Manual.ly Logo

Papst 8214 JH4 Manual

0.0 · 0 Ratings

PDF manual · 5 Pages

English

M: QW-35-FL
page

/ 5

Loading...
ff5b0332193e39a15f1d99636b5fcb449e47 page 1
page 1 of 5
Operating manual
8214 JH4
Product type, manufacturing date (calendar week/year of construction)
and if required, conformity mark can be found on the nameplate on the
product.
Please provide us with the contents of the nameplate when making
enquiries about the product.
ebm-papst St.Georgen GmbH & Co. KG
Hermann-Papst-Straße 1
D - 78112 St.Georgen
Phone: +49 (0) 7724 / 81-0
Fax: +49 (0) 7724 / 81-1309
info2@de.ebmpapst.com
www.ebmpapst.com
As per: 15.08.2012
Version 1 5
Article number: 9692910197
Original operating manual
INDEX
1 SAFETY REGULATIONS AND INFORMATION 1
2 INTENDED USE 3
3 TECHNICAL DATA 3
4 CONNECTION AND COMMISSIONING 3
5 FAULTS, POSSIBLE CAUSES AND REMEDIES 4
1 SAFETY REGULATIONS AND INFORMATION
Read the operating manual carefully before commencing work at the
product. Pay attention to the following warnings to avoid risk to
persons or malfunctioning.
This operating manual is an integral part of the product.
In the event of resale or change of ownership the operating manual
must accompany the product. This operating manual may be copied
and provided as information on potential risks and their avoidance.
Hazard classification of warning notices
The following risk ratings are used in this operating manual to denote
potential risk situations and important safety instructions:
DANGER
This is a potentially dangerous situation
and warns of an impending health risk
or risk of fatal injury if this warning is
not observed. Observe this warning.
WARNING
The dangerous situation can occur and
can result in major or fatal injuries if the
warning is not observed. Work with
extreme care.
CAUTION
The dangerous situation can occur and
can result in minor injuries or damage
to property if the warning is not
observed.
NOTE
A potentially dangerous situation can
occur and results in damage to
property if not avoided.
Qualification of personnel
Only skilled electricians are permitted to install the product, to carry out
the test run and to work at the electrical unit.
Only instructed and authorized skilled personnel are permitted to
transport, unpack, operate and service the product.
Basic safety regulations
Safety risks related to the product must be reassessed after installing
in the final device.
The operating manual was developed in accordance with European
market requirements and may need adapting to the market
requirements of the country in question.
When working at the product, observe the following:
Do not make any changes to the product.
WARNING
Impermissible high load
Stop the product immediately after
impermissible loading (e.g. impact,
heat, overvoltage).

Chat with your Papst 8214 JH4 manual using AI

Get instant AI answers from your Papst 8214 JH4 manual

Ask anything about the Papst 8214 JH4. Answers come from this manual, with the pages they are based on.

8214 JH4 Maintenance Schedule

Remind me when maintenance is due
Semiannual
Inspect protective equipment and clothing

Perform a visual inspection of protection against accidental contact and protective clothing.

Semiannual
Inspect the product for damage

Perform a visual inspection of the product for damage.

Semiannual
Inspect product fixation

Perform a visual inspection of the product fixation.

Semiannual
Inspect wire fixation

Perform a visual inspection of wire fixation.

Semiannual
Inspect wire insulation

Perform a visual inspection of wire insulation.

Semiannual
Inspect impeller for wear and deposits

Perform a visual inspection of the impeller for wear, sediments, and corrosion.

Yearly
Run the product to move motor bearings

If the product is not operated for a longer period, run it for about 15 minutes annually to move the motor bearings.

Free maintenance reminders

Timed to your purchase date. Always free, unsubscribe anytime.

By submitting you agree to the privacy policy. Unsubscribe with one click in any email.
M: gpt-5.6-terra

Ask a Question

0/1000

Do you recommend 8214 JH4?

Yes No

Frequently Asked Questions

A

No, you must replace the product with a new one. Do not attempt to repair the unit yourself.

