • Automatic tensioning system simplifies installation significantly
  • Adjustable design fits a wide range of tire dimensions
  • Reusable components allow adaptation for different vehicles
  • Built-in visual indicator ensures correct chain tension
  • Quick mounting process saves time in bad weather
VS

Disadvantages

  • Requires pre-use adjustment for correct tire sizing
  • Initial setup takes more time than non-adjustable chains
  • Adapter must be carefully aligned to avoid rim contact
  • Not suitable for heavy trucks or commercial vehicles
  • Manual removal of elements required if not pre-set
M: QW-35-FL

Product Specification

Vehicle Type

Passenger Car

Type

Snow Chain

Tensioning

Automatic

Link Thickness

0.13 inches

Tread Width

0.47 inches

Rim Protection

Yes

M: QW-35-FL

Product Description

Pewag Servostar: The Ultimate Winter Driving Solution

Navigating winter roads requires reliable equipment, and the Pewag Servostar stands out as a premier choice for passenger car owners. This innovative snow chain system is designed to simplify the often tedious process of fitting chains in harsh weather conditions. By integrating an automatic tensioning mechanism, it ensures that drivers can achieve optimal grip without the struggle of manual tightening or constant readjustments.

The core advantage of the Pewag Servostar lies in its adaptability. Before the first use, the chain must be adjusted to match specific tire dimensions. This preparation involves removing specific elements from the chain mesh based on a detailed size table provided with the product. Once the correct length is set, the adapter is customized to fit various wheel nut sizes securely. This modular approach allows a single set of chains to serve multiple vehicles with different tire specifications, offering exceptional versatility and long-term value.

Installation is remarkably straightforward thanks to the smart ratchet system. Users simply drape the arms over the tire, attach the adapter to the wheel nut, and engage the drive mode. Turning the hand wheel automatically pulls the chain tight against the tire surface. The built-in indicator ensures perfect tension, eliminating guesswork. After driving a short distance, the system self-adjusts further, guaranteeing safety and performance throughout your journey. Whether facing icy highways or snowy mountain passes, the Pewag Servostar provides the confidence needed to travel safely.

Notes:

  • Always check vehicle manufacturer warnings before installation.
  • Perform a test drive after initial setup to verify fitment.
  • Keep removed chain elements for future reuse on different tires.
M: QW-35-FL

© Copyright 2026 Manual.ly