MRP Ribbon Manual
PDF manual · 4 Pages
English

Quick check
Incorrect answer, please try again.
Chat with your MRP Ribbon manual using AI
Get instant AI answers from your MRP Ribbon manual
Ask anything about the MRP Ribbon. Answers come from this manual, with the pages they are based on.
Ribbon Maintenance Schedule
Remove all dirt and mud from the stanchions after every ride to prevent damage.
Visually inspect the stanchions for damage or wear after every ride.
Verify that all bolts and fasteners are tightened to the correct torque values.
Measure and adjust both positive and negative air chamber pressures as needed.
Drain old bath oil and refill with fresh oil; reduce interval to 30 hours in muddy conditions.
Inspect the air spring assembly and apply lubrication if signs of dryness or friction are present.
Install new wiper seals; reduce interval to 75 hours in muddy conditions (standard is 100 hours).
Completely drain and replace the internal damper oil to maintain proper damping performance.
Ask a Question
Do you recommend Ribbon?
Yes NoFrequently Asked Questions
Ramp Control is a 16-position knob inside the air spring assembly that adjusts the ending-stroke curve. It is designed to work independently of your damper settings and air pressure, letting you choose plush traction with bottom-out resistance or a more linear feel that still supports big hits.
Is this answer helpful?
A commonly used starting approach is to set positive air pressure in psi to about 40% of rider weight in pounds. Negative chamber pressure can be slightly higher or lower based on preferred sensitivity and feel. Use the manual's guidance and sample charts as your baseline.
Is this answer helpful?
Air pressure primarily changes spring rate (how the fork supports and stores energy). Compression damping changes how the fork resists during the compression stroke. Adjusting compression can make the fork feel firmer or more controlled without altering spring rate.
Is this answer helpful?
Recommended intervals vary by conditions. Under normal conditions, routine tasks like checking air spring, relube if needed, and damper oil service are spaced by specified hour marks. Under muddy conditions, key wear items and services occur sooner, including wiper seal replacement and more frequent inspections and cleaning.
Is this answer helpful?
The Ribbon fork uses a post mount for 180 mm rotors. If you want to use a larger rotor, you must use the appropriate disc brake adaptor recommended by your brake manufacturer to avoid serious injury or death.
Is this answer helpful?
When wheel or tire changes, relieve air pressure and compress the fork fully to bottom out. Confirm there is at least 1/8 inch (3 mm) clearance between the crown and the highest point on the tire at full bottom-out to ensure safe clearance in all riding conditions.
Is this answer helpful?
MRP provides a one-year warranty for material and workmanship defects from the date of purchase (or manufacture if proof cannot be verified). Warranty coverage can be voided by improper installation, adjustments not outlined in the manual, misuse, missing or altered serial numbers, and damage from crashes, falls, or abuse.
Is this answer helpful?
Advantages and Disadvantages
Advantages
- Ramp Control (16 positions) tunes ending-stroke behavior independently of damper and air pressure.
- Air spring and compression plus rebound adjustments help maintain traction and ride comfort.
- Super-supple small-bump compliance supports plush feel over rough terrain.
- Mud-aware maintenance intervals help keep performance consistent in harsher riding.
Disadvantages
- Muddy riding increases service frequency for seals and internal oil-related maintenance.
- Correct installation and adjustment are critical; improper setup can be hazardous.
- Rotor upgrades may require a compatible adapter to avoid safety risks.
- Requires routine checks like stanchion cleaning, fastener torque, and clearance verification.
Product Specification
Type
Suspension fork
Colors
black
Wheel size
29"
Travel
6.30 in
Suspension element
Air
Steerer
tapered 1.5"
Stanchion diameter
1.38 in
Axle system
0.59 in thru axle (Boost)
Brake system
Disc brake
Brake mount
Postmount
Weight
4.19 lb
Product Description
MRP Ribbon 29-inch 160 mm Suspension Fork - Manual-Tuned Plush Control
The MRP Ribbon 29-inch 160 mm Suspension Fork is built for riders who want a mountain fork that feels supple on small bumps but stays confident when trails get rough. Designed around air-spring adjustability, it lets you fine-tune ride feel across everything from punchy climbs to technical descents. If you are pairing setup with the MRP Ribbon 29" 160 mm Suspension Fork Manual, you will find clear guidance on installation, tuning, maintenance, and safe operation.
A standout feature is Ramp Control, a 16-position knob built into the air spring system. It reshapes the ending-stroke curve independently of your damper and air pressure, so you can aim for either plush, bottom-out resistance, or a more linear feel that uses full travel. Many riders start near the factory baseline (5 clicks from open) and then dial toward more control for steep, fast, or violent hits.
For damping feel, the fork uses an 8-position low-speed compression adjustment on the damper side plus rebound damping to manage how the fork returns after each compression. Rebound helps keep your front wheel tracking instead of bouncing off line. Compression damping changes how quickly the fork resists during the compression stroke, without changing spring rate, so you can filter rider-induced movement while keeping small-bump sensitivity.
Keeping performance consistent also matters. The recommended service intervals include more frequent attention under muddy conditions, such as replacing wiper seals and refreshing air-spring and damper oil at specified hour marks. Routine checks like stanchion inspection, cleaning, fastener torque verification, and air pressure confirmation help the fork keep its smooth, controlled behavior.
Torque specs and setup details are also part of the ownership experience. The manual calls out fastener torque ranges, guidance for cutting the steerer tube to correct length, and warnings about verifying rotor adapter compatibility when using larger rotors. It also recommends qualified installation to avoid hazards from improper fork mounting.
Top benefits (key results)
- Ramp Control (16 positions) lets you tune the ending-stroke feel without changing damper or air settings.
- Air-spring tuning supports a wide range of comfort-to-control riding styles.
- Rebound and compression adjustments help maintain traction and reduce harsh rebound behavior.
- Clear maintenance intervals help protect performance, especially in muddy conditions.
- Service-friendly design supports internal maintenance and oil refreshes when needed.
Top trade-offs (key results)
- More frequent maintenance is required when riding in mud.
- Setup and installation must be done correctly, ideally by a qualified mechanic.
- Rotor compatibility requires the right adapter if you move beyond the stock 180 mm setup.
- Clearance checks at full bottom-out are essential for safe tire and crown spacing.
Notes
- Register your Ribbon fork online and use the Support section for technical resources and tuning guidance.
- For warranty considerations, follow the manual for installation, adjustment, and maintenance to avoid exclusions.
Search for 67,706 Manuals online
Type-in Brand or Model