Is this answer helpful?

A

No, speed control via PWM is not permitted. Only voltage supply control within the stipulated range is allowed.

Is this answer helpful?

A

The permitted ambient temperature for operation is up to 70 degrees Celsius.

Is this answer helpful?

A

Do not use cleaning agents that contain acids, caustic solutions, or solvents. Use only a moist cloth.

Is this answer helpful?

A

Only skilled electricians are permitted to install the product, carry out the test run and work at the electrical unit.

Is this answer helpful?

A

No, do not operate in non-stationary systems like railway vehicles, aircraft and spacecraft.

Is this answer helpful?

A

Switch off, de-energize and eliminate mechanical blocking. If it cannot be fixed, the product may need replacement.

Is this answer helpful?

M: QW-35-FL

Advantages and Disadvantages

Advantages

  • High performance at 14000 rpm with 220 cubic meters per hour airflow capacity for cooling needs.
  • Lightweight at 0.21 kg making it easy to integrate into compact built-in device designs.
  • Protection class III ensures safety against electrical voltage risks when installed correctly.
  • Durable design allows operation up to 70 degrees Celsius in controlled environments.
  • Clear safety classifications guide users on risk levels like Danger and Warning effectively.
VS

Disadvantages

  • Product cannot be repaired internally and must be replaced if faults occur during operation.
  • PWM speed control is not permitted requiring strict adherence to supply voltage limits.
  • Not suitable for conveying abrasive, corrosive, or high dust load air mixes effectively.
  • Requires skilled electricians for installation which limits DIY implementation options.
  • High operating temperature creates a burn risk requiring protective measures on housing.
M: QW-35-FL

Product Specification

Fan connector

3-Pin

Dimensions

3.15 x 3.15 x 0.98 in (WxHxD)

Fan speed

1500 rpm

Airflow

19.42 CFM

Noise level

12 dB(A)

Fan bearing

Sleeve bearing

Color

Black (Frame), Black (Rotor)

M: QW-35-FL

Product Description

Overview

When evaluating industrial cooling solutions, the ebm-papst 8214 JH4 stands out as a reliable option for specific airflow needs. This guide provides an overview based on the official documentation available for the Papst 8214 JH4, 80mm Manual. Understanding the specifications and safety protocols is critical for anyone considering this component for their project.

Safety

Safety is the number one priority when installing this device. The manual clearly outlines hazard classifications such as Danger, Warning, and Caution. Danger indicates potential health risks or fatal injuries. Warning suggests major or fatal injuries if ignored. Caution covers minor injuries or property damage. Only skilled electricians are permitted to install or service the product. Unauthorized changes to the product are strictly prohibited. You must stop the product immediately if it suffers from impermissible loading like impact or overvoltage.

Use

This product is designed exclusively as a built-in device for conveying air. Misuse includes conveying air with abrasive particles or highly corrosive effects. It is not suitable for inflammable gases or medical life-saving devices. Operating in non-stationary systems like aircraft is forbidden. You must ensure adequate supply and exhaust air to prevent blocked escape routes. Never direct the airflow at a potential source of fire due to the risk.

Specs

The unit operates at a nominal voltage of 24.0 V. It runs at a speed of 14,000 per minute and consumes 38.0 Watts of power. The maximum free-air flow reaches 220.0 cubic meters per hour. Noise levels can exceed 70 dB depending on installation. The ambient temperature for operation ranges from minus 20 to 70 degrees Celsius. Electrical connection must be made according to national regulations. Voltage control via supply voltage is permitted, but speed control via PWM is not allowed. Use ESD protective equipment during mounting to avoid damaging electronic components.

Care

Cleaning must be done with a moist cloth without pressure. Do not use acids or solvents. If the product is faulty, do not repair it; replace it with a new one. Dispose of the unit according to country regulations. Annual operation for 15 minutes is recommended if stored long-term. Always store the product in a dry and clean environment that is well protected to ensure longevity of your use.

M: QW-35-FL

© Copyright 2026 Manual.ly